On Mon, 27 Sept 2021 at 00:42, Dmitry Osipenko <digetx@xxxxxxxxx> wrote:
>
> Add runtime power management and support generic power domains.
>
> Tested-by: Peter Geis <pgwipeout@xxxxxxxxx> # Ouya T30
> Tested-by: Paul Fertser <fercerpav@xxxxxxxxx> # PAZ00 T20
> Tested-by: Nicolas Chauvet <kwizart@xxxxxxxxx> # PAZ00 T20 and TK1 T124
> Tested-by: Matt Merhar <mattmerhar@xxxxxxxxxxxxxx> # Ouya T30
> Signed-off-by: Dmitry Osipenko <digetx@xxxxxxxxx>
> ---
> drivers/gpu/drm/tegra/gr3d.c | 388 ++++++++++++++++++++++++++++++-----
[...]
> +
> +static int gr3d_probe(struct platform_device *pdev)
> +{
> + struct host1x_syncpt **syncpts;
> + struct gr3d *gr3d;
> + unsigned int i;
> + int err;
> +
> + gr3d = devm_kzalloc(&pdev->dev, sizeof(*gr3d), GFP_KERNEL);
> + if (!gr3d)
> + return -ENOMEM;
> +
> + platform_set_drvdata(pdev, gr3d);
> +
> + gr3d->soc = of_device_get_match_data(&pdev->dev);
> +
> + syncpts = devm_kzalloc(&pdev->dev, sizeof(*syncpts), GFP_KERNEL);
> + if (!syncpts)
> + return -ENOMEM;
> +
> + err = gr3d_get_clocks(&pdev->dev, gr3d);
> + if (err)
> + return err;
> +
> + err = gr3d_get_resets(&pdev->dev, gr3d);
> + if (err)
> + return err;
> +
> + err = gr3d_init_power(&pdev->dev, gr3d);
> + if (err)
> + return err;
> +
> INIT_LIST_HEAD(&gr3d->client.base.list);
> gr3d->client.base.ops = &gr3d_client_ops;
> gr3d->client.base.dev = &pdev->dev;
> @@ -352,20 +552,36 @@ static int gr3d_probe(struct platform_device *pdev)
> gr3d->client.version = gr3d->soc->version;
> gr3d->client.ops = &gr3d_ops;
>
> + pm_runtime_enable(&pdev->dev);
> + pm_runtime_use_autosuspend(&pdev->dev);
> + pm_runtime_set_autosuspend_delay(&pdev->dev, 200);
> +
> + err = devm_pm_opp_register_set_opp_helper(&pdev->dev, gr3d_set_opp);
> + if (err)
> + goto disable_rpm;
> +
> + err = devm_tegra_core_dev_init_opp_table_common(&pdev->dev);
> + if (err)
> + goto disable_rpm;
> +
> err = host1x_client_register(&gr3d->client.base);
> if (err < 0) {
> dev_err(&pdev->dev, "failed to register host1x client: %d\n",
> err);
> - return err;
> + goto disable_rpm;
> }
>
> /* initialize address register map */
> for (i = 0; i < ARRAY_SIZE(gr3d_addr_regs); i++)
> set_bit(gr3d_addr_regs[i], gr3d->addr_regs);
>
> - platform_set_drvdata(pdev, gr3d);
> -
> return 0;
> +
> +disable_rpm:
> + pm_runtime_dont_use_autosuspend(&pdev->dev);
> + pm_runtime_disable(&pdev->dev);
Similar comment as for patch13.
> +
> + return err;
> }
>
> static int gr3d_remove(struct platform_device *pdev)
> @@ -380,23 +596,83 @@ static int gr3d_remove(struct platform_device *pdev)
> return err;
> }
>
> - if (gr3d->clk_secondary) {
> - reset_control_assert(gr3d->rst_secondary);
> - tegra_powergate_power_off(TEGRA_POWERGATE_3D1);
> - clk_disable_unprepare(gr3d->clk_secondary);
> + pm_runtime_dont_use_autosuspend(&pdev->dev);
> + pm_runtime_disable(&pdev->dev);
Similar comment as for patch13. You may want to use
pm_runtime_force_suspend() in favor of pm_runtime_disable().
> +
> + return 0;
> +}
[...]
I was looking for a call to dev_pm_opp_set_rate(), but couldn't find
it. Isn't that needed when changing the rate of the clock?
Kind regards
Uffe
