Il 18/02/22 11:07, xinlei.lee@xxxxxxxxxxxx ha scritto:
From: Xinlei Lee <xinlei.lee@xxxxxxxxxxxx>
Convert mediatek,dsi.txt to mediatek,dsi.yaml format
Signed-off-by: Xinlei Lee <xinlei.lee@xxxxxxxxxxxx>
---
.../display/mediatek/mediatek,dsi.txt | 62 --------------
.../display/mediatek/mediatek,dsi.yaml | 85 +++++++++++++++++++
2 files changed, 85 insertions(+), 62 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt
create mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.yaml
diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt
deleted file mode 100644
index 36b01458f45c..000000000000
--- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt
+++ /dev/null
@@ -1,62 +0,0 @@
-Mediatek DSI Device
-===================
-
-The Mediatek DSI function block is a sink of the display subsystem and can
-drive up to 4-lane MIPI DSI output. Two DSIs can be synchronized for dual-
-channel output.
-
-Required properties:
-- compatible: "mediatek,<chip>-dsi"
-- the supported chips are mt2701, mt7623, mt8167, mt8173 and mt8183.
-- reg: Physical base address and length of the controller's registers
-- interrupts: The interrupt signal from the function block.
-- clocks: device clocks
- See Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
-- clock-names: must contain "engine", "digital", and "hs"
-- phys: phandle link to the MIPI D-PHY controller.
-- phy-names: must contain "dphy"
-- port: Output port node with endpoint definitions as described in
- Documentation/devicetree/bindings/graph.txt. This port should be connected
- to the input port of an attached DSI panel or DSI-to-eDP encoder chip.
-
-Optional properties:
-- resets: list of phandle + reset specifier pair, as described in [1].
-
-[1] Documentation/devicetree/bindings/reset/reset.txt
-
-MIPI TX Configuration Module
-============================
-
-See phy/mediatek,dsi-phy.yaml
-
-Example:
-
-mipi_tx0: mipi-dphy@10215000 {
- compatible = "mediatek,mt8173-mipi-tx";
- reg = <0 0x10215000 0 0x1000>;
- clocks = <&clk26m>;
- clock-output-names = "mipi_tx0_pll";
- #clock-cells = <0>;
- #phy-cells = <0>;
- drive-strength-microamp = <4600>;
- nvmem-cells= <&mipi_tx_calibration>;
- nvmem-cell-names = "calibration-data";
-};
-
-dsi0: dsi@1401b000 {
- compatible = "mediatek,mt8173-dsi";
- reg = <0 0x1401b000 0 0x1000>;
- interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_LOW>;
- clocks = <&mmsys MM_DSI0_ENGINE>, <&mmsys MM_DSI0_DIGITAL>,
- <&mipi_tx0>;
- clock-names = "engine", "digital", "hs";
- resets = <&mmsys MT8173_MMSYS_SW0_RST_B_DISP_DSI0>;
- phys = <&mipi_tx0>;
- phy-names = "dphy";
-
- port {
- dsi0_out: endpoint {
- remote-endpoint = <&panel_in>;
- };
- };
-};
diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.yaml b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.yaml
new file mode 100644
index 000000000000..552a013786fe
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.yaml
@@ -0,0 +1,85 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/mediatek/mediatek,dsi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: mediatek DSI Controller Device Tree Bindings
Shouldn't this be "MediaTek"?
+
+maintainers:
+ - CK Hu <ck.hu@xxxxxxxxxxxx>
+ - Jitao Shi <jitao.shi@xxxxxxxxxxxx>
+ - Xinlei Lee <xinlei.lee@xxxxxxxxxxxx>
+
+properties:
+ compatible:
+ enum:
+ - mediatek,mt2701-dsi
+ - mediatek,mt8173-dsi
+ - mediatek,mt8183-dsi
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ power-domains:
+ maxItems: 1
+
+ clocks:
+ items:
+ - description: Engine Clock
+ - description: Digital Clock
+ - description: Hs Clock
HS should be all capital letters.
+
+ clock-names:
+ items:
+ - const: engine
+ - const: digital
+ - const: hs
+
+ resets:
+ maxItems: 1
+
+ phys:
+ maxItems: 1
+
+ phy-names:
+ items:
+ - const: dphy
Add #address-cells, #size-cells with const 2
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - power-domains
+ - clocks
+ - clock-names
+ - phys
+ - phy-names
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/mt8183-clk.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+ #include <dt-bindings/power/mt8183-power.h>
+ #include <dt-bindings/phy/phy.h>
+ #include <dt-bindings/reset/mt8183-resets.h>
+
Since all users are using two address and size cells:
soc {
#address-cells = <2>;
#size-cells = <2>;
dsi0: dsi@14014000 {
compatible = "mediatek,mt8183-dsi";
reg = <0 0x14014000 0 0x1000>;
.....etc.....
};
};
+ dsi0: dsi@14014000 {
+ compatible = "mediatek,mt8183-dsi";
+ reg = <0x14014000 0x1000>;
+ interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&spm MT8183_POWER_DOMAIN_DISP>;
+ clocks = <&mmsys CLK_MM_DSI0_MM>,
+ <&mmsys CLK_MM_DSI0_IF>,
+ <&mipi_tx0>;
+ clock-names = "engine", "digital", "hs";
+ resets = <&mmsys MT8183_MMSYS_SW0_RST_B_DISP_DSI0>;
+ phys = <&mipi_tx0>;
+ phy-names = "dphy";
+ };
