Re: [Intel-gfx] [PATCH v3 4/4] drm/i915: Improve long running OCL w/a for GuC submission

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 09/03/2022 21:16, John Harrison wrote:
On 3/8/2022 01:41, Tvrtko Ursulin wrote:
On 03/03/2022 22:37, John.C.Harrison@xxxxxxxxx wrote:
From: John Harrison <John.C.Harrison@xxxxxxxxx>

A workaround was added to the driver to allow OpenCL workloads to run
'forever' by disabling pre-emption on the RCS engine for Gen12.
It is not totally unbound as the heartbeat will kick in eventually
and cause a reset of the hung engine.

However, this does not work well in GuC submission mode. In GuC mode,
the pre-emption timeout is how GuC detects hung contexts and triggers
a per engine reset. Thus, disabling the timeout means also losing all
per engine reset ability. A full GT reset will still occur when the
heartbeat finally expires, but that is a much more destructive and
undesirable mechanism.

The purpose of the workaround is actually to give OpenCL tasks longer
to reach a pre-emption point after a pre-emption request has been
issued. This is necessary because Gen12 does not support mid-thread
pre-emption and OpenCL can have long running threads.

So, rather than disabling the timeout completely, just set it to a
'long' value.

v2: Review feedback from Tvrtko - must hard code the 'long' value
instead of determining it algorithmically. So make it an extra CONFIG
definition. Also, remove the execlist centric comment from the
existing pre-emption timeout CONFIG option given that it applies to
more than just execlists.

Signed-off-by: John Harrison <John.C.Harrison@xxxxxxxxx>
Reviewed-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@xxxxxxxxx> (v1)
Acked-by: Michal Mrozek <michal.mrozek@xxxxxxxxx>
---
  drivers/gpu/drm/i915/Kconfig.profile      | 26 +++++++++++++++++++----
  drivers/gpu/drm/i915/gt/intel_engine_cs.c |  9 ++++++--
  2 files changed, 29 insertions(+), 6 deletions(-)

diff --git a/drivers/gpu/drm/i915/Kconfig.profile b/drivers/gpu/drm/i915/Kconfig.profile
index 39328567c200..7cc38d25ee5c 100644
--- a/drivers/gpu/drm/i915/Kconfig.profile
+++ b/drivers/gpu/drm/i915/Kconfig.profile
@@ -57,10 +57,28 @@ config DRM_I915_PREEMPT_TIMEOUT
      default 640 # milliseconds
      help
        How long to wait (in milliseconds) for a preemption event to occur -      when submitting a new context via execlists. If the current context -      does not hit an arbitration point and yield to HW before the timer
-      expires, the HW will be reset to allow the more important context
-      to execute.
+      when submitting a new context. If the current context does not hit +      an arbitration point and yield to HW before the timer expires, the
+      HW will be reset to allow the more important context to execute.
+
+      This is adjustable via
+      /sys/class/drm/card?/engine/*/preempt_timeout_ms
+
+      May be 0 to disable the timeout.
+
+      The compiled in default may get overridden at driver probe time on +      certain platforms and certain engines which will be reflected in the
+      sysfs control.
+
+config DRM_I915_PREEMPT_TIMEOUT_COMPUTE
+    int "Preempt timeout for compute engines (ms, jiffy granularity)"
+    default 7500 # milliseconds
+    help
+      How long to wait (in milliseconds) for a preemption event to occur
+      when submitting a new context to a compute capable engine. If the
+      current context does not hit an arbitration point and yield to HW
+      before the timer expires, the HW will be reset to allow the more
+      important context to execute.
          This is adjustable via
        /sys/class/drm/card?/engine/*/preempt_timeout_ms
diff --git a/drivers/gpu/drm/i915/gt/intel_engine_cs.c b/drivers/gpu/drm/i915/gt/intel_engine_cs.c
index 4185c7338581..cc0954ad836a 100644
--- a/drivers/gpu/drm/i915/gt/intel_engine_cs.c
+++ b/drivers/gpu/drm/i915/gt/intel_engine_cs.c
@@ -438,9 +438,14 @@ static int intel_engine_setup(struct intel_gt *gt, enum intel_engine_id id,
      engine->props.timeslice_duration_ms =
          CONFIG_DRM_I915_TIMESLICE_DURATION;
  -    /* Override to uninterruptible for OpenCL workloads. */
+    /*
+     * Mid-thread pre-emption is not available in Gen12. Unfortunately,
+     * some OpenCL workloads run quite long threads. That means they get
+     * reset due to not pre-empting in a timely manner. So, bump the
+     * pre-emption timeout value to be much higher for compute engines.
+     */
      if (GRAPHICS_VER(i915) == 12 && (engine->flags & I915_ENGINE_HAS_RCS_REG_STATE))
-        engine->props.preempt_timeout_ms = 0;
+        engine->props.preempt_timeout_ms = CONFIG_DRM_I915_PREEMPT_TIMEOUT_COMPUTE;

I wouldn't go as far as adding a config option since as it is it only applies to Gen12 but Kconfig text says nothing about that. And I am not saying you should add a Gen12 specific config option, that would be weird. So IMO just drop it.

You were the one arguing that the driver was illegally overriding the user's explicitly chosen settings, including the compile time config

This is a bit out of context and illegally don't think used, so misrepresents the earlier discussion. And I certainly did not suggest a kconfig option.

options. Just having a hardcoded magic number in the driver is the absolute worst kind of override there is.
>
And technically, the config option is not Gen12 specific. It is actually compute specific, hence the name. It just so happens that only Gen12 onwards has compute engines. I can add an extra line to the Kconfig description if you want "NB: compute engines only exist on Gen12 but do include the RCS engine on Gen12".

I am not unconditionally against it but it feels it creates more problems than gives solutions.

In kconfig help you say "compute *capable* engine". Here you say only Gen12 has compute engines. Well before Gen12 render is compute capable, but then how implemented it does not apply which is not good.

Given the runtime override has the only purpose of working around broken hardware then I'd still say to drop it. But if you can come up with help text which won't be misleading and still not overly complicated I am not opposing it.

Regards,

Tvrtko



[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux