[PATCH v2 2/2] backlight: pwm_bl: Don't rely on a disabled PWM emiting inactive state

[Uwe Kleine-König <u.kleine-koenig@xxxxxxxxxxxxxx>]

Most but not all PWMs drive the PWM pin to its inactive state when
disabled. However if there is no enable_gpio and no regulator the PWM
must drive the inactive state to actually disable the backlight.

So keep the PWM on in this case.

Note that to determine if there is a regulator some effort is required
because it might happen that there isn't actually one but the regulator
core gave us a dummy. (A nice side effect is that this makes the
regulator actually optional even on fully constrained systems.)

This fixes backlight disabling e.g. on i.MX6 when an inverted PWM is
used.

Hint for the future: If this change results in a regression, the bug is
in the lowlevel PWM driver.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@xxxxxxxxxxxxxx>
---
 drivers/video/backlight/pwm_bl.c | 30 ++++++++++++++++++++++--------
 1 file changed, 22 insertions(+), 8 deletions(-)

diff --git a/drivers/video/backlight/pwm_bl.c b/drivers/video/backlight/pwm_bl.c
index 0509fecd5715..fb388148d98f 100644
--- a/drivers/video/backlight/pwm_bl.c
+++ b/drivers/video/backlight/pwm_bl.c
@@ -45,9 +45,11 @@ static void pwm_backlight_power_on(struct pwm_bl_data *pb)
 	if (pb->enabled)
 		return;
 
-	err = regulator_enable(pb->power_supply);
-	if (err < 0)
-		dev_err(pb->dev, "failed to enable power supply\n");
+	if (pb->power_supply) {
+		err = regulator_enable(pb->power_supply);
+		if (err < 0)
+			dev_err(pb->dev, "failed to enable power supply\n");
+	}
 
 	if (pb->post_pwm_on_delay)
 		msleep(pb->post_pwm_on_delay);
@@ -69,7 +71,8 @@ static void pwm_backlight_power_off(struct pwm_bl_data *pb)
 	if (pb->pwm_off_delay)
 		msleep(pb->pwm_off_delay);
 
-	regulator_disable(pb->power_supply);
+	if (pb->power_supply)
+		regulator_disable(pb->power_supply);
 	pb->enabled = false;
 }
 
@@ -109,8 +112,16 @@ static int pwm_backlight_update_status(struct backlight_device *bl)
 		pwm_backlight_power_off(pb);
 
 		pwm_get_state(pb->pwm, &state);
-		state.enabled = false;
 		state.duty_cycle = 0;
+		/*
+		 * We cannot assume a disabled PWM to drive its output to the
+		 * inactive state. If we have an enable GPIO and/or a regulator
+		 * we assume that this isn't relevant and we can disable the PWM
+		 * to save power. If however there is neither an enable GPIO nor
+		 * a regulator keep the PWM on be sure to get a constant
+		 * inactive output.
+		 */
+		state.enabled = !pb->power_supply && !pb->enable_gpio;
 		pwm_apply_state(pb->pwm, &state);
 	}
 
@@ -408,7 +419,7 @@ static int pwm_backlight_initial_power_state(const struct pwm_bl_data *pb)
 	if (pb->enable_gpio && gpiod_get_value_cansleep(pb->enable_gpio) == 0)
 		active = false;
 
-	if (!regulator_is_enabled(pb->power_supply))
+	if (pb->power_supply && !regulator_is_enabled(pb->power_supply))
 		active = false;
 
 	if (!pwm_is_enabled(pb->pwm))
@@ -489,10 +500,13 @@ static int pwm_backlight_probe(struct platform_device *pdev)
 		goto err_alloc;
 	}
 
-	pb->power_supply = devm_regulator_get(&pdev->dev, "power");
+	pb->power_supply = devm_regulator_get_optional(&pdev->dev, "power");
 	if (IS_ERR(pb->power_supply)) {
 		ret = PTR_ERR(pb->power_supply);
-		goto err_alloc;
+		if (ret == -ENODEV)
+			pb->power_supply = NULL;
+		else
+			goto err_alloc;
 	}
 
 	pb->pwm = devm_pwm_get(&pdev->dev, NULL);
-- 
2.39.0