The TC358767/TC358867/TC9595 are all capable of operating in multiple
modes, DPI-to-(e)DP, DSI-to-(e)DP, DSI-to-DPI. Add support for the
DSI-to-DPI mode.
This requires skipping most of the (e)DP initialization code, which is
currently a large part of this driver, hence it is better to have far
simpler separate tc_dpi_bridge_funcs and their implementation.
The configuration of DPI output is also much simpler. The configuration
of the DSI input is rather similar to the other TC bridge chips.
The Pixel PLL in DPI output mode does not have the 65..150 MHz limitation
imposed on the (e)DP output mode, so this limitation is skipped to permit
operating panels with far slower pixel clock, even below 9 MHz. This mode
of operation of the PLL is valid and tested.
The detection of bridge mode is now added into tc_probe_bridge_mode(),
where in case a DPI panel is found on port@1 endpoint@1, the mode is
assumed to be DSI-to-DPI. If (e)DP is detected on port@2, the mode is
assumed to be DPI-to-(e)DP.
The DSI-to-(e)DP mode is not supported due to lack of proper hardware,
but this would be some sort of mix between the two aforementioned modes.
Signed-off-by: Marek Vasut <marex@xxxxxxx>
Cc: Jonas Karlman <jonas@xxxxxxxxx>
Cc: Laurent Pinchart <Laurent.pinchart@xxxxxxxxxxxxxxxx>
Cc: Maxime Ripard <maxime@xxxxxxxxxx>
Cc: Neil Armstrong <narmstrong@xxxxxxxxxxxx>
Cc: Sam Ravnborg <sam@xxxxxxxxxxxx>
---
V2: - Rebase on next-20220217 and new patches in this series
---
drivers/gpu/drm/bridge/tc358767.c | 339 +++++++++++++++++++++++++++++-
1 file changed, 332 insertions(+), 7 deletions(-)
diff --git a/drivers/gpu/drm/bridge/tc358767.c b/drivers/gpu/drm/bridge/tc358767.c
index 091c969a36ab7..2b9fceb1333fa 100644
--- a/drivers/gpu/drm/bridge/tc358767.c
+++ b/drivers/gpu/drm/bridge/tc358767.c
@@ -1,6 +1,12 @@
// SPDX-License-Identifier: GPL-2.0-or-later
/*
- * tc358767 eDP bridge driver
+ * TC358767/TC358867/TC9595 DSI/DPI-to-DPI/(e)DP bridge driver
+ *
+ * The TC358767/TC358867/TC9595 can operate in multiple modes.
+ * The following modes are supported:
+ * DPI->(e)DP -- supported
+ * DSI->DPI .... supported
+ * DSI->(e)DP .. NOT supported
*
* Copyright (C) 2016 CogentEmbedded Inc
* Author: Andrey Gusakov <andrey.gusakov@xxxxxxxxxxxxxxxxxx>
@@ -29,6 +35,7 @@
#include <drm/drm_bridge.h>
#include <drm/dp/drm_dp_helper.h>
#include <drm/drm_edid.h>
+#include <drm/drm_mipi_dsi.h>
#include <drm/drm_of.h>
#include <drm/drm_panel.h>
#include <drm/drm_print.h>
@@ -36,7 +43,35 @@
/* Registers */
-/* Display Parallel Interface */
+/* PPI layer registers */
+#define PPI_STARTPPI 0x0104 /* START control bit */
+#define PPI_LPTXTIMECNT 0x0114 /* LPTX timing signal */
+#define LPX_PERIOD 3
+#define PPI_LANEENABLE 0x0134
+#define PPI_TX_RX_TA 0x013c
+#define TTA_GET 0x40000
+#define TTA_SURE 6
+#define PPI_D0S_ATMR 0x0144
+#define PPI_D1S_ATMR 0x0148
+#define PPI_D0S_CLRSIPOCOUNT 0x0164 /* Assertion timer for Lane 0 */
+#define PPI_D1S_CLRSIPOCOUNT 0x0168 /* Assertion timer for Lane 1 */
+#define PPI_D2S_CLRSIPOCOUNT 0x016c /* Assertion timer for Lane 2 */
+#define PPI_D3S_CLRSIPOCOUNT 0x0170 /* Assertion timer for Lane 3 */
+#define PPI_START_FUNCTION BIT(0)
+
+/* DSI layer registers */
+#define DSI_STARTDSI 0x0204 /* START control bit of DSI-TX */
+#define DSI_LANEENABLE 0x0210 /* Enables each lane */
+#define DSI_RX_START BIT(0)
+
+/* Lane enable PPI and DSI register bits */
+#define LANEENABLE_CLEN BIT(0)
+#define LANEENABLE_L0EN BIT(1)
+#define LANEENABLE_L1EN BIT(2)
+#define LANEENABLE_L2EN BIT(1)
+#define LANEENABLE_L3EN BIT(2)
+
+/* Display Parallel Input Interface */
#define DPIPXLFMT 0x0440
#define VS_POL_ACTIVE_LOW (1 << 10)
#define HS_POL_ACTIVE_LOW (1 << 9)
@@ -48,6 +83,14 @@
#define DPI_BPP_RGB666 (1 << 0)
#define DPI_BPP_RGB565 (2 << 0)
+/* Display Parallel Output Interface */
+#define POCTRL 0x0448
+#define POCTRL_S2P BIT(7)
+#define POCTRL_PCLK_POL BIT(3)
+#define POCTRL_VS_POL BIT(2)
+#define POCTRL_HS_POL BIT(1)
+#define POCTRL_DE_POL BIT(0)
+
/* Video Path */
#define VPCTRL0 0x0450
#define VSDELAY GENMASK(31, 20)
@@ -247,6 +290,9 @@ struct tc_data {
struct drm_bridge *panel_bridge;
struct drm_connector connector;
+ struct mipi_dsi_device *dsi;
+ u8 dsi_lanes;
+
/* link settings */
struct tc_edp_link link;
@@ -502,8 +548,10 @@ static int tc_pxl_pll_en(struct tc_data *tc, u32 refclk, u32 pixelclock)
/*
* refclk * mul / (ext_pre_div * pre_div)
* should be in the 150 to 650 MHz range
+ * for (e)DP
*/
- if ((clk > 650000000) || (clk < 150000000))
+ if ((tc->bridge.type != DRM_MODE_CONNECTOR_DPI) &&
+ ((clk > 650000000) || (clk < 150000000)))
continue;
clk = clk / ext_div[i_post];
@@ -820,6 +868,20 @@ static int tc_set_common_video_mode(struct tc_data *tc,
return ret;
}
+static int tc_set_dpi_video_mode(struct tc_data *tc,
+ const struct drm_display_mode *mode)
+{
+ u32 value = POCTRL_S2P;
+
+ if (tc->mode.flags & DRM_MODE_FLAG_NHSYNC)
+ value |= POCTRL_HS_POL;
+
+ if (tc->mode.flags & DRM_MODE_FLAG_NVSYNC)
+ value |= POCTRL_VS_POL;
+
+ return regmap_write(tc->regmap, POCTRL, value);
+}
+
static int tc_set_edp_video_mode(struct tc_data *tc,
const struct drm_display_mode *mode)
{
@@ -1192,6 +1254,79 @@ static int tc_main_link_disable(struct tc_data *tc)
return regmap_write(tc->regmap, DP0CTL, 0);
}
+static int tc_dpi_stream_enable(struct tc_data *tc)
+{
+ int ret;
+ u32 value;
+
+ dev_dbg(tc->dev, "enable video stream\n");
+
+ /* Setup PLL */
+ ret = tc_set_syspllparam(tc);
+ if (ret)
+ return ret;
+
+ /* Pixel PLL must always be enabled for DPI mode */
+ ret = tc_pxl_pll_en(tc, clk_get_rate(tc->refclk),
+ 1000 * tc->mode.clock);
+ if (ret)
+ return ret;
+
+ regmap_write(tc->regmap, PPI_D0S_CLRSIPOCOUNT, 3);
+ regmap_write(tc->regmap, PPI_D1S_CLRSIPOCOUNT, 3);
+ regmap_write(tc->regmap, PPI_D2S_CLRSIPOCOUNT, 3);
+ regmap_write(tc->regmap, PPI_D3S_CLRSIPOCOUNT, 3);
+ regmap_write(tc->regmap, PPI_D0S_ATMR, 0);
+ regmap_write(tc->regmap, PPI_D1S_ATMR, 0);
+ regmap_write(tc->regmap, PPI_TX_RX_TA, TTA_GET | TTA_SURE);
+ regmap_write(tc->regmap, PPI_LPTXTIMECNT, LPX_PERIOD);
+
+ value = ((LANEENABLE_L0EN << tc->dsi_lanes) - LANEENABLE_L0EN) |
+ LANEENABLE_CLEN;
+ regmap_write(tc->regmap, PPI_LANEENABLE, value);
+ regmap_write(tc->regmap, DSI_LANEENABLE, value);
+
+ ret = tc_set_common_video_mode(tc, &tc->mode);
+ if (ret)
+ return ret;
+
+ ret = tc_set_dpi_video_mode(tc, &tc->mode);
+ if (ret)
+ return ret;
+
+ /* Set input interface */
+ value = DP0_AUDSRC_NO_INPUT;
+ if (tc_test_pattern)
+ value |= DP0_VIDSRC_COLOR_BAR;
+ else
+ value |= DP0_VIDSRC_DSI_RX;
+ ret = regmap_write(tc->regmap, SYSCTRL, value);
+ if (ret)
+ return ret;
+
+ msleep(100);
+
+ regmap_write(tc->regmap, PPI_STARTPPI, PPI_START_FUNCTION);
+ regmap_write(tc->regmap, DSI_STARTDSI, DSI_RX_START);
+
+ return 0;
+}
+
+static int tc_dpi_stream_disable(struct tc_data *tc)
+{
+ int ret;
+
+ dev_dbg(tc->dev, "disable video stream\n");
+
+ ret = regmap_update_bits(tc->regmap, DP0CTL, VID_EN, 0);
+ if (ret)
+ return ret;
+
+ tc_pxl_pll_dis(tc);
+
+ return 0;
+}
+
static int tc_edp_stream_enable(struct tc_data *tc)
{
int ret;
@@ -1323,6 +1458,40 @@ static int tc_hardware_init(struct tc_data *tc)
return 0;
}
+static void
+tc_dpi_bridge_atomic_enable(struct drm_bridge *bridge,
+ struct drm_bridge_state *old_bridge_state)
+
+{
+ struct tc_data *tc = bridge_to_tc(bridge);
+ int ret;
+
+ ret = tc_hardware_init(tc);
+ if (ret < 0) {
+ dev_err(tc->dev, "failed to initialize bridge: %d\n", ret);
+ return;
+ }
+
+ ret = tc_dpi_stream_enable(tc);
+ if (ret < 0) {
+ dev_err(tc->dev, "main link stream start error: %d\n", ret);
+ tc_main_link_disable(tc);
+ return;
+ }
+}
+
+static void
+tc_dpi_bridge_atomic_disable(struct drm_bridge *bridge,
+ struct drm_bridge_state *old_bridge_state)
+{
+ struct tc_data *tc = bridge_to_tc(bridge);
+ int ret;
+
+ ret = tc_dpi_stream_disable(tc);
+ if (ret < 0)
+ dev_err(tc->dev, "main link stream stop error: %d\n", ret);
+}
+
static void
tc_edp_bridge_atomic_enable(struct drm_bridge *bridge,
struct drm_bridge_state *old_bridge_state)
@@ -1399,6 +1568,16 @@ static int tc_edp_common_atomic_check(struct drm_bridge *bridge,
return 0;
}
+static int tc_dpi_atomic_check(struct drm_bridge *bridge,
+ struct drm_bridge_state *bridge_state,
+ struct drm_crtc_state *crtc_state,
+ struct drm_connector_state *conn_state)
+{
+ /* DSI->DPI interface clock limitation: upto 100 MHz */
+ return tc_edp_common_atomic_check(bridge, bridge_state, crtc_state,
+ conn_state, 100000);
+}
+
static int tc_edp_atomic_check(struct drm_bridge *bridge,
struct drm_bridge_state *bridge_state,
struct drm_crtc_state *crtc_state,
@@ -1409,6 +1588,18 @@ static int tc_edp_atomic_check(struct drm_bridge *bridge,
conn_state, 154000);
}
+static enum drm_mode_status
+tc_dpi_mode_valid(struct drm_bridge *bridge,
+ const struct drm_display_info *info,
+ const struct drm_display_mode *mode)
+{
+ /* DPI interface clock limitation: upto 100 MHz */
+ if (mode->clock > 100000)
+ return MODE_CLOCK_HIGH;
+
+ return MODE_OK;
+}
+
static enum drm_mode_status
tc_edp_mode_valid(struct drm_bridge *bridge,
const struct drm_display_info *info,
@@ -1520,6 +1711,18 @@ static const struct drm_connector_funcs tc_connector_funcs = {
.atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
};
+static int tc_dpi_bridge_attach(struct drm_bridge *bridge,
+ enum drm_bridge_attach_flags flags)
+{
+ struct tc_data *tc = bridge_to_tc(bridge);
+
+ if (!tc->panel_bridge)
+ return 0;
+
+ return drm_bridge_attach(tc->bridge.encoder, tc->panel_bridge,
+ &tc->bridge, flags);
+}
+
static int tc_edp_bridge_attach(struct drm_bridge *bridge,
enum drm_bridge_attach_flags flags)
{
@@ -1578,6 +1781,45 @@ static void tc_edp_bridge_detach(struct drm_bridge *bridge)
drm_dp_aux_unregister(&bridge_to_tc(bridge)->aux);
}
+#define MAX_INPUT_SEL_FORMATS 1
+
+static u32 *
+tc_dpi_atomic_get_input_bus_fmts(struct drm_bridge *bridge,
+ struct drm_bridge_state *bridge_state,
+ struct drm_crtc_state *crtc_state,
+ struct drm_connector_state *conn_state,
+ u32 output_fmt,
+ unsigned int *num_input_fmts)
+{
+ u32 *input_fmts;
+
+ *num_input_fmts = 0;
+
+ input_fmts = kcalloc(MAX_INPUT_SEL_FORMATS, sizeof(*input_fmts),
+ GFP_KERNEL);
+ if (!input_fmts)
+ return NULL;
+
+ /* This is the DSI-end bus format */
+ input_fmts[0] = MEDIA_BUS_FMT_RGB888_1X24;
+ *num_input_fmts = 1;
+
+ return input_fmts;
+}
+
+static const struct drm_bridge_funcs tc_dpi_bridge_funcs = {
+ .attach = tc_dpi_bridge_attach,
+ .mode_valid = tc_dpi_mode_valid,
+ .mode_set = tc_bridge_mode_set,
+ .atomic_check = tc_dpi_atomic_check,
+ .atomic_enable = tc_dpi_bridge_atomic_enable,
+ .atomic_disable = tc_dpi_bridge_atomic_disable,
+ .atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
+ .atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
+ .atomic_reset = drm_atomic_helper_bridge_reset,
+ .atomic_get_input_bus_fmts = tc_dpi_atomic_get_input_bus_fmts,
+};
+
static const struct drm_bridge_funcs tc_bridge_funcs = {
.attach = tc_edp_bridge_attach,
.detach = tc_edp_bridge_detach,
@@ -1678,6 +1920,81 @@ static irqreturn_t tc_irq_handler(int irq, void *arg)
return IRQ_HANDLED;
}
+static int tc_mipi_dsi_host_attach(struct tc_data *tc)
+{
+ struct device *dev = tc->dev;
+ struct device_node *host_node;
+ struct device_node *endpoint;
+ struct mipi_dsi_device *dsi;
+ struct mipi_dsi_host *host;
+ const struct mipi_dsi_device_info info = {
+ .type = "tc358767",
+ .channel = 0,
+ .node = NULL,
+ };
+ int ret;
+
+ endpoint = of_graph_get_endpoint_by_regs(dev->of_node, 0, 0);
+ tc->dsi_lanes = of_property_count_u32_elems(endpoint, "data-lanes");
+ host_node = of_graph_get_remote_port_parent(endpoint);
+ host = of_find_mipi_dsi_host_by_node(host_node);
+ of_node_put(host_node);
+ of_node_put(endpoint);
+
+ if (tc->dsi_lanes < 0 || tc->dsi_lanes > 4)
+ return -EINVAL;
+
+ if (!host)
+ return -EPROBE_DEFER;
+
+ dsi = mipi_dsi_device_register_full(host, &info);
+ if (IS_ERR(dsi))
+ return dev_err_probe(dev, PTR_ERR(dsi),
+ "failed to create dsi device\n");
+
+ tc->dsi = dsi;
+
+ dsi->lanes = tc->dsi_lanes;
+ dsi->format = MIPI_DSI_FMT_RGB888;
+ dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
+
+ ret = mipi_dsi_attach(dsi);
+ if (ret < 0) {
+ dev_err(dev, "failed to attach dsi to host: %d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int tc_probe_dpi_bridge_endpoint(struct tc_data *tc)
+{
+ struct device *dev = tc->dev;
+ struct drm_panel *panel;
+ int ret;
+
+ /* port@1 is the DPI input/output port */
+ ret = drm_of_find_panel_or_bridge(dev->of_node, 1, 0, &panel, NULL);
+ if (ret && ret != -ENODEV)
+ return ret;
+
+ if (panel) {
+ struct drm_bridge *panel_bridge;
+
+ panel_bridge = devm_drm_panel_bridge_add(dev, panel);
+ if (IS_ERR(panel_bridge))
+ return PTR_ERR(panel_bridge);
+
+ tc->panel_bridge = panel_bridge;
+ tc->bridge.type = DRM_MODE_CONNECTOR_DPI;
+ tc->bridge.funcs = &tc_dpi_bridge_funcs;
+
+ return 0;
+ }
+
+ return ret;
+}
+
static int tc_probe_edp_bridge_endpoint(struct tc_data *tc)
{
struct device *dev = tc->dev;
@@ -1745,7 +2062,7 @@ static int tc_probe_bridge_endpoint(struct tc_data *tc)
if (mode == mode_dpi_to_edp)
return tc_probe_edp_bridge_endpoint(tc);
else if (mode == mode_dsi_to_dpi)
- dev_warn(dev, "The mode DSI-to-DPI is not supported!\n");
+ return tc_probe_dpi_bridge_endpoint(tc);
else if (mode == mode_dsi_to_edp)
dev_warn(dev, "The mode DSI-to-(e)DP is not supported!\n");
else
@@ -1828,15 +2145,23 @@ static int tc_probe(struct i2c_client *client, const struct i2c_device_id *id)
tc->have_irq = true;
}
- ret = tc_aux_link_setup(tc);
- if (ret)
- return ret;
+ if (tc->bridge.type != DRM_MODE_CONNECTOR_DPI) { /* (e)DP output */
+ ret = tc_aux_link_setup(tc);
+ if (ret)
+ return ret;
+ }
tc->bridge.of_node = dev->of_node;
drm_bridge_add(&tc->bridge);
i2c_set_clientdata(client, tc);
+ if (tc->bridge.type == DRM_MODE_CONNECTOR_DPI) { /* DPI output */
+ ret = tc_mipi_dsi_host_attach(tc);
+ if (ret)
+ return ret;
+ }
+
return 0;
}
--
2.34.1
