On 2/27/2023 4:45 AM, Dmitry Baryshkov wrote:
On Mon, 27 Feb 2023 at 01:49, Abhinav Kumar <quic_abhinavk@xxxxxxxxxxx> wrote:
On 2/26/2023 5:09 AM, Dmitry Baryshkov wrote:
On 26/02/2023 02:47, Abhinav Kumar wrote:
Hi Dmitry
On 2/25/2023 7:23 AM, Dmitry Baryshkov wrote:
On 25/02/2023 02:36, Abhinav Kumar wrote:
On 2/24/2023 3:53 PM, Dmitry Baryshkov wrote:
On Sat, 25 Feb 2023 at 00:26, Abhinav Kumar
<quic_abhinavk@xxxxxxxxxxx> wrote:
On 2/24/2023 1:36 PM, Dmitry Baryshkov wrote:
24 февраля 2023 г. 23:23:03 GMT+02:00, Abhinav Kumar
<quic_abhinavk@xxxxxxxxxxx> пишет:
On 2/24/2023 1:13 PM, Dmitry Baryshkov wrote:
On 24/02/2023 21:40, Kuogee Hsieh wrote:
Add DSC helper functions based on DSC configuration profiles
to produce
DSC related runtime parameters through both table look up and
runtime
calculation to support DSC on DPU.
There are 6 different DSC configuration profiles are supported
currently.
DSC configuration profiles are differiented by 5 keys, DSC
version (V1.1),
chroma (444/422/420), colorspace (RGB/YUV), bpc(8/10),
bpp (6/7/7.5/8/9/10/12/15) and SCR (0/1).
Only DSC version V1.1 added and V1.2 will be added later.
These helpers should go to
drivers/gpu/drm/display/drm_dsc_helper.c
Also please check that they can be used for i915 or for amdgpu
(ideally for both of them).
No, it cannot. So each DSC encoder parameter is calculated based
on the HW core which is being used.
They all get packed to the same DSC structure which is the
struct drm_dsc_config but the way the parameters are computed is
specific to the HW.
This DPU file helper still uses the drm_dsc_helper's
drm_dsc_compute_rc_parameters() like all other vendors do but
the parameters themselves are very HW specific and belong to
each vendor's dir.
This is not unique to MSM.
Lets take a few other examples:
AMD:
https://gitlab.freedesktop.org/drm/msm/-/blob/msm-next/drivers/gpu/drm/amd/display/dc/dml/dsc/rc_calc_fpu.c#L165
i915:
https://gitlab.freedesktop.org/drm/msm/-/blob/msm-next/drivers/gpu/drm/i915/display/intel_vdsc.c#L379
I checked several values here. Intel driver defines more bpc/bpp
combinations, but the ones which are defined in intel_vdsc and in
this patch seem to match. If there are major differences there,
please point me to the exact case.
I remember that AMD driver might have different values.
Some values in the rc_params table do match. But the
rc_buf_thresh[] doesnt.
Because later they do:
vdsc_cfg->rc_buf_thresh[i] = rc_buf_thresh[i] >> 6;
https://gitlab.freedesktop.org/drm/msm/-/blob/msm-next/drivers/gpu/drm/i915/display/intel_vdsc.c#L40
Vs
+static u16 dpu_dsc_rc_buf_thresh[DSC_NUM_BUF_RANGES - 1] = {
+ 0x0e, 0x1c, 0x2a, 0x38, 0x46, 0x54,
+ 0x62, 0x69, 0x70, 0x77, 0x79, 0x7b, 0x7d, 0x7e
+};
I'd prefer to have 896, 1792, etc. here, as those values come from the
standard. As it's done in the Intel driver.
Got it, thanks
I dont know the AMD calculation very well to say that moving this
to the
helper is going to help.
Those calculations correspond (more or less) at the first glance to
what intel does for their newer generations. I think that's not our
problem for now.
Well, we have to figure out if each value matches and if each of
them come from the spec for us and i915 and from which section. So
it is unfortunately our problem.
Otherwise it will have to be handled by Marijn, me or anybody else
wanting to hack up the DSC code. Or by anybody adding DSC support to
the next platform and having to figure out the difference between
i915, msm and their platform.
Yes, I wonder why the same doubt didn't arise when the other vendors
added their support both from other maintainers and others.
Which makes me think that like I wrote in my previous response, these
are "recommended" values in the spec but its not mandatory.
I think, it is because there were no other drivers to compare. In other
words, for a first driver it is pretty logical to have everything
handled on its own. As soon as we start getting other implementations of
a feature, it becomes logical to think if the code can be generalized.
This is what we see we with the HDCP series or with the code being moved
to DP helpers.
We were not the second, MSM was/is the third to add support for DSC afer
i915 and AMD. Thats what made me think why whoever was the second didnt
end up generalizing. Was it just missed out or was it intentionally left
in the vendor driver.
I didn't count AMD here, since it calculates some of the params rather
than using the fixed ones from the model.
Moving this to the drm_dsc_helper is generalizing the tables and not
giving room for the vendors to customize even if they want to (which
the spec does allow).
That depends on the API you select. For example, in
intel_dsc_compute_params() I see customization being applied to
rc_buf_thresh in 6bpp case. I'd leave that to the i915 driver.
Thanks for going through the i915 to figure out that the 6bpp is handled
in a customized way. So what you are saying is let the helper first fill
up the recommended values of the spec, whatever is changed from that let
the vendor driver override that.
Thats where the case-by-case handling comes.
Why not we do this way? Like you mentioned lets move these tables to the
drm_dsc_helper and let MSM driver first use those.
Then in a separate patchset if i915 and AMD would like to move to that,
let them handle it for their respective drivers instead of MSM going
through whats customized for each calculation and doing it.
I am hesitant to take up that effort.
Writing a tool to convert model's rc_Nbpc_Mbpp_foo.cfg into C
languages structures used by Intel code took 15-20 minutes. Plugging
generated structures took another 5 minutes. I will send the patches
later today or tomorrow, as I find a time slot to clean them. Thank
you for spending more time on arguing than it took me to generate &
verify the data.
Great, we will wait for your patches. We didnt intend to spend time on
this at this point. We always wanted to take it up in a separate series
of moving the tables.
You preferred not to wait. Upto you.
So thanks for doing it.
If the recommended values work for the vendor, they can clean it up and
move to the drm_dsc_helper themselves and preserving their
customizations rather than one vendor doing it for all of them.
In case the driver needs to perform customization of the params, nothing
stops it drop applying after filling all the RC params in the
drm_dsc_config struct via the generic helper.
So if this has any merit and if you or Marijn would like to take it
up, go for it. We would do the same thing as either of you would have
to in terms of figuring out the difference between msm and the i915 code.
This is not a generic API we are trying to put in a helper, these are
hard-coded tables so there is a difference between looking at these Vs
looking at some common code which can move to the core.
Also, i think its too risky to change other drivers to use
whatever math
we put in the drm_dsc_helper to compute thr RC params because
their code
might be computing and using this tables differently.
Its too much ownership for MSM developers to move this to
drm_dsc_helper
and own that as it might cause breakage of basic DSC even if some
values
are repeated.
It's time to stop thinking about ownership and start thinking about
shared code. We already have two instances of DSC tables. I don't
think having a third instance, which is a subset of an existing
dataset, would be beneficial to anybody.
AMD has complicated code which supports half-bit bpp and calculates
some of the parameters. But sharing data with the i915 driver is
straightforward.
Sorry, but I would like to get an ack from i915 folks if this is going
to be useful to them if we move this to helper because we have to
look at every table. Not just one.
Added i915 maintainers to the CC list for them to be able to answer.
Thanks, lets wait to hear from them about where finally these tables
should go but thats can be taken up as a separate effort too.
Also, this is just 1.1, we will add more tables for 1.2. So we will
have to end up changing both 1.1 and 1.2 tables as they are
different for QC.
I haven't heard back from Kuogee about the possible causes of using
rc/qp values from 1.2 even for 1.1 panels. Maybe you can comment on
that? In other words, can we always stick to the values from 1.2
standard? What will be the drawback?
Otherwise, we'd have to have two different sets of values, like you
do in your vendor driver.
I have responded to this in the other email.
All this being said, even if the rc tables move the drm_dsc_helper
either now or later on, we will still need MSM specific calculations
for many of the other encoder parameters (which are again either
hard-coded or calculated). Please refer to the
sde_dsc_populate_dsc_config() downstream. And yes, you will not find
those in the DP spec directly.
So we will still need a dsc helper for MSM calculations to be common
for DSI / DP irrespective of where the tables go.
So, lets finalize that first.
I went on and trimmed sde_dsc_populate_dsc_config() to remove
duplication with the drm_dsc_compute_rc_parameters() (which we already
use for the MSM DSI DSC).
Not much is left:
dsc->first_line_bpg_offset set via the switch
dsc->line_buf_depth = bpc + 1;
dsc->mux_word_size = bpc > 10 ? DSC_MUX_WORD_SIZE_12_BPC:
DSC_MUX_WORD_SIZE_8_10_BPC;
if ((dsc->dsc_version_minor == 0x2) && (dsc->native_420))
dsc->nsl_bpg_offset = (2048 *
(DIV_ROUND_UP(dsc->second_line_bpg_offset,
(dsc->slice_height - 1))));
dsc->initial_scale_value = 8 * dsc->rc_model_size /
(dsc->rc_model_size - dsc->initial_offset);
mux_word_size comes from the standard (must)
initial_scale_value calculation is recommended, but not required
nsl_bpg_offset follows the standard (must), also see below (*).
first_line_bpg_offset calculation differs between three drivers. The
standard also provides a recommended formulas. I think we can leave it
as is for now.
I think, that mux_word_size and nsl_bpg_offset calculation should be
moved to drm_dsc_compute_rc_parameters(), while leaving
initial_scale_value in place (in the driver code).
* I think nsl_bpg_offset is slightly incorrectly calculated. Standard
demands that it is set to 'second_line_bpg_offset / (slice_height - 1),
rounded up to 16 fraction bits', while SDE driver code sets it to the
value rounded up to the next integer (having 16 fraction bits
representation).
In my opinion correct calculation should be:
dsc->nsl_bpg_offset = DIV_ROUND_UP(2048 * dsc->second_line_bpg_offset,
(dsc->slice_height - 1));
Could you please check, which one is correct according to the standard?
Sure, i will check about nsl_bpg_offset. But sorry if I was not more
clear about this but sde_dsc_populate_dsc_config() is only one example
which from your analysis can be moved to the drm_dsc_helper() but not
the initial line calculation _dce_dsc_initial_line_calc(),
_dce_dsc_ich_reset_override_needed() , _dce_dsc_setup_helper().
The initial_line is already calculated in dpu_encoder.c. As for the
_dce_dsc_ich_reset_override_needed(), I don't think we support partial
updates in the upstream driver.
All of these are again common between DSI and DP.
So in addition to thinking about what can be moved to the drm_dsc_helper
also think about what is specific to MSM but common to DSI and DP modules.
That was the bigger picture I was trying to convey.
_dce_dsc_initial_line_calc which will get expanded with v1.2 gets added
has much more than whats there in upstream today.
Dumping everything in dpu_encoder is not the solution. Sorry.
