[PATCH v2 1/4] dt-bindings: display/msm: convert MDP5 schema to YAML format

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Convert the mdp5.txt into the yaml format. Changes to the existing (txt) schema:
 - MSM8996 has additional "iommu" clock, define it separately
 - Add new properties used on some of platforms:
   - interconnects, interconnect-names
   - iommus
   - power-domains
   - operating-points-v2, opp-table

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
---
 .../devicetree/bindings/display/msm/mdp5.txt  | 132 -----------------
 .../bindings/display/msm/qcom,mdp5.yaml       | 138 ++++++++++++++++++
 2 files changed, 138 insertions(+), 132 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/display/msm/mdp5.txt
 create mode 100644 Documentation/devicetree/bindings/display/msm/qcom,mdp5.yaml

diff --git a/Documentation/devicetree/bindings/display/msm/mdp5.txt b/Documentation/devicetree/bindings/display/msm/mdp5.txt
deleted file mode 100644
index 65d03c58dee6..000000000000
--- a/Documentation/devicetree/bindings/display/msm/mdp5.txt
+++ /dev/null
@@ -1,132 +0,0 @@
-Qualcomm adreno/snapdragon MDP5 display controller
-
-Description:
-
-This is the bindings documentation for the MDP5 display
-controller found in SoCs like MSM8974, APQ8084, MSM8916, MSM8994 and MSM8996.
-
-MDP5:
-Required properties:
-- compatible:
-  * "qcom,mdp5" - MDP5
-- reg: Physical base address and length of the controller's registers.
-- reg-names: The names of register regions. The following regions are required:
-  * "mdp_phys"
-- interrupts: Interrupt line from MDP5 to MDSS interrupt controller.
-- clocks: device clocks. See ../clocks/clock-bindings.txt for details.
-- clock-names: the following clocks are required.
--   * "bus"
--   * "iface"
--   * "core"
--   * "vsync"
-- ports: contains the list of output ports from MDP. These connect to interfaces
-  that are external to the MDP hardware, such as HDMI, DSI, EDP etc (LVDS is a
-  special case since it is a part of the MDP block itself).
-
-  Each output port contains an endpoint that describes how it is connected to an
-  external interface. These are described by the standard properties documented
-  here:
-	Documentation/devicetree/bindings/graph.txt
-	Documentation/devicetree/bindings/media/video-interfaces.txt
-
-  The availability of output ports can vary across SoC revisions:
-
-  For MSM8974 and APQ8084:
-	 Port 0 -> MDP_INTF0 (eDP)
-	 Port 1 -> MDP_INTF1 (DSI1)
-	 Port 2 -> MDP_INTF2 (DSI2)
-	 Port 3 -> MDP_INTF3 (HDMI)
-
-  For MSM8916:
-	 Port 0 -> MDP_INTF1 (DSI1)
-
-  For MSM8994 and MSM8996:
-	 Port 0 -> MDP_INTF1 (DSI1)
-	 Port 1 -> MDP_INTF2 (DSI2)
-	 Port 2 -> MDP_INTF3 (HDMI)
-
-Optional properties:
-- clock-names: the following clocks are optional:
-  * "lut"
-  * "tbu"
-  * "tbu_rt"
-
-Example:
-
-/ {
-	...
-
-	mdss: mdss@1a00000 {
-		compatible = "qcom,mdss";
-		reg = <0x1a00000 0x1000>,
-		      <0x1ac8000 0x3000>;
-		reg-names = "mdss_phys", "vbif_phys";
-
-		power-domains = <&gcc MDSS_GDSC>;
-
-		clocks = <&gcc GCC_MDSS_AHB_CLK>,
-			 <&gcc GCC_MDSS_AXI_CLK>,
-			 <&gcc GCC_MDSS_VSYNC_CLK>;
-		clock-names = "iface",
-			      "bus",
-			      "vsync"
-
-		interrupts = <0 72 0>;
-
-		interrupt-controller;
-		#interrupt-cells = <1>;
-
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		mdp: mdp@1a01000 {
-			compatible = "qcom,mdp5";
-			reg = <0x1a01000 0x90000>;
-			reg-names = "mdp_phys";
-
-			interrupt-parent = <&mdss>;
-			interrupts = <0 0>;
-
-			clocks = <&gcc GCC_MDSS_AHB_CLK>,
-				 <&gcc GCC_MDSS_AXI_CLK>,
-				 <&gcc GCC_MDSS_MDP_CLK>,
-				 <&gcc GCC_MDSS_VSYNC_CLK>;
-			clock-names = "iface",
-				      "bus",
-				      "core",
-				      "vsync";
-
-			ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				port@0 {
-					reg = <0>;
-					mdp5_intf1_out: endpoint {
-						remote-endpoint = <&dsi0_in>;
-					};
-				};
-			};
-		};
-
-		dsi0: dsi@1a98000 {
-			...
-			ports {
-				...
-				port@0 {
-					reg = <0>;
-					dsi0_in: endpoint {
-						remote-endpoint = <&mdp5_intf1_out>;
-					};
-				};
-				...
-			};
-			...
-		};
-
-		dsi_phy0: dsi-phy@1a98300 {
-			...
-		};
-	};
-};
diff --git a/Documentation/devicetree/bindings/display/msm/qcom,mdp5.yaml b/Documentation/devicetree/bindings/display/msm/qcom,mdp5.yaml
new file mode 100644
index 000000000000..cbcbe8b47e9b
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/msm/qcom,mdp5.yaml
@@ -0,0 +1,138 @@
+# SPDX-License-Identifier: GPL-2.0-only or BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/msm/qcom,mdp5.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Adreno/Snapdragon Mobile Display controller (MDP5)
+
+description: >
+  MDP5 display controller found in SoCs like MSM8974, APQ8084, MSM8916, MSM8994
+  and MSM8996.
+
+maintainers:
+  - Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
+  - Rob Clark <robdclark@xxxxxxxxx>
+
+properties:
+  compatible:
+    const: qcom,mdp5
+
+  reg:
+    maxItems: 1
+
+  reg-names:
+    items:
+      - const: mdp_phys
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    minItems: 4
+    maxItems: 7
+
+  clock-names:
+    oneOf:
+      - minItems: 4
+        items:
+          - const: iface
+          - const: bus
+          - const: core
+          - const: vsync
+          - const: lut
+          - const: tbu
+          - const: tbu_rt
+        #MSM8996 has additional iommu clock
+      - items:
+          - const: iface
+          - const: bus
+          - const: core
+          - const: iommu
+          - const: vsync
+
+  interconnects:
+    minItems: 1
+    items:
+      - description: Interconnect path from mdp0 (or a single mdp) port to the data bus
+      - description: Interconnect path from mdp1 port to the data bus
+      - description: Interconnect path from rotator port to the data bus
+
+  interconnect-names:
+    minItems: 1
+    items:
+      - const: mdp0-mem
+      - const: mdp1-mem
+      - const: rotator-mem
+
+  iommus:
+    items:
+      - description: Phandle to apps_smmu node with SID mask for Hard-Fail port0
+
+  power-domains:
+    maxItems: 1
+
+  operating-points-v2: true
+  opp-table:
+    type: object
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+    description: |
+      Contains the list of output ports from DPU device. These ports
+      connect to interfaces that are external to the DPU hardware,
+      such as DSI, DP etc. MDP5 devices support up to 4 ports::
+      one or two DSI ports, HDMI and eDP.
+
+    patternProperties:
+      "^port@[0-3]+$":
+        $ref: /schemas/graph.yaml#/properties/port
+
+    # at least one port is required
+    required:
+      - port@0
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - clocks
+  - clock-names
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-msm8916.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    display-controller@1a01000 {
+        compatible = "qcom,mdp5";
+        reg = <0x1a01000 0x90000>;
+        reg-names = "mdp_phys";
+
+        interrupt-parent = <&mdss>;
+        interrupts = <0>;
+
+        clocks = <&gcc GCC_MDSS_AHB_CLK>,
+                 <&gcc GCC_MDSS_AXI_CLK>,
+                 <&gcc GCC_MDSS_MDP_CLK>,
+                 <&gcc GCC_MDSS_VSYNC_CLK>;
+        clock-names = "iface",
+                      "bus",
+                      "core",
+                      "vsync";
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+                endpoint {
+                    remote-endpoint = <&dsi0_in>;
+                };
+            };
+        };
+    };
+...
-- 
2.35.1




[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux