Re: [PATCH v7 0/6] clk/qcom: Support gdsc collapse polling using 'reset' interface

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, 7 Dec 2022 at 17:55, Bjorn Andersson <andersson@xxxxxxxxxx> wrote:
>
> On Wed, Dec 07, 2022 at 05:00:51PM +0100, Ulf Hansson wrote:
> > On Thu, 1 Dec 2022 at 23:57, Bjorn Andersson <andersson@xxxxxxxxxx> wrote:
> > >
> > > On Wed, Oct 05, 2022 at 02:36:58PM +0530, Akhil P Oommen wrote:
> > > >
> > >
> > > @Ulf, Akhil has a power-domain for a piece of hardware which may be
> > > voted active by multiple different subsystems (co-processors/execution
> > > contexts) in the system.
> > >
> > > As such, during the powering down sequence we don't wait for the
> > > power-domain to turn off. But in the event of an error, the recovery
> > > mechanism relies on waiting for the hardware to settle in a powered off
> > > state.
> > >
> > > The proposal here is to use the reset framework to wait for this state
> > > to be reached, before continuing with the recovery mechanism in the
> > > client driver.
> >
> > I tried to review the series (see my other replies), but I am not sure
> > I fully understand the consumer part.
> >
> > More exactly, when and who is going to pull the reset and at what point?
> >
> > >
> > > Given our other discussions on quirky behavior, do you have any
> > > input/suggestions on this?
> > >
> > > > Some clients like adreno gpu driver would like to ensure that its gdsc
> > > > is collapsed at hardware during a gpu reset sequence. This is because it
> > > > has a votable gdsc which could be ON due to a vote from another subsystem
> > > > like tz, hyp etc or due to an internal hardware signal. To allow
> > > > this, gpucc driver can expose an interface to the client driver using
> > > > reset framework. Using this the client driver can trigger a polling within
> > > > the gdsc driver.
> > >
> > > @Akhil, this description is fairly generic. As we've reached the state
> > > where the hardware has settled and we return to the client, what
> > > prevents it from being powered up again?
> > >
> > > Or is it simply a question of it hitting the powered-off state, not
> > > necessarily staying there?
> >
> > Okay, so it's indeed the GPU driver that is going to assert/de-assert
> > the reset at some point. Right?
> >
> > That seems like a reasonable approach to me, even if it's a bit
> > unclear under what conditions that could happen.
> >
>
> Generally the disable-path of the power-domain does not check that the
> power-domain is actually turned off, because the status might indicate
> that the hardware is voting for the power-domain to be on.

Is there a good reason why the HW needs to vote too, when the GPU
driver is already in control?

Or perhaps that depends on the running use case?

>
> As part of the recovery of the GPU after some fatal fault, the GPU
> driver does something which will cause the hardware votes for the
> power-domain to be let go, and then the driver does pm_runtime_put().

Okay. That "something", sounds like a device specific setting for the
corresponding gdsc, right?

So somehow the GPU driver needs to manage that setting, right?

>
> But in this case the GPU driver wants to ensure that the power-domain is
> actually powered down, before it does pm_runtime_get() again. To ensure
> that the hardware lost its state...

I see.

>
> The proposal here is to use a reset to reach into the power-domain
> provider and wait for the hardware to be turned off, before the GPU
> driver attempts turning the power-domain on again.
>
>
> In other words, there is no reset. This is a hack to make a normally
> asynchronous pd.power_off() to be synchronous in this particular case.

Alright, assuming I understood your clarifications above correctly
(thanks!), I think I have got a much better picture now.

Rather than abusing the reset interface, I think we should manage this
through the genpd's power on/off notifiers (GENPD_NOTIFY_OFF). The GPU
driver should register its corresponding device for them
(dev_pm_genpd_add_notifier()).

The trick however, is to make the behaviour of the power-domain for
the gdsc (the genpd->power_off() callback) conditional on whether the
HW is configured to vote or not. If the HW can vote, it should not
poll for the state - and vice versa when the HW can't vote.

Would this work?

Kind regards
Uffe



[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux