On Fri, Dec 09, 2022 at 11:35:23AM +0100, Johan Hovold wrote:
> On Wed, Dec 07, 2022 at 02:00:11PM -0800, Bjorn Andersson wrote:
> > From: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
> >
> > The SC8280XP CRD has a EDP display on MDSS0 DP3, enable relevant nodes
> > and link it together with the backlight control.
> >
> > Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
> > Signed-off-by: Bjorn Andersson <quic_bjorande@xxxxxxxxxxx>
> > ---
> >
> > Changes since v4:
> > - None
> >
> > arch/arm64/boot/dts/qcom/sc8280xp-crd.dts | 72 ++++++++++++++++++++++-
> > 1 file changed, 71 insertions(+), 1 deletion(-)
> >
> > diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> > index f09810e3d956..a7d2384cbbe8 100644
> > --- a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> > +++ b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
> > @@ -20,7 +20,7 @@ aliases {
> > serial0 = &qup2_uart17;
> > };
> >
> > - backlight {
> > + backlight: backlight {
> > compatible = "pwm-backlight";
> > pwms = <&pmc8280c_lpg 3 1000000>;
> > enable-gpios = <&pmc8280_1_gpios 8 GPIO_ACTIVE_HIGH>;
> > @@ -34,6 +34,22 @@ chosen {
> > stdout-path = "serial0:115200n8";
> > };
> >
> > + vreg_edp_3p3: regulator-edp-3p3 {
> > + compatible = "regulator-fixed";
> > +
> > + regulator-name = "VREG_EDP_3P3";
>
> Please use the net name from the schematics here (i.e. "VCC3LCD").
>
This is the name used in the CRD schematics.
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > +
> > + gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>;
> > + enable-active-high;
> > +
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&edp_reg_en>;
> > +
> > + regulator-boot-on;
> > + };
> > +
> > vreg_edp_bl: regulator-edp-bl {
> > compatible = "regulator-fixed";
> >
> > @@ -230,6 +246,54 @@ vreg_l9d: ldo9 {
> > };
> > };
> >
> > +&dispcc0 {
> > + status = "okay";
> > +};
> > +
> > +&mdss0 {
> > + status = "okay";
> > +};
> > +
> > +&mdss0_dp3 {
> > + compatible = "qcom,sc8280xp-edp";
> > + status = "okay";
>
> Please move the status property last (i.e. after data-lanes).
>
Sorry for missing that.
> > +
> > + data-lanes = <0 1 2 3>;
> > +
> > + aux-bus {
> > + panel {
> > + compatible = "edp-panel";
> > + power-supply = <&vreg_edp_3p3>;
> > +
> > + backlight = <&backlight>;
> > +
> > + ports {
> > + port {
> > + edp_panel_in: endpoint {
> > + remote-endpoint = <&mdss0_dp3_out>;
> > + };
> > + };
> > + };
> > + };
> > + };
> > +
> > + ports {
> > + port@1 {
> > + reg = <1>;
> > + mdss0_dp3_out: endpoint {
> > + remote-endpoint = <&edp_panel_in>;
> > + };
> > + };
> > + };
> > +};
> > +
> > +&mdss0_dp3_phy {
> > + status = "okay";
>
> Same here.
>
Ditto.
> > +
> > + vdda-phy-supply = <&vreg_l6b>;
> > + vdda-pll-supply = <&vreg_l3b>;
> > +};
> > +
> > &pcie2a {
> > perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
> > wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
> > @@ -496,6 +560,12 @@ hastings_reg_en: hastings-reg-en-state {
> > &tlmm {
> > gpio-reserved-ranges = <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
> >
> > + edp_reg_en: edp-reg-en-state {
> > + pins = "gpio25";
> > + function = "gpio";
> > + output-enable;
>
> 'output-enable' is not valid for tlmm and causes the settings to be
> rejected:
>
> sc8280xp-tlmm f100000.pinctrl: pin_config_group_set op failed for group 25
> reg-fixed-voltage regulator-edp-3p3: Error applying setting, reverse things back
>
Thanks for spotting that, it doesn't seem to be needed for the gpio-regulator
driver anyways...
Regards,
Bjorn
> > + };
> > +
> > kybd_default: kybd-default-state {
> > disable-pins {
> > pins = "gpio102";
>
> Johan
