The Arm PL110 and PL111 are IP blocks that provide a display engine with
an LCD interface, being able to drive a variety of LC panels.
Convert the binding over to DT schema, to the DTs can be automatically
checked.
This still contains the deprecated "arm,pl11x,tft-r0g0b0-pads" property,
because this is used by several DTs in the tree.
Signed-off-by: Andre Przywara <andre.przywara@xxxxxxx>
---
.../devicetree/bindings/display/arm,pl11x.txt | 110 -----------
.../bindings/display/arm,pl11x.yaml | 174 ++++++++++++++++++
2 files changed, 174 insertions(+), 110 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/display/arm,pl11x.txt
create mode 100644 Documentation/devicetree/bindings/display/arm,pl11x.yaml
diff --git a/Documentation/devicetree/bindings/display/arm,pl11x.txt b/Documentation/devicetree/bindings/display/arm,pl11x.txt
deleted file mode 100644
index 3f977e72a2005..0000000000000
--- a/Documentation/devicetree/bindings/display/arm,pl11x.txt
+++ /dev/null
@@ -1,110 +0,0 @@
-* ARM PrimeCell Color LCD Controller PL110/PL111
-
-See also Documentation/devicetree/bindings/arm/primecell.yaml
-
-Required properties:
-
-- compatible: must be one of:
- "arm,pl110", "arm,primecell"
- "arm,pl111", "arm,primecell"
-
-- reg: base address and size of the control registers block
-
-- interrupt-names: either the single entry "combined" representing a
- combined interrupt output (CLCDINTR), or the four entries
- "mbe", "vcomp", "lnbu", "fuf" representing the individual
- CLCDMBEINTR, CLCDVCOMPINTR, CLCDLNBUINTR, CLCDFUFINTR interrupts
-
-- interrupts: contains an interrupt specifier for each entry in
- interrupt-names
-
-- clock-names: should contain "clcdclk" and "apb_pclk"
-
-- clocks: contains phandle and clock specifier pairs for the entries
- in the clock-names property. See
- Documentation/devicetree/bindings/clock/clock-bindings.txt
-
-Optional properties:
-
-- memory-region: phandle to a node describing memory (see
- Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt)
- to be used for the framebuffer; if not present, the framebuffer
- may be located anywhere in the memory
-
-- max-memory-bandwidth: maximum bandwidth in bytes per second that the
- cell's memory interface can handle; if not present, the memory
- interface is fast enough to handle all possible video modes
-
-Required sub-nodes:
-
-- port: describes LCD panel signals, following the common binding
- for video transmitter interfaces; see
- Documentation/devicetree/bindings/media/video-interfaces.txt
-
-Deprecated properties:
- The port's endbpoint subnode had this, now deprecated property
- in the past. Drivers should be able to survive without it:
-
- - arm,pl11x,tft-r0g0b0-pads: an array of three 32-bit values,
- defining the way CLD pads are wired up; first value
- contains index of the "CLD" external pin (pad) used
- as R0 (first bit of the red component), second value
- index of the pad used as G0, third value index of the
- pad used as B0, see also "LCD panel signal multiplexing
- details" paragraphs in the PL110/PL111 Technical
- Reference Manuals; this implicitly defines available
- color modes, for example:
- - PL111 TFT 4:4:4 panel:
- arm,pl11x,tft-r0g0b0-pads = <4 15 20>;
- - PL110 TFT (1:)5:5:5 panel:
- arm,pl11x,tft-r0g0b0-pads = <1 7 13>;
- - PL111 TFT (1:)5:5:5 panel:
- arm,pl11x,tft-r0g0b0-pads = <3 11 19>;
- - PL111 TFT 5:6:5 panel:
- arm,pl11x,tft-r0g0b0-pads = <3 10 19>;
- - PL110 and PL111 TFT 8:8:8 panel:
- arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
- - PL110 and PL111 TFT 8:8:8 panel, R & B components swapped:
- arm,pl11x,tft-r0g0b0-pads = <16 8 0>;
-
-
-Example:
-
- clcd@10020000 {
- compatible = "arm,pl111", "arm,primecell";
- reg = <0x10020000 0x1000>;
- interrupt-names = "combined";
- interrupts = <0 44 4>;
- clocks = <&oscclk1>, <&oscclk2>;
- clock-names = "clcdclk", "apb_pclk";
- max-memory-bandwidth = <94371840>; /* Bps, 1024x768@60 16bpp */
-
- port {
- clcd_pads: endpoint {
- remote-endpoint = <&clcd_panel>;
- };
- };
-
- };
-
- panel {
- compatible = "panel-dpi";
-
- port {
- clcd_panel: endpoint {
- remote-endpoint = <&clcd_pads>;
- };
- };
-
- panel-timing {
- clock-frequency = <25175000>;
- hactive = <640>;
- hback-porch = <40>;
- hfront-porch = <24>;
- hsync-len = <96>;
- vactive = <480>;
- vback-porch = <32>;
- vfront-porch = <11>;
- vsync-len = <2>;
- };
- };
diff --git a/Documentation/devicetree/bindings/display/arm,pl11x.yaml b/Documentation/devicetree/bindings/display/arm,pl11x.yaml
new file mode 100644
index 0000000000000..c17838c197da8
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/arm,pl11x.yaml
@@ -0,0 +1,174 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/arm,pl11x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Arm PrimeCell Color LCD Controller PL110/PL111
+
+maintainers:
+ - Liviu Dudau <Liviu.Dudau@xxxxxxx>
+ - Andre Przywara <andre.przywara@xxxxxxx>
+
+description:
+ The Arm Primcell PL010/PL111 is an LCD controller IP, than scans out
+ a framebuffer region in system memory, and creates timed signals for
+ a variety of LCD panels.
+
+# We need a select here so we don't match all nodes with 'arm,primecell'
+select:
+ properties:
+ compatible:
+ contains:
+ enum:
+ - arm,pl110
+ - arm,pl111
+ required:
+ - compatible
+
+properties:
+ compatible:
+ items:
+ - enum:
+ - arm,pl110
+ - arm,pl111
+ - const: arm,primecell
+
+ reg:
+ maxItems: 1
+
+ interrupt-names:
+ oneOf:
+ - const: combined
+ description:
+ The IP provides four individual interrupt lines, but also one
+ combined line. If the integration only connects this line to the
+ interrupt controller, this single interrupt is noted here.
+ - items:
+ - const: mbe # CLCDMBEINTR
+ - const: vcomp # CLCDVCOMPINTR
+ - const: lnbu # CLCDLNBUINTR
+ - const: fuf # CLCDFUFINTR
+
+ interrupts:
+ minItems: 1
+ maxItems: 4
+
+ clock-names:
+ items:
+ - const: clcdclk
+ - const: apb_pclk
+
+ clocks:
+ items:
+ - description: The CLCDCLK reference clock for the controller.
+ - description: The HCLK AHB slave clock for the register access.
+
+ memory-region:
+ maxItems: 1
+ description:
+ Phandle to a node describing memory to be used for the framebuffer.
+ If not present, the framebuffer may be located anywhere in memory.
+
+ max-memory-bandwidth:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description:
+ Maximum bandwidth in bytes per second that the cell's memory interface
+ can handle.
+ If not present, the memory interface is fast enough to handle all
+ possible video modes.
+
+ port:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ additionalProperties: false
+
+ description:
+ Output endpoint of the controller, connecting the LCD panel signals.
+
+ properties:
+ endpoint:
+ $ref: /schemas/graph.yaml#/$defs/endpoint-base
+ unevaluatedProperties: false
+
+ properties:
+ arm,pl11x,tft-r0g0b0-pads:
+ $ref: /schemas/types.yaml#/definitions/uint32-array
+ items:
+ - description: index of CLD pad used for first red bit (R0)
+ - description: index of CLD pad used for first green bit (G0)
+ - description: index of CLD pad used for first blue bit (G0)
+ deprecated: true
+ description: |
+ DEPRECATED. An array of three 32-bit values, defining the way
+ CLD[23:0] pads are wired up.
+ The first value contains the index of the "CLD" external pin (pad)
+ used as R0 (first bit of the red component), the second value for
+ green, the third value for blue.
+ See also "LCD panel signal multiplexing details" paragraphs in the
+ PL110/PL111 Technical Reference Manuals.
+ This implicitly defines available color modes, for example:
+ - PL111 TFT 4:4:4 panel:
+ arm,pl11x,tft-r0g0b0-pads = <4 15 20>;
+ - PL110 TFT (1:)5:5:5 panel:
+ arm,pl11x,tft-r0g0b0-pads = <1 7 13>;
+ - PL111 TFT (1:)5:5:5 panel:
+ arm,pl11x,tft-r0g0b0-pads = <3 11 19>;
+ - PL111 TFT 5:6:5 panel:
+ arm,pl11x,tft-r0g0b0-pads = <3 10 19>;
+ - PL110 and PL111 TFT 8:8:8 panel:
+ arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
+ - PL110 and PL111 TFT 8:8:8 panel, R & B components swapped:
+ arm,pl11x,tft-r0g0b0-pads = <16 8 0>;
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupt-names
+ - interrupts
+ - clock-names
+ - clocks
+ - port
+
+examples:
+ - |
+ clcd@10020000 {
+ compatible = "arm,pl111", "arm,primecell";
+ reg = <0x10020000 0x1000>;
+ interrupt-names = "combined";
+ interrupts = <44>;
+ clocks = <&oscclk1>, <&oscclk2>;
+ clock-names = "clcdclk", "apb_pclk";
+ max-memory-bandwidth = <94371840>; /* Bps, 1024x768@60 16bpp */
+
+ port {
+ clcd_pads: endpoint {
+ remote-endpoint = <&clcd_panel>;
+ };
+ };
+ };
+
+ panel {
+ compatible = "arm,rtsm-display", "panel-dpi";
+ power-supply = <&vcc_supply>;
+
+ port {
+ clcd_panel: endpoint {
+ remote-endpoint = <&clcd_pads>;
+ };
+ };
+
+ panel-timing {
+ clock-frequency = <25175000>;
+ hactive = <640>;
+ hback-porch = <40>;
+ hfront-porch = <24>;
+ hsync-len = <96>;
+ vactive = <480>;
+ vback-porch = <32>;
+ vfront-porch = <11>;
+ vsync-len = <2>;
+ };
+ };
+...
--
2.25.1
