Hi, On Fri, Mar 25, 2022 at 6:41 AM Sankeerth Billakanti (QUIC) <quic_sbillaka@xxxxxxxxxxx> wrote: > > > -----Original Message----- > > From: Doug Anderson <dianders@xxxxxxxxxxxx> > > Sent: Friday, March 18, 2022 10:51 PM > > To: Sankeerth Billakanti (QUIC) <quic_sbillaka@xxxxxxxxxxx> > > Cc: dri-devel <dri-devel@xxxxxxxxxxxxxxxxxxxxx>; linux-arm-msm <linux-arm- > > msm@xxxxxxxxxxxxxxx>; freedreno <freedreno@xxxxxxxxxxxxxxxxxxxxx>; > > LKML <linux-kernel@xxxxxxxxxxxxxxx>; open list:OPEN FIRMWARE AND > > FLATTENED DEVICE TREE BINDINGS <devicetree@xxxxxxxxxxxxxxx>; Rob Clark > > <robdclark@xxxxxxxxx>; Sean Paul <seanpaul@xxxxxxxxxxxx>; Stephen > > Boyd <swboyd@xxxxxxxxxxxx>; quic_kalyant <quic_kalyant@xxxxxxxxxxx>; > > Abhinav Kumar (QUIC) <quic_abhinavk@xxxxxxxxxxx>; Kuogee Hsieh (QUIC) > > <quic_khsieh@xxxxxxxxxxx>; Andy Gross <agross@xxxxxxxxxx>; > > bjorn.andersson@xxxxxxxxxx; Rob Herring <robh+dt@xxxxxxxxxx>; > > krzk+dt@xxxxxxxxxx; Sean Paul <sean@xxxxxxxxxx>; David Airlie > > <airlied@xxxxxxxx>; Daniel Vetter <daniel@xxxxxxxx>; Thierry Reding > > <thierry.reding@xxxxxxxxx>; Sam Ravnborg <sam@xxxxxxxxxxxx>; > > dmitry.baryshkov@xxxxxxxxxx; quic_vproddut <quic_vproddut@xxxxxxxxxxx> > > Subject: Re: [PATCH v5 2/9] arm64: dts: qcom: sc7280: Add support for eDP > > panel on CRD > > > > Hi, > > > > On Wed, Mar 16, 2022 at 10:36 AM Sankeerth Billakanti > > <quic_sbillaka@xxxxxxxxxxx> wrote: > > > > > > Enable support for eDP interface via aux_bus on CRD platform. > > > > > > Signed-off-by: Sankeerth Billakanti <quic_sbillaka@xxxxxxxxxxx> > > > --- > > > > > > Changes in v5: > > > - Change the order of patches > > > - Remove the backlight nodes > > > - Remove the bias setting > > > - Fix compilation issue > > > - Model VREG_EDP_BP for backlight power > > > > > > Changes in v4: > > > - Create new patch for name changes > > > - Remove output-low > > > > > > Changes in v3: > > > - Sort the nodes alphabetically > > > - Use - instead of _ as node names > > > - Place the backlight and panel nodes under root > > > - Change the name of edp_out to mdss_edp_out > > > - Change the names of regulator nodes > > > - Delete unused properties in the board file > > > > > > > > > Changes in v2: > > > - Sort node references alphabetically > > > - Improve readability > > > - Move the pwm pinctrl to pwm node > > > - Move the regulators to root > > > - Define backlight power > > > - Remove dummy regulator node > > > - Cleanup pinctrl definitions > > > > > > arch/arm64/boot/dts/qcom/sc7280-crd.dts | 93 > > > +++++++++++++++++++++++++++++++++ > > > 1 file changed, 93 insertions(+) > > > > At a high level, I'd expect your patch to be based upon Matthias's series, AKA > > the 4 patches from: > > > > https://lore.kernel.org/r/20220316172814.v1.1.I2deda8f2cd6adfbb525a97d8f > > ee008a8477b7b0e@changeid/ > > > > I'll leave it up to you about whether you care to support eDP on the old > > CRD1/2 or just on CRD3. Personally I'd think CRD3 would be enough. > > > > Then, I'd expect your patch to mostly incorporate > > <https://crrev.com/c/3379844>, though that patch was written before aux- > > bus support so the panel would need to go in a different place. > > > > Stephen already gave some comments and basing on Matthias's patches will > > be a pretty big change, so I probably won't comment lots more. > > > > > > I rebased my change on top of Matthias's changes now. We are discussing about the qcard changes internally to understand the way ahead. > I believe all my current changes are localized to the crd-r3 files only for the qyalcomm crd3.1 > > I want to have a different series for c and dt changes to expedite review process. May I separate the c changes from this series? I'd have no problems with that. They go into different trees and if it makes it easier to get a new version of the driver out while you're figuring out what to do about the dts then I'd say let's do it. -Doug
