Re: [PATCH v5 1/3] drm/msm/dp: cleared DP_DOWNSPREAD_CTRL register before start link training

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 9/12/2022 12:25 PM, Dmitry Baryshkov wrote:
On 12/09/2022 22:21, Kuogee Hsieh wrote:

On 9/12/2022 11:39 AM, Dmitry Baryshkov wrote:
On 12/09/2022 19:23, Kuogee Hsieh wrote:
DOWNSPREAD_CTRL (0x107) shall be cleared to 0 upon power-on reset or an
upstream device disconnect. This patch will enforce this rule by always
cleared DOWNSPREAD_CTRL register to 0 before start link training. At rare
case that DP MSA timing parameters may be mis-interpreted by the sink
which causes audio sampling rate be calculated wrongly and cause audio
did not work at sink if DOWNSPREAD_CTRL register is not cleared to 0.

Changes in v2:
1) fix spelling at commit text
2) merge ssc variable into encoding[0]

Changes in v3:
-- correct spelling of DOWNSPREAD_CTRL
-- replace err with len of ssize_t

Changes in v4:
-- split into 2 patches

Fixes: 154b5a7da0fd ("drm/msm/dp: add displayPort driver support")

Fixes tag is wrong here. It should be:

Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support")

Signed-off-by: Kuogee Hsieh <quic_khsieh@xxxxxxxxxxx>
---
  drivers/gpu/drm/msm/dp/dp_ctrl.c | 13 +++++--------
  1 file changed, 5 insertions(+), 8 deletions(-)

diff --git a/drivers/gpu/drm/msm/dp/dp_ctrl.c b/drivers/gpu/drm/msm/dp/dp_ctrl.c
index ab6aa13..2c74c59 100644
--- a/drivers/gpu/drm/msm/dp/dp_ctrl.c
+++ b/drivers/gpu/drm/msm/dp/dp_ctrl.c
@@ -1245,8 +1245,7 @@ static int dp_ctrl_link_train(struct dp_ctrl_private *ctrl,
  {
      int ret = 0;
      const u8 *dpcd = ctrl->panel->dpcd;
-    u8 encoding = DP_SET_ANSI_8B10B;
-    u8 ssc;
+    u8 encoding[] = { 0, DP_SET_ANSI_8B10B };
      u8 assr;
      struct dp_link_info link_info = {0};
  @@ -1258,13 +1257,11 @@ static int dp_ctrl_link_train(struct dp_ctrl_private *ctrl,
        dp_aux_link_configure(ctrl->aux, &link_info);
  -    if (drm_dp_max_downspread(dpcd)) {
-        ssc = DP_SPREAD_AMP_0_5;
-        drm_dp_dpcd_write(ctrl->aux, DP_DOWNSPREAD_CTRL, &ssc, 1);
-    }
+    if (drm_dp_max_downspread(dpcd))
+        encoding[0] |= DP_SPREAD_AMP_0_5;

It would be simpler to call drm_dp_dpcd_write(ssc, DP_DOWNSPREAD_CTRL, 1) unconditionally here. You won't have to change the encoding/DP_MAIN_LINK_CHANNEL_CODING_SET/etc.

The difference is one write with 2 bytes against two writes with one byte each.

I think it is more efficient to combine two bytes into one write since these two bytes are consecutive address.

I probably wouldn't do so, nevertheless:

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>



  -    drm_dp_dpcd_write(ctrl->aux, DP_MAIN_LINK_CHANNEL_CODING_SET,
-                &encoding, 1);
+    /* config DOWNSPREAD_CTRL and MAIN_LINK_CHANNEL_CODING_SET */
+    drm_dp_dpcd_write(ctrl->aux, DP_DOWNSPREAD_CTRL, encoding, 2);
        if (drm_dp_alternate_scrambler_reset_cap(dpcd)) {
          assr = DP_ALTERNATE_SCRAMBLER_RESET_ENABLE;





[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux