[PATCH v4 00/13] drm: bridge: icn6211: Fix hard-coded panel settings and add I2C support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



This series fixes multiple problems with the ICN6211 driver and adds
support for configuration of the chip via I2C bus.

First, in the current state, the ICN6211 driver hard-codes DPI timing
and clock settings specific to some unknown panel. The settings provided
by panel driver are ignored. Using any other panel than the one for which
this driver is currently hard-coded can lead to permanent damage of the
panel (per display supplier warning, and it sure did in my case. The
damage looks like multiple rows of dead pixels at the bottom of the
panel, and this is not going away even after long power off time).

Much of this series thus fixes incorrect register layout, DPI timing
programming, clock generation by adding actual PLL configuration code.
This series also adds lane count decoding instead of using hard-coded
value, and fills in a couple of registers with likely correct default
values.

Second, this series adds support for I2C configuration of the ICN6211.
The device can be configured either via DSI command mode or via I2C,
the register layout is the same in both cases.

Since the datasheet for this device is very hard to come by, a lot of
information has been salvaged from [1] and [2].

[1] https://github.com/rockchip-linux/kernel/blob/develop-4.19/drivers/gpu/drm/bridge/icn6211.c
[2] https://github.com/tdjastrzebski/ICN6211-Configurator

Cc: Jagan Teki <jagan@xxxxxxxxxxxxxxxxxxxx>
Cc: Maxime Ripard <maxime@xxxxxxxxxx>
Cc: Robert Foss <robert.foss@xxxxxxxxxx>
Cc: Sam Ravnborg <sam@xxxxxxxxxxxx>
Cc: Thomas Zimmermann <tzimmermann@xxxxxxx>
To: dri-devel@xxxxxxxxxxxxxxxxxxxxx

Marek Vasut (13):
  dt-bindings: display: bridge: icn6211: Document DSI data-lanes
    property
  drm: bridge: icn6211: Fix register layout
  drm: bridge: icn6211: Fix HFP_HSW_HBP_HI and HFP_MIN handling
  drm: bridge: icn6211: Add HS/VS/DE polarity handling
  drm: bridge: icn6211: Add DSI lane count DT property parsing
  drm: bridge: icn6211: Add generic DSI-to-DPI PLL configuration
  drm: bridge: icn6211: Use DSI burst mode without EoT and with LP
    command mode
  drm: bridge: icn6211: Disable DPI color swap
  drm: bridge: icn6211: Set SYS_CTRL_1 to value used in examples
  drm: bridge: icn6211: Implement atomic_get_input_bus_fmts
  drm: bridge: icn6211: Add I2C configuration support
  drm: bridge: icn6211: Rework ICN6211_DSI to chipone_writeb()
  drm: bridge: icn6211: Read and validate chip IDs before configuration

 .../display/bridge/chipone,icn6211.yaml       |  18 +-
 drivers/gpu/drm/bridge/chipone-icn6211.c      | 507 ++++++++++++++++--
 2 files changed, 472 insertions(+), 53 deletions(-)

-- 
2.34.1




[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux