The Arm HDLCD is a display controller that scans out a framebuffer and
hands a signal to a digital encoder to generate a DVI or HDMI signal.
Convert the existing DT binding to DT schema.
Signed-off-by: Andre Przywara <andre.przywara@xxxxxxx>
---
.../devicetree/bindings/display/arm,hdlcd.txt | 79 ----------------
.../bindings/display/arm,hdlcd.yaml | 91 +++++++++++++++++++
2 files changed, 91 insertions(+), 79 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/display/arm,hdlcd.txt
create mode 100644 Documentation/devicetree/bindings/display/arm,hdlcd.yaml
diff --git a/Documentation/devicetree/bindings/display/arm,hdlcd.txt b/Documentation/devicetree/bindings/display/arm,hdlcd.txt
deleted file mode 100644
index 78bc24296f3e4..0000000000000
--- a/Documentation/devicetree/bindings/display/arm,hdlcd.txt
+++ /dev/null
@@ -1,79 +0,0 @@
-ARM HDLCD
-
-This is a display controller found on several development platforms produced
-by ARM Ltd and in more modern of its' Fast Models. The HDLCD is an RGB
-streamer that reads the data from a framebuffer and sends it to a single
-digital encoder (DVI or HDMI).
-
-Required properties:
- - compatible: "arm,hdlcd"
- - reg: Physical base address and length of the controller's registers.
- - interrupts: One interrupt used by the display controller to notify the
- interrupt controller when any of the interrupt sources programmed in
- the interrupt mask register have activated.
- - clocks: A list of phandle + clock-specifier pairs, one for each
- entry in 'clock-names'.
- - clock-names: A list of clock names. For HDLCD it should contain:
- - "pxlclk" for the clock feeding the output PLL of the controller.
-
-Required sub-nodes:
- - port: The HDLCD connection to an encoder chip. The connection is modeled
- using the OF graph bindings specified in
- Documentation/devicetree/bindings/graph.txt.
-
-Optional properties:
- - memory-region: phandle to a node describing memory (see
- Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) to be
- used for the framebuffer; if not present, the framebuffer may be located
- anywhere in memory.
-
-
-Example:
-
-/ {
- ...
-
- hdlcd@2b000000 {
- compatible = "arm,hdlcd";
- reg = <0 0x2b000000 0 0x1000>;
- interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&oscclk5>;
- clock-names = "pxlclk";
- port {
- hdlcd_output: endpoint@0 {
- remote-endpoint = <&hdmi_enc_input>;
- };
- };
- };
-
- /* HDMI encoder on I2C bus */
- i2c@7ffa0000 {
- ....
- hdmi-transmitter@70 {
- compatible = ".....";
- reg = <0x70>;
- port@0 {
- hdmi_enc_input: endpoint {
- remote-endpoint = <&hdlcd_output>;
- };
-
- hdmi_enc_output: endpoint {
- remote-endpoint = <&hdmi_1_port>;
- };
- };
- };
-
- };
-
- hdmi1: connector@1 {
- compatible = "hdmi-connector";
- type = "a";
- port {
- hdmi_1_port: endpoint {
- remote-endpoint = <&hdmi_enc_output>;
- };
- };
- };
-
- ...
-};
diff --git a/Documentation/devicetree/bindings/display/arm,hdlcd.yaml b/Documentation/devicetree/bindings/display/arm,hdlcd.yaml
new file mode 100644
index 0000000000000..1fe8e07334152
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/arm,hdlcd.yaml
@@ -0,0 +1,91 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/arm,hdlcd.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Arm HDLCD display controller binding
+
+maintainers:
+ - Liviu Dudau <Liviu.Dudau@xxxxxxx>
+ - Andre Przywara <andre.przywara@xxxxxxx>
+
+description: |+
+ The Arm HDLCD is a display controller found on several development platforms
+ produced by ARM Ltd and in more modern of its Fast Models. The HDLCD is an
+ RGB streamer that reads the data from a framebuffer and sends it to a single
+ digital encoder (DVI or HDMI).
+
+properties:
+ compatible:
+ const: arm,hdlcd
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ clock-names:
+ const: pxlclk
+
+ clocks:
+ maxItems: 1
+ description: The input reference for the pixel clock.
+
+ memory-region:
+ maxItems: 1
+ description:
+ Phandle to a node describing memory to be used for the framebuffer.
+ If not present, the framebuffer may be located anywhere in memory.
+
+ iommus:
+ maxItems: 1
+
+ port:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description:
+ Output endpoint of the controller, connecting the LCD panel signals.
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - clocks
+ - port
+
+examples:
+ - |
+ hdlcd@2b000000 {
+ compatible = "arm,hdlcd";
+ reg = <0x2b000000 0x1000>;
+ interrupts = <0 85 4>;
+ clocks = <&oscclk5>;
+ clock-names = "pxlclk";
+ port {
+ hdlcd_output: endpoint {
+ remote-endpoint = <&hdmi_enc_input>;
+ };
+ };
+ };
+
+ /* HDMI encoder on I2C bus */
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ hdmi-transmitter@70 {
+ compatible = "nxp,tda998x";
+ reg = <0x70>;
+ port {
+ hdmi_enc_input: endpoint {
+ remote-endpoint = <&hdlcd_output>;
+ };
+ };
+ };
+
+ };
+
+...
--
2.25.1
