Re: [PATCH] drm/msm/dp: cleared DP_DOWNSPREAD_CTRL register before start link training

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 





On 9/7/2022 10:21 AM, Kuogee Hsieh wrote:
DOWNSPREAD_CTRL (0x107) shall be cleared to 0 upon power-on reset or an
upstream device disconnect. This patch will enforce this rule by always
cleared DOWNPREAD_CTRL register to 0 before start link training. At rare
case that DP MSA timing parameters may be mis-interpreted by the sinker
sinker--->sink
which causes audio sampling rate be calculated wrongly and cause audio
did not work at sinker if DOWNSPREAD_CTRL register is not cleared to 0.
same here
This patch also make sure bring sinker out of D3 power-down mode into D0
(normal operation mode) successfully by retrying 3 times.

here too
Fixes: 154b5a7da0fd ("drm/msm/dp: add displayPort driver support")
Signed-off-by: Kuogee Hsieh <quic_khsieh@xxxxxxxxxxx>
---
  drivers/gpu/drm/msm/dp/dp_ctrl.c |  5 ++---
  drivers/gpu/drm/msm/dp/dp_link.c | 17 +++++++++++------
  2 files changed, 13 insertions(+), 9 deletions(-)

diff --git a/drivers/gpu/drm/msm/dp/dp_ctrl.c b/drivers/gpu/drm/msm/dp/dp_ctrl.c
index ab6aa13..e864a6e 100644
--- a/drivers/gpu/drm/msm/dp/dp_ctrl.c
+++ b/drivers/gpu/drm/msm/dp/dp_ctrl.c
@@ -1245,7 +1245,7 @@ static int dp_ctrl_link_train(struct dp_ctrl_private *ctrl,
  {
  	int ret = 0;
  	const u8 *dpcd = ctrl->panel->dpcd;
-	u8 encoding = DP_SET_ANSI_8B10B;
+	u8 encoding[2] = {0, DP_SET_ANSI_8B10B};
  	u8 ssc;
  	u8 assr;
  	struct dp_link_info link_info = {0};
@@ -1263,8 +1263,7 @@ static int dp_ctrl_link_train(struct dp_ctrl_private *ctrl,
  		drm_dp_dpcd_write(ctrl->aux, DP_DOWNSPREAD_CTRL, &ssc, 1);
  	}
- drm_dp_dpcd_write(ctrl->aux, DP_MAIN_LINK_CHANNEL_CODING_SET,
-				&encoding, 1);
+	drm_dp_dpcd_write(ctrl->aux, DP_DOWNSPREAD_CTRL, encoding, 2);

This seems wrong.

This will override the value programmed by the above piece of code.

        if (drm_dp_max_downspread(dpcd)) {
                ssc = DP_SPREAD_AMP_0_5;
                drm_dp_dpcd_write(ctrl->aux, DP_DOWNSPREAD_CTRL, &ssc, 1);
        }

Perhaps, you should have an else case to the above if and program 0 only for those cases?

  	if (drm_dp_alternate_scrambler_reset_cap(dpcd)) {
  		assr = DP_ALTERNATE_SCRAMBLER_RESET_ENABLE;
diff --git a/drivers/gpu/drm/msm/dp/dp_link.c b/drivers/gpu/drm/msm/dp/dp_link.c
index 36f0af0..3ad3826 100644
--- a/drivers/gpu/drm/msm/dp/dp_link.c
+++ b/drivers/gpu/drm/msm/dp/dp_link.c
@@ -49,7 +49,7 @@ static int dp_aux_link_power_up(struct drm_dp_aux *aux,
  					struct dp_link_info *link)
  {
  	u8 value;
-	int err;
+	int i, err;
if (link->revision < 0x11)
  		return 0;
@@ -61,11 +61,16 @@ static int dp_aux_link_power_up(struct drm_dp_aux *aux,
  	value &= ~DP_SET_POWER_MASK;
  	value |= DP_SET_POWER_D0;
- err = drm_dp_dpcd_writeb(aux, DP_SET_POWER, value);
-	if (err < 0)
-		return err;
-
-	usleep_range(1000, 2000);
+	/*
+	 * When turning on, we need to retry for 1ms to give the sink
+	 * time to wake up.
+	 */
+	for (i = 0; i < 3; i++) {
+	        err = drm_dp_dpcd_writeb(aux, DP_SET_POWER, value);
+		usleep_range(1000, 2000);
+		if (err == 1)
+			break;
+	}
return 0;
  }



[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux