Re: [PATCH v3 3/6] arm64: dts: qcom: sm8350: move more nodes to correct place

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 9.02.2023 14:38, Dmitry Baryshkov wrote:
> Continue ordering DT nodes by their address. Move RNG, UFS, system NoC
> and SLPI nodes to the proper position.
> 
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>

Konrad
>  arch/arm64/boot/dts/qcom/sm8350.dtsi | 314 +++++++++++++--------------
>  1 file changed, 157 insertions(+), 157 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> index b85bd8fd28c0..8bf38d350521 100644
> --- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
> @@ -1421,6 +1421,13 @@ spi13: spi@a94000 {
>  			};
>  		};
>  
> +		rng: rng@10d3000 {
> +			compatible = "qcom,prng-ee";
> +			reg = <0 0x010d3000 0 0x1000>;
> +			clocks = <&rpmhcc RPMH_HWKM_CLK>;
> +			clock-names = "core";
> +		};
> +
>  		config_noc: interconnect@1500000 {
>  			compatible = "qcom,sm8350-config-noc";
>  			reg = <0 0x01500000 0 0xa580>;
> @@ -1641,18 +1648,76 @@ pcie1_phy: phy@1c0f000 {
>  			status = "disabled";
>  		};
>  
> -		lpass_ag_noc: interconnect@3c40000 {
> -			compatible = "qcom,sm8350-lpass-ag-noc";
> -			reg = <0 0x03c40000 0 0xf080>;
> -			#interconnect-cells = <2>;
> -			qcom,bcm-voters = <&apps_bcm_voter>;
> +		ufs_mem_hc: ufshc@1d84000 {
> +			compatible = "qcom,sm8350-ufshc", "qcom,ufshc",
> +				     "jedec,ufs-2.0";
> +			reg = <0 0x01d84000 0 0x3000>;
> +			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
> +			phys = <&ufs_mem_phy_lanes>;
> +			phy-names = "ufsphy";
> +			lanes-per-direction = <2>;
> +			#reset-cells = <1>;
> +			resets = <&gcc GCC_UFS_PHY_BCR>;
> +			reset-names = "rst";
> +
> +			power-domains = <&gcc UFS_PHY_GDSC>;
> +
> +			iommus = <&apps_smmu 0xe0 0x0>;
> +
> +			clock-names =
> +				"core_clk",
> +				"bus_aggr_clk",
> +				"iface_clk",
> +				"core_clk_unipro",
> +				"ref_clk",
> +				"tx_lane0_sync_clk",
> +				"rx_lane0_sync_clk",
> +				"rx_lane1_sync_clk";
> +			clocks =
> +				<&gcc GCC_UFS_PHY_AXI_CLK>,
> +				<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
> +				<&gcc GCC_UFS_PHY_AHB_CLK>,
> +				<&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
> +				<&rpmhcc RPMH_CXO_CLK>,
> +				<&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
> +				<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
> +				<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
> +			freq-table-hz =
> +				<75000000 300000000>,
> +				<0 0>,
> +				<0 0>,
> +				<75000000 300000000>,
> +				<0 0>,
> +				<0 0>,
> +				<0 0>,
> +				<0 0>;
> +			status = "disabled";
>  		};
>  
> -		compute_noc: interconnect@a0c0000 {
> -			compatible = "qcom,sm8350-compute-noc";
> -			reg = <0 0x0a0c0000 0 0xa180>;
> -			#interconnect-cells = <2>;
> -			qcom,bcm-voters = <&apps_bcm_voter>;
> +		ufs_mem_phy: phy@1d87000 {
> +			compatible = "qcom,sm8350-qmp-ufs-phy";
> +			reg = <0 0x01d87000 0 0x1c4>;
> +			#address-cells = <2>;
> +			#size-cells = <2>;
> +			ranges;
> +			clock-names = "ref",
> +				      "ref_aux";
> +			clocks = <&rpmhcc RPMH_CXO_CLK>,
> +				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
> +
> +			resets = <&ufs_mem_hc 0>;
> +			reset-names = "ufsphy";
> +			status = "disabled";
> +
> +			ufs_mem_phy_lanes: phy@1d87400 {
> +				reg = <0 0x01d87400 0 0x188>,
> +				      <0 0x01d87600 0 0x200>,
> +				      <0 0x01d87c00 0 0x200>,
> +				      <0 0x01d87800 0 0x188>,
> +				      <0 0x01d87a00 0 0x200>;
> +				#clock-cells = <1>;
> +				#phy-cells = <0>;
> +			};
>  		};
>  
>  		ipa: ipa@1e40000 {
> @@ -1700,6 +1765,13 @@ tcsr_mutex: hwlock@1f40000 {
>  			#hwlock-cells = <1>;
>  		};
>  
> +		lpass_ag_noc: interconnect@3c40000 {
> +			compatible = "qcom,sm8350-lpass-ag-noc";
> +			reg = <0 0x03c40000 0 0xf080>;
> +			#interconnect-cells = <2>;
> +			qcom,bcm-voters = <&apps_bcm_voter>;
> +		};
> +
>  		mpss: remoteproc@4080000 {
>  			compatible = "qcom,sm8350-mpss-pas";
>  			reg = <0x0 0x04080000 0x0 0x4040>;
> @@ -1742,6 +1814,74 @@ IPCC_MPROC_SIGNAL_GLINK_QMP
>  			};
>  		};
>  
> +		slpi: remoteproc@5c00000 {
> +			compatible = "qcom,sm8350-slpi-pas";
> +			reg = <0 0x05c00000 0 0x4000>;
> +
> +			interrupts-extended = <&pdc 9 IRQ_TYPE_LEVEL_HIGH>,
> +					      <&smp2p_slpi_in 0 IRQ_TYPE_EDGE_RISING>,
> +					      <&smp2p_slpi_in 1 IRQ_TYPE_EDGE_RISING>,
> +					      <&smp2p_slpi_in 2 IRQ_TYPE_EDGE_RISING>,
> +					      <&smp2p_slpi_in 3 IRQ_TYPE_EDGE_RISING>;
> +			interrupt-names = "wdog", "fatal", "ready",
> +					  "handover", "stop-ack";
> +
> +			clocks = <&rpmhcc RPMH_CXO_CLK>;
> +			clock-names = "xo";
> +
> +			power-domains = <&rpmhpd SM8350_LCX>,
> +					<&rpmhpd SM8350_LMX>;
> +			power-domain-names = "lcx", "lmx";
> +
> +			memory-region = <&pil_slpi_mem>;
> +
> +			qcom,qmp = <&aoss_qmp>;
> +
> +			qcom,smem-states = <&smp2p_slpi_out 0>;
> +			qcom,smem-state-names = "stop";
> +
> +			status = "disabled";
> +
> +			glink-edge {
> +				interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
> +							     IPCC_MPROC_SIGNAL_GLINK_QMP
> +							     IRQ_TYPE_EDGE_RISING>;
> +				mboxes = <&ipcc IPCC_CLIENT_SLPI
> +						IPCC_MPROC_SIGNAL_GLINK_QMP>;
> +
> +				label = "slpi";
> +				qcom,remote-pid = <3>;
> +
> +				fastrpc {
> +					compatible = "qcom,fastrpc";
> +					qcom,glink-channels = "fastrpcglink-apps-dsp";
> +					label = "sdsp";
> +					qcom,non-secure-domain;
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					compute-cb@1 {
> +						compatible = "qcom,fastrpc-compute-cb";
> +						reg = <1>;
> +						iommus = <&apps_smmu 0x0541 0x0>;
> +					};
> +
> +					compute-cb@2 {
> +						compatible = "qcom,fastrpc-compute-cb";
> +						reg = <2>;
> +						iommus = <&apps_smmu 0x0542 0x0>;
> +					};
> +
> +					compute-cb@3 {
> +						compatible = "qcom,fastrpc-compute-cb";
> +						reg = <3>;
> +						iommus = <&apps_smmu 0x0543 0x0>;
> +						/* note: shared-cb = <4> in downstream */
> +					};
> +				};
> +			};
> +		};
> +
>  		pdc: interrupt-controller@b220000 {
>  			compatible = "qcom,sm8350-pdc", "qcom,pdc";
>  			reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
> @@ -2012,153 +2152,6 @@ qup_i2c19_default: qup-i2c19-default-state {
>  			};
>  		};
>  
> -		rng: rng@10d3000 {
> -			compatible = "qcom,prng-ee";
> -			reg = <0 0x010d3000 0 0x1000>;
> -			clocks = <&rpmhcc RPMH_HWKM_CLK>;
> -			clock-names = "core";
> -		};
> -
> -		ufs_mem_hc: ufshc@1d84000 {
> -			compatible = "qcom,sm8350-ufshc", "qcom,ufshc",
> -				     "jedec,ufs-2.0";
> -			reg = <0 0x01d84000 0 0x3000>;
> -			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
> -			phys = <&ufs_mem_phy_lanes>;
> -			phy-names = "ufsphy";
> -			lanes-per-direction = <2>;
> -			#reset-cells = <1>;
> -			resets = <&gcc GCC_UFS_PHY_BCR>;
> -			reset-names = "rst";
> -
> -			power-domains = <&gcc UFS_PHY_GDSC>;
> -
> -			iommus = <&apps_smmu 0xe0 0x0>;
> -
> -			clock-names =
> -				"core_clk",
> -				"bus_aggr_clk",
> -				"iface_clk",
> -				"core_clk_unipro",
> -				"ref_clk",
> -				"tx_lane0_sync_clk",
> -				"rx_lane0_sync_clk",
> -				"rx_lane1_sync_clk";
> -			clocks =
> -				<&gcc GCC_UFS_PHY_AXI_CLK>,
> -				<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
> -				<&gcc GCC_UFS_PHY_AHB_CLK>,
> -				<&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
> -				<&rpmhcc RPMH_CXO_CLK>,
> -				<&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
> -				<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
> -				<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
> -			freq-table-hz =
> -				<75000000 300000000>,
> -				<0 0>,
> -				<0 0>,
> -				<75000000 300000000>,
> -				<0 0>,
> -				<0 0>,
> -				<0 0>,
> -				<0 0>;
> -			status = "disabled";
> -		};
> -
> -		ufs_mem_phy: phy@1d87000 {
> -			compatible = "qcom,sm8350-qmp-ufs-phy";
> -			reg = <0 0x01d87000 0 0x1c4>;
> -			#address-cells = <2>;
> -			#size-cells = <2>;
> -			ranges;
> -			clock-names = "ref",
> -				      "ref_aux";
> -			clocks = <&rpmhcc RPMH_CXO_CLK>,
> -				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
> -
> -			resets = <&ufs_mem_hc 0>;
> -			reset-names = "ufsphy";
> -			status = "disabled";
> -
> -			ufs_mem_phy_lanes: phy@1d87400 {
> -				reg = <0 0x01d87400 0 0x188>,
> -				      <0 0x01d87600 0 0x200>,
> -				      <0 0x01d87c00 0 0x200>,
> -				      <0 0x01d87800 0 0x188>,
> -				      <0 0x01d87a00 0 0x200>;
> -				#clock-cells = <1>;
> -				#phy-cells = <0>;
> -			};
> -		};
> -
> -		slpi: remoteproc@5c00000 {
> -			compatible = "qcom,sm8350-slpi-pas";
> -			reg = <0 0x05c00000 0 0x4000>;
> -
> -			interrupts-extended = <&pdc 9 IRQ_TYPE_LEVEL_HIGH>,
> -					      <&smp2p_slpi_in 0 IRQ_TYPE_EDGE_RISING>,
> -					      <&smp2p_slpi_in 1 IRQ_TYPE_EDGE_RISING>,
> -					      <&smp2p_slpi_in 2 IRQ_TYPE_EDGE_RISING>,
> -					      <&smp2p_slpi_in 3 IRQ_TYPE_EDGE_RISING>;
> -			interrupt-names = "wdog", "fatal", "ready",
> -					  "handover", "stop-ack";
> -
> -			clocks = <&rpmhcc RPMH_CXO_CLK>;
> -			clock-names = "xo";
> -
> -			power-domains = <&rpmhpd SM8350_LCX>,
> -					<&rpmhpd SM8350_LMX>;
> -			power-domain-names = "lcx", "lmx";
> -
> -			memory-region = <&pil_slpi_mem>;
> -
> -			qcom,qmp = <&aoss_qmp>;
> -
> -			qcom,smem-states = <&smp2p_slpi_out 0>;
> -			qcom,smem-state-names = "stop";
> -
> -			status = "disabled";
> -
> -			glink-edge {
> -				interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
> -							     IPCC_MPROC_SIGNAL_GLINK_QMP
> -							     IRQ_TYPE_EDGE_RISING>;
> -				mboxes = <&ipcc IPCC_CLIENT_SLPI
> -						IPCC_MPROC_SIGNAL_GLINK_QMP>;
> -
> -				label = "slpi";
> -				qcom,remote-pid = <3>;
> -
> -				fastrpc {
> -					compatible = "qcom,fastrpc";
> -					qcom,glink-channels = "fastrpcglink-apps-dsp";
> -					label = "sdsp";
> -					qcom,non-secure-domain;
> -					#address-cells = <1>;
> -					#size-cells = <0>;
> -
> -					compute-cb@1 {
> -						compatible = "qcom,fastrpc-compute-cb";
> -						reg = <1>;
> -						iommus = <&apps_smmu 0x0541 0x0>;
> -					};
> -
> -					compute-cb@2 {
> -						compatible = "qcom,fastrpc-compute-cb";
> -						reg = <2>;
> -						iommus = <&apps_smmu 0x0542 0x0>;
> -					};
> -
> -					compute-cb@3 {
> -						compatible = "qcom,fastrpc-compute-cb";
> -						reg = <3>;
> -						iommus = <&apps_smmu 0x0543 0x0>;
> -						/* note: shared-cb = <4> in downstream */
> -					};
> -				};
> -			};
> -		};
> -
>  		sdhc_2: mmc@8804000 {
>  			compatible = "qcom,sm8350-sdhci", "qcom,sdhci-msm-v5";
>  			reg = <0 0x08804000 0 0x1000>;
> @@ -2307,6 +2300,13 @@ system-cache-controller@9200000 {
>  			reg-names = "llcc_base", "llcc_broadcast_base";
>  		};
>  
> +		compute_noc: interconnect@a0c0000 {
> +			compatible = "qcom,sm8350-compute-noc";
> +			reg = <0 0x0a0c0000 0 0xa180>;
> +			#interconnect-cells = <2>;
> +			qcom,bcm-voters = <&apps_bcm_voter>;
> +		};
> +
>  		usb_1: usb@a6f8800 {
>  			compatible = "qcom,sm8350-dwc3", "qcom,dwc3";
>  			reg = <0 0x0a6f8800 0 0x400>;



[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux