Re: [PATCH v2 1/2] drm/i915: Sanitycheck MMIO access early in driver load

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Matt,

> > We occasionally see the PCI device in a non-accessible state at the
> > point the driver is loaded.  When this happens, all BAR accesses will
> > read back as 0xFFFFFFFF.  Rather than reading registers and
> > misinterpreting their (invalid) values, let's specifically check for
> > 0xFFFFFFFF in a register that cannot have that value to see if the
> > device is accessible.
> > 
> > Signed-off-by: Matt Roper <matthew.d.roper@xxxxxxxxx>
> > Cc: Mika Kuoppala <mika.kuoppala@xxxxxxxxxxxxxxx>
> > Signed-off-by: Andi Shyti <andi.shyti@xxxxxxxxxxxxxxx>
> > ---
> >  drivers/gpu/drm/i915/intel_uncore.c | 35 +++++++++++++++++++++++++++++
> >  1 file changed, 35 insertions(+)
> > 
> > diff --git a/drivers/gpu/drm/i915/intel_uncore.c b/drivers/gpu/drm/i915/intel_uncore.c
> > index e1e1f34490c8e..0b69081d6d285 100644
> > --- a/drivers/gpu/drm/i915/intel_uncore.c
> > +++ b/drivers/gpu/drm/i915/intel_uncore.c
> > @@ -2602,11 +2602,46 @@ static int uncore_forcewake_init(struct intel_uncore *uncore)
> >  	return 0;
> >  }
> >  
> > +static int sanity_check_mmio_access(struct intel_uncore *uncore)
> > +{
> > +	struct drm_i915_private *i915 = uncore->i915;
> > +	int ret;
> > +
> > +	if (GRAPHICS_VER(i915) < 8)
> > +		return 0;
> > +
> > +	/*
> > +	 * Sanitycheck that MMIO access to the device is working properly.  If
> > +	 * the CPU is unable to communcate with a PCI device, BAR reads will
> > +	 * return 0xFFFFFFFF.  Let's make sure the device isn't in this state
> > +	 * before we start trying to access registers.
> > +	 *
> > +	 * We use the primary GT's forcewake register as our guinea pig since
> > +	 * it's been around since HSW and it's a masked register so the upper
> > +	 * 16 bits can never read back as 1's if device access is operating
> > +	 * properly.
> > +	 *
> > +	 * If MMIO isn't working, we'll wait up to 2 seconds to see if it
> > +	 * recovers, then give up.
> > +	 */
> > +	ret = intel_wait_for_register_fw(uncore, FORCEWAKE_MT, 0, 0, 2000000);
> 
> It looks like you lost the check for 0xFFFFFFFF specifically.  In fact
> with a mask/value of 0, isn't this always going to just always pass
> immediately?

uh... yes... sorry, I just got confused and lost track of the
goal of the patch.

Sorry, then please ignore... I don't see then how
intel_wait_for_register_fw() can be used with a '!='.

Please, ignore this v2.

Thanks and sorry, again,
Andi

> We don't know what the value of this register will be (there may or may
> not be some bits set), but we need to make sure that it isn't 0xFFFFFFFF
> because that means we're not even truly accessing the register, just
> hitting a PCI BAR read failure.
> 
> 
> Matt
> 
> > +	if (ret == -ETIMEDOUT) {
> > +		drm_err(&i915->drm, "Device is non-operational; MMIO access returns 0xFFFFFFFF!\n");
> > +		return -EIO;
> > +	}
> > +
> > +	return 0;
> > +}
> > +
> >  int intel_uncore_init_mmio(struct intel_uncore *uncore)
> >  {
> >  	struct drm_i915_private *i915 = uncore->i915;
> >  	int ret;
> >  
> > +	ret = sanity_check_mmio_access(uncore);
> > +	if (ret)
> > +		return ret;
> > +
> >  	/*
> >  	 * The boot firmware initializes local memory and assesses its health.
> >  	 * If memory training fails, the punit will have been instructed to
> > -- 
> > 2.39.2
> > 
> 
> -- 
> Matt Roper
> Graphics Software Engineer
> Linux GPU Platform Enablement
> Intel Corporation



[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux