On 01/12/2022 19:32, Kuogee Hsieh wrote:
On 11/30/2022 4:21 PM, Dmitry Baryshkov wrote:
On 01/12/2022 02:07, Dmitry Baryshkov wrote:
On 01/12/2022 01:51, Kuogee Hsieh wrote:
Move data-lanes property from mdss_dp node to dp_out endpoint. Also
add link-frequencies property into dp_out endpoint as well. The last
frequency specified at link-frequencies will be the max link rate
supported by DP.
Changes in v5:
-- revert changes at sc7180.dtsi and sc7280.dtsi
-- add &dp_out to sc7180-trogdor.dtsi and sc7280-herobrine.dtsi
Changes in v6:
-- add data-lanes and link-frequencies to yaml
Signed-off-by: Kuogee Hsieh <quic_khsieh@xxxxxxxxxxx>
---
.../devicetree/bindings/display/msm/dp-controller.yaml | 17
+++++++++++++++++
Separate patch. Also you didn't check the get_maintainers output, so
required parties were not included into the distribution.
Also as you'd check the get_maintainers output, please fix other
email addresses too.
arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 6 +++++-
arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi | 6 +++++-
3 files changed, 27 insertions(+), 2 deletions(-)
diff --git
a/Documentation/devicetree/bindings/display/msm/dp-controller.yaml
b/Documentation/devicetree/bindings/display/msm/dp-controller.yaml
index 94bc6e1..af70343 100644
--- a/Documentation/devicetree/bindings/display/msm/dp-controller.yaml
+++ b/Documentation/devicetree/bindings/display/msm/dp-controller.yaml
@@ -90,6 +90,20 @@ properties:
$ref: /schemas/graph.yaml#/properties/port
description: Output endpoint of the controller
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+
+ properties:
+ link-frequencies: true
+ data-lanes: true
No. Use $ref for both of them.
+
+ required:
+ - link-frequencies
+ - data-lanes
No, they are not required.
+
+ additionalProperties: false
+
deprecation of old data-lanes property?
required:
- compatible
- reg
@@ -158,6 +172,9 @@ examples:
reg = <1>;
endpoint {
remote-endpoint = <&typec>;
+ data-lanes = <1 2>;
+ link-frequencies = /bits/ 64 <160000000 270000000
s/1600/1620
+ 540000000 810000000>;
I guess the number of zeroes is wrong here. This is 160 MHz ... 810
Mhz, rather than 1.6 GHz ... 8.1 GHz
Ok, I was wrong here. The old code definitely defaults to 570
mega-something. Now I'd really like to read your description for the
link-frequencies property, because the
phy_configure_opts_dp::link_rate is clearly specified in Mb/s and it
takes a fixed set of values from 1.62 Gb/s up to 8.1 Gb/s.
I think the drm_dp_bw_code_to_link_rate() function is incorrect by
itself, as it multiplies with 27000 (27 Mbps) rather than 270000 (0.27
Gbps) as required by the standard. So first, we should fix the
function, then all the rates would become logical.
no, drm_dp_bw_code_to_link_rate() is correct and should not be changes
since it impact to other dp drivers too.
0.27Gbps/lane is specified at DP spec.
DP use 8b/10b coding rule (10 bits symbol contains 8 bits data).
At least it should get documentation that it returns Kylo-bytes per second.
But, getting back to link-frequencies. The documentation clearly says
that it should be allowed data bus _frequencies_. And frequencies are
measured in Hz, not in bits/sec or bytes/sec.
};
};
};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
index 754d2d6..39f0844 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
@@ -812,7 +812,11 @@ hp_i2c: &i2c9 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dp_hot_plug_det>;
- data-lanes = <0 1>;
+};
+
+&dp_out {
+ data-lanes = <0 1>;
+ link-frequencies = /bits/ 64 <160000000 270000000 540000000>;
Same comment here.
};
&pm6150_adc {
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
index 93e39fc..b7c343d 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
@@ -440,7 +440,11 @@ ap_i2c_tpm: &i2c14 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&dp_hot_plug_det>;
- data-lanes = <0 1>;
+};
+
+&dp_out {
+ data-lanes = <0 1>;
+ link-frequencies = /bits/ 64 <160000000 270000000 540000000
810000000>;
And here.
};
&mdss_mdp {
--
With best wishes
Dmitry
