Re: [PATCH v3 05/16] drm/panel-simple-edp: Split eDP panels out of panel-simple

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Douglas,

On Wed, Sep 01, 2021 at 01:19:23PM -0700, Douglas Anderson wrote:
> The panel-simple driver handles way too much. Let's start trying to
> get a handle on it by splitting out the eDP panels. This patch does
> this:
> 
> 1. Start by copying simple-panel verbatim over to a new driver,
>    simple-panel-edp.
> 2. Rename "panel_simple" to "panel_edp" in the new driver.
> 3. Keep only panels marked with `DRM_MODE_CONNECTOR_eDP` in the new
>    driver. Remove those panels from the old driver.
> 4. Remove all recent "DP AUX bus" stuff from the old driver. The DP
>    AUX bus is only possible on DP panels.
> 5. Remove all DSI / MIPI related functions from the new driver.
> 6. Remove bus_format / bus_flags from eDP driver. These things don't
>    seem to make any sense for eDP panels so let's stop filling in made
>    up stuff.
> 
> In the end we end up with a bunch of duplicated code for now. Future
> patches will try to address _some_ of this duplicated code though some
> of it will be unavoidable.
> 
> NOTE: This may not actually move all eDP panels over to the new driver
> since not all panels were properly marked with
> `DRM_MODE_CONNECTOR_eDP`. A future patch will attempt to move wayward
> panels I could identify but even so there may be some missed.
> 
> Suggested-by: Sam Ravnborg <sam@xxxxxxxxxxxx>
> Signed-off-by: Douglas Anderson <dianders@xxxxxxxxxxxx>
> ---
> I believe this is what Sam was looking for when he requested that the
> eDP panels split out [1]. Please yell if not.
I will yell a big thanks! This was exactly what I hoped to see.
And very nice to have panel-simple complexity reduced.
The code duplication is worth it.

To avoid confusion I would prefer the file named panel-edp.c,
as this is not "simple" panels and it then matches the compatible.

A few nits in the following.

	Sam


> 
> [1] https://lore.kernel.org/dri-devel/YRTsFNTn%2FT8fLxyB@xxxxxxxxxxxx/
> 
> Changes in v3:
> - Split eDP panels patch new for v3.
> 
>  drivers/gpu/drm/panel/Kconfig            |   16 +-
>  drivers/gpu/drm/panel/Makefile           |    1 +
>  drivers/gpu/drm/panel/panel-simple-edp.c | 1298 ++++++++++++++++++++++
>  drivers/gpu/drm/panel/panel-simple.c     |  575 +---------
>  4 files changed, 1323 insertions(+), 567 deletions(-)
>  create mode 100644 drivers/gpu/drm/panel/panel-simple-edp.c
> 
> diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
> index 0b3784941312..4b7ff4ebdc34 100644
> --- a/drivers/gpu/drm/panel/Kconfig
> +++ b/drivers/gpu/drm/panel/Kconfig
> @@ -77,14 +77,26 @@ config DRM_PANEL_LVDS
>  	  backlight handling if the panel is attached to a backlight controller.
>  
>  config DRM_PANEL_SIMPLE
> -	tristate "support for simple panels"
> +	tristate "support for simple panels (other than eDP ones)"
> +	depends on OF
> +	depends on BACKLIGHT_CLASS_DEVICE
> +	depends on PM
> +	select VIDEOMODE_HELPERS
> +	help
> +	  DRM panel driver for dumb non-eDP panels that need at most a regulator
> +	  and a GPIO to be powered up. Optionally a backlight can be attached so
> +	  that it can be automatically turned off when the panel goes into a
> +	  low power state.
> +
> +config DRM_PANEL_SIMPLE_EDP

So this should also be named DRM_PANEL_EDP to follow the name of the
driver.

> +	tristate "support for simple Embedded DisplayPort panels"
>  	depends on OF
>  	depends on BACKLIGHT_CLASS_DEVICE
>  	depends on PM
>  	select VIDEOMODE_HELPERS
>  	select DRM_DP_AUX_BUS
>  	help
> -	  DRM panel driver for dumb panels that need at most a regulator and
> +	  DRM panel driver for dumb eDP panels that need at most a regulator and
>  	  a GPIO to be powered up. Optionally a backlight can be attached so
>  	  that it can be automatically turned off when the panel goes into a
>  	  low power state.
> diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
> index 60c0149fc54a..640234d4d693 100644
> --- a/drivers/gpu/drm/panel/Makefile
> +++ b/drivers/gpu/drm/panel/Makefile
> @@ -7,6 +7,7 @@ obj-$(CONFIG_DRM_PANEL_BOE_TV101WUM_NL6) += panel-boe-tv101wum-nl6.o
>  obj-$(CONFIG_DRM_PANEL_DSI_CM) += panel-dsi-cm.o
>  obj-$(CONFIG_DRM_PANEL_LVDS) += panel-lvds.o
>  obj-$(CONFIG_DRM_PANEL_SIMPLE) += panel-simple.o
> +obj-$(CONFIG_DRM_PANEL_SIMPLE_EDP) += panel-simple-edp.o
>  obj-$(CONFIG_DRM_PANEL_ELIDA_KD35T133) += panel-elida-kd35t133.o
>  obj-$(CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02) += panel-feixin-k101-im2ba02.o
>  obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o
> diff --git a/drivers/gpu/drm/panel/panel-simple-edp.c b/drivers/gpu/drm/panel/panel-simple-edp.c
> new file mode 100644
> index 000000000000..5b47ee4bc338
> --- /dev/null
> +++ b/drivers/gpu/drm/panel/panel-simple-edp.c
> @@ -0,0 +1,1298 @@
> +/*
> + * Copyright (C) 2013, NVIDIA Corporation.  All rights reserved.
> + *
> + * Permission is hereby granted, free of charge, to any person obtaining a
> + * copy of this software and associated documentation files (the "Software"),
> + * to deal in the Software without restriction, including without limitation
> + * the rights to use, copy, modify, merge, publish, distribute, sub license,
> + * and/or sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following conditions:
> + *
> + * The above copyright notice and this permission notice (including the
> + * next paragraph) shall be included in all copies or substantial portions
> + * of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
> + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
> + * FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. IN NO EVENT SHALL
> + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
> + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER
> + * DEALINGS IN THE SOFTWARE.
> + */
Would be nice if you could use the SPDX thingy for the license.

> +
> +#include <linux/delay.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/iopoll.h>
> +#include <linux/module.h>
> +#include <linux/of_platform.h>
> +#include <linux/platform_device.h>
> +#include <linux/pm_runtime.h>
> +#include <linux/regulator/consumer.h>
> +
> +#include <video/display_timing.h>
> +#include <video/of_display_timing.h>
> +#include <video/videomode.h>
Sigh, we are missing a display_mode_from_timing() so these are needed.
Something for the TODO list.

> +
> +#include <drm/drm_crtc.h>
> +#include <drm/drm_device.h>
> +#include <drm/drm_dp_aux_bus.h>
> +#include <drm/drm_dp_helper.h>
> +#include <drm/drm_panel.h>
> +
> +/**
> + * struct panel_desc - Describes a simple panel.
> + */
> +struct panel_desc {
> +	/**
> +	 * @modes: Pointer to array of fixed modes appropriate for this panel.
> +	 *
> +	 * If only one mode then this can just be the address of the mode.
> +	 * NOTE: cannot be used with "timings" and also if this is specified
> +	 * then you cannot override the mode in the device tree.
> +	 */
> +	const struct drm_display_mode *modes;
> +
> +	/** @num_modes: Number of elements in modes array. */
> +	unsigned int num_modes;
> +
> +	/**
> +	 * @timings: Pointer to array of display timings
> +	 *
> +	 * NOTE: cannot be used with "modes" and also these will be used to
> +	 * validate a device tree override if one is present.
> +	 */
> +	const struct display_timing *timings;
> +
> +	/** @num_timings: Number of elements in timings array. */
> +	unsigned int num_timings;
> +
> +	/** @bpc: Bits per color. */
> +	unsigned int bpc;
> +
> +	/** @size: Structure containing the physical size of this panel. */
> +	struct {
> +		/**
> +		 * @size.width: Width (in mm) of the active display area.
> +		 */
> +		unsigned int width;
> +
> +		/**
> +		 * @size.height: Height (in mm) of the active display area.
> +		 */
> +		unsigned int height;
> +	} size;
> +
> +	/** @delay: Structure containing various delay values for this panel. */
> +	struct {
> +		/**
> +		 * @delay.prepare: Time for the panel to become ready.
> +		 *
> +		 * The time (in milliseconds) that it takes for the panel to
> +		 * become ready and start receiving video data
> +		 */
> +		unsigned int prepare;
> +
> +		/**
> +		 * @delay.hpd_absent_delay: Time to wait if HPD isn't hooked up.
> +		 *
> +		 * Add this to the prepare delay if we know Hot Plug Detect
> +		 * isn't used.
> +		 */
> +		unsigned int hpd_absent_delay;
> +
> +		/**
> +		 * @delay.prepare_to_enable: Time between prepare and enable.
> +		 *
> +		 * The minimum time, in milliseconds, that needs to have passed
> +		 * between when prepare finished and enable may begin. If at
> +		 * enable time less time has passed since prepare finished,
> +		 * the driver waits for the remaining time.
> +		 *
> +		 * If a fixed enable delay is also specified, we'll start
> +		 * counting before delaying for the fixed delay.
> +		 *
> +		 * If a fixed prepare delay is also specified, we won't start
> +		 * counting until after the fixed delay. We can't overlap this
> +		 * fixed delay with the min time because the fixed delay
> +		 * doesn't happen at the end of the function if a HPD GPIO was
> +		 * specified.
> +		 *
> +		 * In other words:
> +		 *   prepare()
> +		 *     ...
> +		 *     // do fixed prepare delay
> +		 *     // wait for HPD GPIO if applicable
> +		 *     // start counting for prepare_to_enable
> +		 *
> +		 *   enable()
> +		 *     // do fixed enable delay
> +		 *     // enforce prepare_to_enable min time
> +		 */
> +		unsigned int prepare_to_enable;
> +
> +		/**
> +		 * @delay.enable: Time for the panel to display a valid frame.
> +		 *
> +		 * The time (in milliseconds) that it takes for the panel to
> +		 * display the first valid frame after starting to receive
> +		 * video data.
> +		 */
> +		unsigned int enable;
> +
> +		/**
> +		 * @delay.disable: Time for the panel to turn the display off.
> +		 *
> +		 * The time (in milliseconds) that it takes for the panel to
> +		 * turn the display off (no content is visible).
> +		 */
> +		unsigned int disable;
> +
> +		/**
> +		 * @delay.unprepare: Time to power down completely.
> +		 *
> +		 * The time (in milliseconds) that it takes for the panel
> +		 * to power itself down completely.
> +		 *
> +		 * This time is used to prevent a future "prepare" from
> +		 * starting until at least this many milliseconds has passed.
> +		 * If at prepare time less time has passed since unprepare
> +		 * finished, the driver waits for the remaining time.
> +		 */
> +		unsigned int unprepare;
> +	} delay;
> +};
> +
> +struct panel_edp {
> +	struct drm_panel base;
> +	bool enabled;
> +	bool no_hpd;
> +
> +	bool prepared;
> +
> +	ktime_t prepared_time;
> +	ktime_t unprepared_time;
> +
> +	const struct panel_desc *desc;
> +
> +	struct regulator *supply;
> +	struct i2c_adapter *ddc;
> +	struct drm_dp_aux *aux;
> +
> +	struct gpio_desc *enable_gpio;
> +	struct gpio_desc *hpd_gpio;
> +
> +	struct edid *edid;
> +
> +	struct drm_display_mode override_mode;
> +
> +	enum drm_panel_orientation orientation;
> +};
> +
> +static inline struct panel_edp *to_panel_edp(struct drm_panel *panel)
> +{
> +	return container_of(panel, struct panel_edp, base);
> +}
> +
> +static unsigned int panel_edp_get_timings_modes(struct panel_edp *panel,
> +						struct drm_connector *connector)
> +{
> +	struct drm_display_mode *mode;
> +	unsigned int i, num = 0;
> +
> +	for (i = 0; i < panel->desc->num_timings; i++) {
> +		const struct display_timing *dt = &panel->desc->timings[i];
> +		struct videomode vm;
> +
> +		videomode_from_timing(dt, &vm);
> +		mode = drm_mode_create(connector->dev);
> +		if (!mode) {
> +			dev_err(panel->base.dev, "failed to add mode %ux%u\n",
> +				dt->hactive.typ, dt->vactive.typ);
> +			continue;
> +		}
> +
> +		drm_display_mode_from_videomode(&vm, mode);
> +
> +		mode->type |= DRM_MODE_TYPE_DRIVER;
> +
> +		if (panel->desc->num_timings == 1)
> +			mode->type |= DRM_MODE_TYPE_PREFERRED;
> +
> +		drm_mode_probed_add(connector, mode);
> +		num++;
> +	}
> +
> +	return num;
> +}
> +
> +static unsigned int panel_edp_get_display_modes(struct panel_edp *panel,
> +						struct drm_connector *connector)
> +{
> +	struct drm_display_mode *mode;
> +	unsigned int i, num = 0;
> +
> +	for (i = 0; i < panel->desc->num_modes; i++) {
> +		const struct drm_display_mode *m = &panel->desc->modes[i];
> +
> +		mode = drm_mode_duplicate(connector->dev, m);
> +		if (!mode) {
> +			dev_err(panel->base.dev, "failed to add mode %ux%u@%u\n",
> +				m->hdisplay, m->vdisplay,
> +				drm_mode_vrefresh(m));
> +			continue;
> +		}
> +
> +		mode->type |= DRM_MODE_TYPE_DRIVER;
> +
> +		if (panel->desc->num_modes == 1)
> +			mode->type |= DRM_MODE_TYPE_PREFERRED;
> +
> +		drm_mode_set_name(mode);
> +
> +		drm_mode_probed_add(connector, mode);
> +		num++;
> +	}
> +
> +	return num;
> +}
> +
> +static int panel_edp_get_non_edid_modes(struct panel_edp *panel,
> +					struct drm_connector *connector)
> +{
> +	struct drm_display_mode *mode;
> +	bool has_override = panel->override_mode.type;
> +	unsigned int num = 0;
> +
> +	if (!panel->desc)
> +		return 0;
> +
> +	if (has_override) {
> +		mode = drm_mode_duplicate(connector->dev,
> +					  &panel->override_mode);
> +		if (mode) {
> +			drm_mode_probed_add(connector, mode);
> +			num = 1;
> +		} else {
> +			dev_err(panel->base.dev, "failed to add override mode\n");
> +		}
> +	}
> +
> +	/* Only add timings if override was not there or failed to validate */
> +	if (num == 0 && panel->desc->num_timings)
> +		num = panel_edp_get_timings_modes(panel, connector);
> +
> +	/*
> +	 * Only add fixed modes if timings/override added no mode.
> +	 *
> +	 * We should only ever have either the display timings specified
> +	 * or a fixed mode. Anything else is rather bogus.
> +	 */
> +	WARN_ON(panel->desc->num_timings && panel->desc->num_modes);
> +	if (num == 0)
> +		num = panel_edp_get_display_modes(panel, connector);
> +
> +	connector->display_info.bpc = panel->desc->bpc;
> +	connector->display_info.width_mm = panel->desc->size.width;
> +	connector->display_info.height_mm = panel->desc->size.height;
> +
> +	return num;
> +}
> +
> +static void panel_edp_wait(ktime_t start_ktime, unsigned int min_ms)
> +{
> +	ktime_t now_ktime, min_ktime;
> +
> +	if (!min_ms)
> +		return;
> +
> +	min_ktime = ktime_add(start_ktime, ms_to_ktime(min_ms));
> +	now_ktime = ktime_get();
> +
> +	if (ktime_before(now_ktime, min_ktime))
> +		msleep(ktime_to_ms(ktime_sub(min_ktime, now_ktime)) + 1);
> +}
> +
> +static int panel_edp_disable(struct drm_panel *panel)
> +{
> +	struct panel_edp *p = to_panel_edp(panel);
> +
> +	if (!p->enabled)
> +		return 0;
> +
> +	if (p->desc->delay.disable)
> +		msleep(p->desc->delay.disable);
> +
> +	p->enabled = false;
> +
> +	return 0;
> +}
> +
> +static int panel_edp_suspend(struct device *dev)
> +{
> +	struct panel_edp *p = dev_get_drvdata(dev);
> +
> +	gpiod_set_value_cansleep(p->enable_gpio, 0);
> +	regulator_disable(p->supply);
> +	p->unprepared_time = ktime_get();
> +
> +	kfree(p->edid);
> +	p->edid = NULL;
> +
> +	return 0;
> +}
> +
> +static int panel_edp_unprepare(struct drm_panel *panel)
> +{
> +	struct panel_edp *p = to_panel_edp(panel);
> +	int ret;
> +
> +	/* Unpreparing when already unprepared is a no-op */
> +	if (!p->prepared)
> +		return 0;
> +
> +	pm_runtime_mark_last_busy(panel->dev);
> +	ret = pm_runtime_put_autosuspend(panel->dev);
> +	if (ret < 0)
> +		return ret;
> +	p->prepared = false;
> +
> +	return 0;
> +}
> +
> +static int panel_edp_get_hpd_gpio(struct device *dev, struct panel_edp *p)
> +{
> +	int err;
> +
> +	p->hpd_gpio = devm_gpiod_get_optional(dev, "hpd", GPIOD_IN);
> +	if (IS_ERR(p->hpd_gpio)) {
> +		err = PTR_ERR(p->hpd_gpio);
> +
> +		if (err != -EPROBE_DEFER)
> +			dev_err(dev, "failed to get 'hpd' GPIO: %d\n", err);
> +
> +		return err;
> +	}
> +
> +	return 0;
> +}
> +
> +static int panel_edp_prepare_once(struct panel_edp *p)
> +{
> +	struct device *dev = p->base.dev;
> +	unsigned int delay;
> +	int err;
> +	int hpd_asserted;
> +	unsigned long hpd_wait_us;
> +
> +	panel_edp_wait(p->unprepared_time, p->desc->delay.unprepare);
> +
> +	err = regulator_enable(p->supply);
> +	if (err < 0) {
> +		dev_err(dev, "failed to enable supply: %d\n", err);
> +		return err;
> +	}
> +
> +	gpiod_set_value_cansleep(p->enable_gpio, 1);
> +
> +	delay = p->desc->delay.prepare;
> +	if (p->no_hpd)
> +		delay += p->desc->delay.hpd_absent_delay;
> +	if (delay)
> +		msleep(delay);
> +
> +	if (p->hpd_gpio) {
> +		if (p->desc->delay.hpd_absent_delay)
> +			hpd_wait_us = p->desc->delay.hpd_absent_delay * 1000UL;
> +		else
> +			hpd_wait_us = 2000000;
> +
> +		err = readx_poll_timeout(gpiod_get_value_cansleep, p->hpd_gpio,
> +					 hpd_asserted, hpd_asserted,
> +					 1000, hpd_wait_us);
> +		if (hpd_asserted < 0)
> +			err = hpd_asserted;
> +
> +		if (err) {
> +			if (err != -ETIMEDOUT)
> +				dev_err(dev,
> +					"error waiting for hpd GPIO: %d\n", err);
> +			goto error;
> +		}
> +	}
> +
> +	p->prepared_time = ktime_get();
> +
> +	return 0;
> +
> +error:
> +	gpiod_set_value_cansleep(p->enable_gpio, 0);
> +	regulator_disable(p->supply);
> +	p->unprepared_time = ktime_get();
> +
> +	return err;
> +}
> +
> +/*
> + * Some panels simply don't always come up and need to be power cycled to
> + * work properly.  We'll allow for a handful of retries.
> + */
> +#define MAX_PANEL_PREPARE_TRIES		5
> +
> +static int panel_edp_resume(struct device *dev)
> +{
> +	struct panel_edp *p = dev_get_drvdata(dev);
> +	int ret;
> +	int try;
> +
> +	for (try = 0; try < MAX_PANEL_PREPARE_TRIES; try++) {
> +		ret = panel_edp_prepare_once(p);
> +		if (ret != -ETIMEDOUT)
> +			break;
> +	}
> +
> +	if (ret == -ETIMEDOUT)
> +		dev_err(dev, "Prepare timeout after %d tries\n", try);
> +	else if (try)
> +		dev_warn(dev, "Prepare needed %d retries\n", try);
> +
> +	return ret;
> +}
> +
> +static int panel_edp_prepare(struct drm_panel *panel)
> +{
> +	struct panel_edp *p = to_panel_edp(panel);
> +	int ret;
> +
> +	/* Preparing when already prepared is a no-op */
> +	if (p->prepared)
> +		return 0;
> +
> +	ret = pm_runtime_get_sync(panel->dev);
> +	if (ret < 0) {
> +		pm_runtime_put_autosuspend(panel->dev);
> +		return ret;
> +	}
> +
> +	p->prepared = true;
> +
> +	return 0;
> +}
> +
> +static int panel_edp_enable(struct drm_panel *panel)
> +{
> +	struct panel_edp *p = to_panel_edp(panel);
> +
> +	if (p->enabled)
> +		return 0;
> +
> +	if (p->desc->delay.enable)
> +		msleep(p->desc->delay.enable);
> +
> +	panel_edp_wait(p->prepared_time, p->desc->delay.prepare_to_enable);
> +
> +	p->enabled = true;
> +
> +	return 0;
> +}
> +
> +static int panel_edp_get_modes(struct drm_panel *panel,
> +				  struct drm_connector *connector)
> +{
> +	struct panel_edp *p = to_panel_edp(panel);
> +	int num = 0;
> +
> +	/* probe EDID if a DDC bus is available */
> +	if (p->ddc) {
> +		pm_runtime_get_sync(panel->dev);
> +
> +		if (!p->edid)
> +			p->edid = drm_get_edid(connector, p->ddc);
> +
> +		if (p->edid)
> +			num += drm_add_edid_modes(connector, p->edid);
> +
> +		pm_runtime_mark_last_busy(panel->dev);
> +		pm_runtime_put_autosuspend(panel->dev);
> +	}
> +
> +	/* add hard-coded panel modes */
> +	num += panel_edp_get_non_edid_modes(p, connector);
> +
> +	/* set up connector's "panel orientation" property */
> +	drm_connector_set_panel_orientation(connector, p->orientation);
> +
> +	return num;
> +}
> +
> +static int panel_edp_get_timings(struct drm_panel *panel,
> +				    unsigned int num_timings,
> +				    struct display_timing *timings)
> +{
> +	struct panel_edp *p = to_panel_edp(panel);
> +	unsigned int i;
> +
> +	if (p->desc->num_timings < num_timings)
> +		num_timings = p->desc->num_timings;
> +
> +	if (timings)
> +		for (i = 0; i < num_timings; i++)
> +			timings[i] = p->desc->timings[i];
> +
> +	return p->desc->num_timings;
> +}
> +
> +static const struct drm_panel_funcs panel_edp_funcs = {
> +	.disable = panel_edp_disable,
> +	.unprepare = panel_edp_unprepare,
> +	.prepare = panel_edp_prepare,
> +	.enable = panel_edp_enable,
> +	.get_modes = panel_edp_get_modes,
> +	.get_timings = panel_edp_get_timings,
> +};
> +
> +#define PANEL_EDP_BOUNDS_CHECK(to_check, bounds, field) \
> +	(to_check->field.typ >= bounds->field.min && \
> +	 to_check->field.typ <= bounds->field.max)
> +static void panel_edp_parse_panel_timing_node(struct device *dev,
> +					      struct panel_edp *panel,
> +					      const struct display_timing *ot)
> +{
> +	const struct panel_desc *desc = panel->desc;
> +	struct videomode vm;
> +	unsigned int i;
> +
> +	if (WARN_ON(desc->num_modes)) {
> +		dev_err(dev, "Reject override mode: panel has a fixed mode\n");
> +		return;
> +	}
> +	if (WARN_ON(!desc->num_timings)) {
> +		dev_err(dev, "Reject override mode: no timings specified\n");
> +		return;
> +	}
> +
> +	for (i = 0; i < panel->desc->num_timings; i++) {
> +		const struct display_timing *dt = &panel->desc->timings[i];
> +
> +		if (!PANEL_EDP_BOUNDS_CHECK(ot, dt, hactive) ||
> +		    !PANEL_EDP_BOUNDS_CHECK(ot, dt, hfront_porch) ||
> +		    !PANEL_EDP_BOUNDS_CHECK(ot, dt, hback_porch) ||
> +		    !PANEL_EDP_BOUNDS_CHECK(ot, dt, hsync_len) ||
> +		    !PANEL_EDP_BOUNDS_CHECK(ot, dt, vactive) ||
> +		    !PANEL_EDP_BOUNDS_CHECK(ot, dt, vfront_porch) ||
> +		    !PANEL_EDP_BOUNDS_CHECK(ot, dt, vback_porch) ||
> +		    !PANEL_EDP_BOUNDS_CHECK(ot, dt, vsync_len))
> +			continue;
> +
> +		if (ot->flags != dt->flags)
> +			continue;
> +
> +		videomode_from_timing(ot, &vm);
> +		drm_display_mode_from_videomode(&vm, &panel->override_mode);
> +		panel->override_mode.type |= DRM_MODE_TYPE_DRIVER |
> +					     DRM_MODE_TYPE_PREFERRED;
> +		break;
> +	}
> +
> +	if (WARN_ON(!panel->override_mode.type))
> +		dev_err(dev, "Reject override mode: No display_timing found\n");
> +}
> +
> +static int panel_edp_probe(struct device *dev, const struct panel_desc *desc,
> +			      struct drm_dp_aux *aux)
> +{
> +	struct panel_edp *panel;
> +	struct display_timing dt;
> +	struct device_node *ddc;
> +	int err;
> +
> +	panel = devm_kzalloc(dev, sizeof(*panel), GFP_KERNEL);
> +	if (!panel)
> +		return -ENOMEM;
> +
> +	panel->enabled = false;
> +	panel->prepared_time = 0;
> +	panel->desc = desc;
> +	panel->aux = aux;
> +
> +	panel->no_hpd = of_property_read_bool(dev->of_node, "no-hpd");
> +	if (!panel->no_hpd) {
> +		err = panel_edp_get_hpd_gpio(dev, panel);
> +		if (err)
> +			return err;
> +	}
> +
> +	panel->supply = devm_regulator_get(dev, "power");
> +	if (IS_ERR(panel->supply))
> +		return PTR_ERR(panel->supply);
> +
> +	panel->enable_gpio = devm_gpiod_get_optional(dev, "enable",
> +						     GPIOD_OUT_LOW);
> +	if (IS_ERR(panel->enable_gpio)) {
> +		err = PTR_ERR(panel->enable_gpio);
> +		if (err != -EPROBE_DEFER)
> +			dev_err(dev, "failed to request GPIO: %d\n", err);
> +		return err;
> +	}
> +
> +	err = of_drm_get_panel_orientation(dev->of_node, &panel->orientation);
> +	if (err) {
> +		dev_err(dev, "%pOF: failed to get orientation %d\n", dev->of_node, err);
> +		return err;
> +	}
> +
> +	ddc = of_parse_phandle(dev->of_node, "ddc-i2c-bus", 0);
> +	if (ddc) {
> +		panel->ddc = of_find_i2c_adapter_by_node(ddc);
> +		of_node_put(ddc);
> +
> +		if (!panel->ddc)
> +			return -EPROBE_DEFER;
> +	} else if (aux) {
> +		panel->ddc = &aux->ddc;
> +	}
> +
> +	if (!of_get_display_timing(dev->of_node, "panel-timing", &dt))
> +		panel_edp_parse_panel_timing_node(dev, panel, &dt);
> +
> +	/* Catch common mistakes for panels. */
> +	if (desc->bpc != 6 && desc->bpc != 8 && desc->bpc != 10)
> +		dev_warn(dev, "Expected bpc in {6,8,10} but got: %u\n", desc->bpc);
> +
> +	dev_set_drvdata(dev, panel);
> +
> +	/*
> +	 * We use runtime PM for prepare / unprepare since those power the panel
> +	 * on and off and those can be very slow operations. This is important
> +	 * to optimize powering the panel on briefly to read the EDID before
> +	 * fully enabling the panel.
> +	 */
> +	pm_runtime_enable(dev);
> +	pm_runtime_set_autosuspend_delay(dev, 1000);
> +	pm_runtime_use_autosuspend(dev);
> +
> +	drm_panel_init(&panel->base, dev, &panel_edp_funcs, DRM_MODE_CONNECTOR_eDP);
> +
> +	err = drm_panel_of_backlight(&panel->base);
> +	if (err)
> +		goto disable_pm_runtime;
> +
> +	if (!panel->base.backlight && panel->aux) {
> +		pm_runtime_get_sync(dev);
> +		err = drm_panel_dp_aux_backlight(&panel->base, panel->aux);
> +		pm_runtime_mark_last_busy(dev);
> +		pm_runtime_put_autosuspend(dev);
> +		if (err)
> +			goto disable_pm_runtime;
> +	}
> +
> +	drm_panel_add(&panel->base);
> +
> +	return 0;
> +
> +disable_pm_runtime:
> +	pm_runtime_dont_use_autosuspend(dev);
> +	pm_runtime_disable(dev);
> +	if (panel->ddc && (!panel->aux || panel->ddc != &panel->aux->ddc))
> +		put_device(&panel->ddc->dev);
> +
> +	return err;
> +}
> +
> +static int panel_edp_remove(struct device *dev)
> +{
> +	struct panel_edp *panel = dev_get_drvdata(dev);
> +
> +	drm_panel_remove(&panel->base);
> +	drm_panel_disable(&panel->base);
> +	drm_panel_unprepare(&panel->base);
> +
> +	pm_runtime_dont_use_autosuspend(dev);
> +	pm_runtime_disable(dev);
> +	if (panel->ddc && (!panel->aux || panel->ddc != &panel->aux->ddc))
> +		put_device(&panel->ddc->dev);
> +
> +	return 0;
> +}
> +
> +static void panel_edp_shutdown(struct device *dev)
> +{
> +	struct panel_edp *panel = dev_get_drvdata(dev);
> +
> +	drm_panel_disable(&panel->base);
> +	drm_panel_unprepare(&panel->base);
> +}
> +
> +static const struct drm_display_mode auo_b116xak01_mode = {
> +	.clock = 69300,
> +	.hdisplay = 1366,
> +	.hsync_start = 1366 + 48,
> +	.hsync_end = 1366 + 48 + 32,
> +	.htotal = 1366 + 48 + 32 + 10,
> +	.vdisplay = 768,
> +	.vsync_start = 768 + 4,
> +	.vsync_end = 768 + 4 + 6,
> +	.vtotal = 768 + 4 + 6 + 15,
> +	.flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
> +};
> +
> +static const struct panel_desc auo_b116xak01 = {
> +	.modes = &auo_b116xak01_mode,
> +	.num_modes = 1,
> +	.bpc = 6,
> +	.size = {
> +		.width = 256,
> +		.height = 144,
> +	},
> +	.delay = {
> +		.hpd_absent_delay = 200,
> +	},
> +};
> +
> +static const struct drm_display_mode auo_b116xw03_mode = {
> +	.clock = 70589,
> +	.hdisplay = 1366,
> +	.hsync_start = 1366 + 40,
> +	.hsync_end = 1366 + 40 + 40,
> +	.htotal = 1366 + 40 + 40 + 32,
> +	.vdisplay = 768,
> +	.vsync_start = 768 + 10,
> +	.vsync_end = 768 + 10 + 12,
> +	.vtotal = 768 + 10 + 12 + 6,
> +	.flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
> +};
> +
> +static const struct panel_desc auo_b116xw03 = {
> +	.modes = &auo_b116xw03_mode,
> +	.num_modes = 1,
> +	.bpc = 6,
> +	.size = {
> +		.width = 256,
> +		.height = 144,
> +	},
> +	.delay = {
> +		.enable = 400,
> +	},
> +};
> +
> +static const struct drm_display_mode auo_b133han05_mode = {
> +	.clock = 142600,
> +	.hdisplay = 1920,
> +	.hsync_start = 1920 + 58,
> +	.hsync_end = 1920 + 58 + 42,
> +	.htotal = 1920 + 58 + 42 + 60,
> +	.vdisplay = 1080,
> +	.vsync_start = 1080 + 3,
> +	.vsync_end = 1080 + 3 + 5,
> +	.vtotal = 1080 + 3 + 5 + 54,
> +};
> +
> +static const struct panel_desc auo_b133han05 = {
> +	.modes = &auo_b133han05_mode,
> +	.num_modes = 1,
> +	.bpc = 8,
> +	.size = {
> +		.width = 293,
> +		.height = 165,
> +	},
> +	.delay = {
> +		.prepare = 100,
> +		.enable = 20,
> +		.unprepare = 50,
> +	},
> +};
> +
> +static const struct drm_display_mode auo_b140han06_mode = {
> +	.clock = 141000,
> +	.hdisplay = 1920,
> +	.hsync_start = 1920 + 16,
> +	.hsync_end = 1920 + 16 + 16,
> +	.htotal = 1920 + 16 + 16 + 152,
> +	.vdisplay = 1080,
> +	.vsync_start = 1080 + 3,
> +	.vsync_end = 1080 + 3 + 14,
> +	.vtotal = 1080 + 3 + 14 + 19,
> +};
> +
> +static const struct panel_desc auo_b140han06 = {
> +	.modes = &auo_b140han06_mode,
> +	.num_modes = 1,
> +	.bpc = 8,
> +	.size = {
> +		.width = 309,
> +		.height = 174,
> +	},
> +	.delay = {
> +		.prepare = 100,
> +		.enable = 20,
> +		.unprepare = 50,
> +	},
> +};
> +
> +static const struct drm_display_mode boe_nv110wtm_n61_modes[] = {
> +	{
> +		.clock = 207800,
> +		.hdisplay = 2160,
> +		.hsync_start = 2160 + 48,
> +		.hsync_end = 2160 + 48 + 32,
> +		.htotal = 2160 + 48 + 32 + 100,
> +		.vdisplay = 1440,
> +		.vsync_start = 1440 + 3,
> +		.vsync_end = 1440 + 3 + 6,
> +		.vtotal = 1440 + 3 + 6 + 31,
> +		.flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_NVSYNC,
> +	},
> +	{
> +		.clock = 138500,
> +		.hdisplay = 2160,
> +		.hsync_start = 2160 + 48,
> +		.hsync_end = 2160 + 48 + 32,
> +		.htotal = 2160 + 48 + 32 + 100,
> +		.vdisplay = 1440,
> +		.vsync_start = 1440 + 3,
> +		.vsync_end = 1440 + 3 + 6,
> +		.vtotal = 1440 + 3 + 6 + 31,
> +		.flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_NVSYNC,
> +	},
> +};
> +
> +static const struct panel_desc boe_nv110wtm_n61 = {
> +	.modes = boe_nv110wtm_n61_modes,
> +	.num_modes = ARRAY_SIZE(boe_nv110wtm_n61_modes),
> +	.bpc = 8,
> +	.size = {
> +		.width = 233,
> +		.height = 155,
> +	},
> +	.delay = {
> +		.hpd_absent_delay = 200,
> +		.prepare_to_enable = 80,
> +		.enable = 50,
> +		.unprepare = 500,
> +	},
> +};
> +
> +/* Also used for boe_nv133fhm_n62 */
> +static const struct drm_display_mode boe_nv133fhm_n61_modes = {
> +	.clock = 147840,
> +	.hdisplay = 1920,
> +	.hsync_start = 1920 + 48,
> +	.hsync_end = 1920 + 48 + 32,
> +	.htotal = 1920 + 48 + 32 + 200,
> +	.vdisplay = 1080,
> +	.vsync_start = 1080 + 3,
> +	.vsync_end = 1080 + 3 + 6,
> +	.vtotal = 1080 + 3 + 6 + 31,
> +	.flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_NVSYNC,
> +};
> +
> +/* Also used for boe_nv133fhm_n62 */
> +static const struct panel_desc boe_nv133fhm_n61 = {
> +	.modes = &boe_nv133fhm_n61_modes,
> +	.num_modes = 1,
> +	.bpc = 6,
> +	.size = {
> +		.width = 294,
> +		.height = 165,
> +	},
> +	.delay = {
> +		/*
> +		 * When power is first given to the panel there's a short
> +		 * spike on the HPD line.  It was explained that this spike
> +		 * was until the TCON data download was complete.  On
> +		 * one system this was measured at 8 ms.  We'll put 15 ms
> +		 * in the prepare delay just to be safe and take it away
> +		 * from the hpd_absent_delay (which would otherwise be 200 ms)
> +		 * to handle this.  That means:
> +		 * - If HPD isn't hooked up you still have 200 ms delay.
> +		 * - If HPD is hooked up we won't try to look at it for the
> +		 *   first 15 ms.
> +		 */
> +		.prepare = 15,
> +		.hpd_absent_delay = 185,
> +
> +		.unprepare = 500,
> +	},
> +};
> +
> +static const struct drm_display_mode boe_nv140fhmn49_modes[] = {
> +	{
> +		.clock = 148500,
> +		.hdisplay = 1920,
> +		.hsync_start = 1920 + 48,
> +		.hsync_end = 1920 + 48 + 32,
> +		.htotal = 2200,
> +		.vdisplay = 1080,
> +		.vsync_start = 1080 + 3,
> +		.vsync_end = 1080 + 3 + 5,
> +		.vtotal = 1125,
> +	},
> +};
> +
> +static const struct panel_desc boe_nv140fhmn49 = {
> +	.modes = boe_nv140fhmn49_modes,
> +	.num_modes = ARRAY_SIZE(boe_nv140fhmn49_modes),
> +	.bpc = 6,
> +	.size = {
> +		.width = 309,
> +		.height = 174,
> +	},
> +	.delay = {
> +		.prepare = 210,
> +		.enable = 50,
> +		.unprepare = 160,
> +	},
> +};
> +
> +static const struct drm_display_mode innolux_n116bca_ea1_mode = {
> +	.clock = 76420,
> +	.hdisplay = 1366,
> +	.hsync_start = 1366 + 136,
> +	.hsync_end = 1366 + 136 + 30,
> +	.htotal = 1366 + 136 + 30 + 60,
> +	.vdisplay = 768,
> +	.vsync_start = 768 + 8,
> +	.vsync_end = 768 + 8 + 12,
> +	.vtotal = 768 + 8 + 12 + 12,
> +	.flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
> +};
> +
> +static const struct panel_desc innolux_n116bca_ea1 = {
> +	.modes = &innolux_n116bca_ea1_mode,
> +	.num_modes = 1,
> +	.bpc = 6,
> +	.size = {
> +		.width = 256,
> +		.height = 144,
> +	},
> +	.delay = {
> +		.hpd_absent_delay = 200,
> +		.prepare_to_enable = 80,
> +		.unprepare = 500,
> +	},
> +};
> +
> +/*
> + * Datasheet specifies that at 60 Hz refresh rate:
> + * - total horizontal time: { 1506, 1592, 1716 }
> + * - total vertical time: { 788, 800, 868 }
> + *
> + * ...but doesn't go into exactly how that should be split into a front
> + * porch, back porch, or sync length.  For now we'll leave a single setting
> + * here which allows a bit of tweaking of the pixel clock at the expense of
> + * refresh rate.
> + */
> +static const struct display_timing innolux_n116bge_timing = {
> +	.pixelclock = { 72600000, 76420000, 80240000 },
> +	.hactive = { 1366, 1366, 1366 },
> +	.hfront_porch = { 136, 136, 136 },
> +	.hback_porch = { 60, 60, 60 },
> +	.hsync_len = { 30, 30, 30 },
> +	.vactive = { 768, 768, 768 },
> +	.vfront_porch = { 8, 8, 8 },
> +	.vback_porch = { 12, 12, 12 },
> +	.vsync_len = { 12, 12, 12 },
> +	.flags = DISPLAY_FLAGS_VSYNC_LOW | DISPLAY_FLAGS_HSYNC_LOW,
> +};
> +
> +static const struct panel_desc innolux_n116bge = {
> +	.timings = &innolux_n116bge_timing,
> +	.num_timings = 1,
> +	.bpc = 6,
> +	.size = {
> +		.width = 256,
> +		.height = 144,
> +	},
> +};
> +
> +static const struct drm_display_mode innolux_n125hce_gn1_mode = {
> +	.clock = 162000,
> +	.hdisplay = 1920,
> +	.hsync_start = 1920 + 40,
> +	.hsync_end = 1920 + 40 + 40,
> +	.htotal = 1920 + 40 + 40 + 80,
> +	.vdisplay = 1080,
> +	.vsync_start = 1080 + 4,
> +	.vsync_end = 1080 + 4 + 4,
> +	.vtotal = 1080 + 4 + 4 + 24,
> +};
> +
> +static const struct panel_desc innolux_n125hce_gn1 = {
> +	.modes = &innolux_n125hce_gn1_mode,
> +	.num_modes = 1,
> +	.bpc = 8,
> +	.size = {
> +		.width = 276,
> +		.height = 155,
> +	},
> +};
> +
> +static const struct drm_display_mode ivo_m133nwf4_r0_mode = {
> +	.clock = 138778,
> +	.hdisplay = 1920,
> +	.hsync_start = 1920 + 24,
> +	.hsync_end = 1920 + 24 + 48,
> +	.htotal = 1920 + 24 + 48 + 88,
> +	.vdisplay = 1080,
> +	.vsync_start = 1080 + 3,
> +	.vsync_end = 1080 + 3 + 12,
> +	.vtotal = 1080 + 3 + 12 + 17,
> +	.flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC,
> +};
> +
> +static const struct panel_desc ivo_m133nwf4_r0 = {
> +	.modes = &ivo_m133nwf4_r0_mode,
> +	.num_modes = 1,
> +	.bpc = 8,
> +	.size = {
> +		.width = 294,
> +		.height = 165,
> +	},
> +	.delay = {
> +		.hpd_absent_delay = 200,
> +		.unprepare = 500,
> +	},
> +};
> +
> +static const struct drm_display_mode kingdisplay_kd116n21_30nv_a010_mode = {
> +	.clock = 81000,
> +	.hdisplay = 1366,
> +	.hsync_start = 1366 + 40,
> +	.hsync_end = 1366 + 40 + 32,
> +	.htotal = 1366 + 40 + 32 + 62,
> +	.vdisplay = 768,
> +	.vsync_start = 768 + 5,
> +	.vsync_end = 768 + 5 + 5,
> +	.vtotal = 768 + 5 + 5 + 122,
> +	.flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
> +};
> +
> +static const struct panel_desc kingdisplay_kd116n21_30nv_a010 = {
> +	.modes = &kingdisplay_kd116n21_30nv_a010_mode,
> +	.num_modes = 1,
> +	.bpc = 6,
> +	.size = {
> +		.width = 256,
> +		.height = 144,
> +	},
> +	.delay = {
> +		.hpd_absent_delay = 200,
> +	},
> +};
> +
> +static const struct drm_display_mode lg_lp120up1_mode = {
> +	.clock = 162300,
> +	.hdisplay = 1920,
> +	.hsync_start = 1920 + 40,
> +	.hsync_end = 1920 + 40 + 40,
> +	.htotal = 1920 + 40 + 40 + 80,
> +	.vdisplay = 1280,
> +	.vsync_start = 1280 + 4,
> +	.vsync_end = 1280 + 4 + 4,
> +	.vtotal = 1280 + 4 + 4 + 12,
> +};
> +
> +static const struct panel_desc lg_lp120up1 = {
> +	.modes = &lg_lp120up1_mode,
> +	.num_modes = 1,
> +	.bpc = 8,
> +	.size = {
> +		.width = 267,
> +		.height = 183,
> +	},
> +};
> +
> +static const struct drm_display_mode neweast_wjfh116008a_modes[] = {
> +	{
> +		.clock = 138500,
> +		.hdisplay = 1920,
> +		.hsync_start = 1920 + 48,
> +		.hsync_end = 1920 + 48 + 32,
> +		.htotal = 1920 + 48 + 32 + 80,
> +		.vdisplay = 1080,
> +		.vsync_start = 1080 + 3,
> +		.vsync_end = 1080 + 3 + 5,
> +		.vtotal = 1080 + 3 + 5 + 23,
> +		.flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
> +	}, {
> +		.clock = 110920,
> +		.hdisplay = 1920,
> +		.hsync_start = 1920 + 48,
> +		.hsync_end = 1920 + 48 + 32,
> +		.htotal = 1920 + 48 + 32 + 80,
> +		.vdisplay = 1080,
> +		.vsync_start = 1080 + 3,
> +		.vsync_end = 1080 + 3 + 5,
> +		.vtotal = 1080 + 3 + 5 + 23,
> +		.flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
> +	}
> +};
> +
> +static const struct panel_desc neweast_wjfh116008a = {
> +	.modes = neweast_wjfh116008a_modes,
> +	.num_modes = 2,
> +	.bpc = 6,
> +	.size = {
> +		.width = 260,
> +		.height = 150,
> +	},
> +	.delay = {
> +		.prepare = 110,
> +		.enable = 20,
> +		.unprepare = 500,
> +	},
> +};
> +
> +static const struct of_device_id platform_of_match[] = {
> +	{
> +		.compatible = "auo,b116xa01",
> +		.data = &auo_b116xak01,
> +	}, {
> +		.compatible = "auo,b116xw03",
> +		.data = &auo_b116xw03,
> +	}, {
> +		.compatible = "auo,b133han05",
> +		.data = &auo_b133han05,
> +	}, {
> +		.compatible = "auo,b140han06",
> +		.data = &auo_b140han06,
> +	}, {
> +		.compatible = "boe,nv110wtm-n61",
> +		.data = &boe_nv110wtm_n61,
> +	}, {
> +		.compatible = "boe,nv133fhm-n61",
> +		.data = &boe_nv133fhm_n61,
> +	}, {
> +		.compatible = "boe,nv133fhm-n62",
> +		.data = &boe_nv133fhm_n61,
> +	}, {
> +		.compatible = "boe,nv140fhmn49",
> +		.data = &boe_nv140fhmn49,
> +	}, {
> +		.compatible = "innolux,n116bca-ea1",
> +		.data = &innolux_n116bca_ea1,
> +	}, {
> +		.compatible = "innolux,n116bge",
> +		.data = &innolux_n116bge,
> +	}, {
> +		.compatible = "innolux,n125hce-gn1",
> +		.data = &innolux_n125hce_gn1,
> +	}, {
> +		.compatible = "ivo,m133nwf4-r0",
> +		.data = &ivo_m133nwf4_r0,
> +	}, {
> +		.compatible = "kingdisplay,kd116n21-30nv-a010",
> +		.data = &kingdisplay_kd116n21_30nv_a010,
> +	}, {
> +		.compatible = "lg,lp120up1",
> +		.data = &lg_lp120up1,
> +	}, {
> +		.compatible = "neweast,wjfh116008a",
> +		.data = &neweast_wjfh116008a,
> +	}, {
> +		/* sentinel */
> +	}
> +};
> +MODULE_DEVICE_TABLE(of, platform_of_match);
> +
> +static int panel_edp_platform_probe(struct platform_device *pdev)
> +{
> +	const struct of_device_id *id;
> +
> +	id = of_match_node(platform_of_match, pdev->dev.of_node);
> +	if (!id)
> +		return -ENODEV;
> +
> +	return panel_edp_probe(&pdev->dev, id->data, NULL);
> +}
> +
> +static int panel_edp_platform_remove(struct platform_device *pdev)
> +{
> +	return panel_edp_remove(&pdev->dev);
> +}
> +
> +static void panel_edp_platform_shutdown(struct platform_device *pdev)
> +{
> +	panel_edp_shutdown(&pdev->dev);
> +}
> +
> +static const struct dev_pm_ops panel_edp_pm_ops = {
> +	SET_RUNTIME_PM_OPS(panel_edp_suspend, panel_edp_resume, NULL)
> +	SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
> +				pm_runtime_force_resume)
> +};
> +
> +static struct platform_driver panel_edp_platform_driver = {
> +	.driver = {
> +		.name = "panel-simple-edp",
> +		.of_match_table = platform_of_match,
> +		.pm = &panel_edp_pm_ops,
> +	},
> +	.probe = panel_edp_platform_probe,
> +	.remove = panel_edp_platform_remove,
> +	.shutdown = panel_edp_platform_shutdown,
> +};
> +
> +static int panel_edp_dp_aux_ep_probe(struct dp_aux_ep_device *aux_ep)
> +{
> +	const struct of_device_id *id;
> +
> +	id = of_match_node(platform_of_match, aux_ep->dev.of_node);
> +	if (!id)
> +		return -ENODEV;
> +
> +	return panel_edp_probe(&aux_ep->dev, id->data, aux_ep->aux);
> +}
> +
> +static void panel_edp_dp_aux_ep_remove(struct dp_aux_ep_device *aux_ep)
> +{
> +	panel_edp_remove(&aux_ep->dev);
> +}
> +
> +static void panel_edp_dp_aux_ep_shutdown(struct dp_aux_ep_device *aux_ep)
> +{
> +	panel_edp_shutdown(&aux_ep->dev);
> +}
> +
> +static struct dp_aux_ep_driver panel_edp_dp_aux_ep_driver = {
> +	.driver = {
> +		.name = "panel-simple-dp-aux",
> +		.of_match_table = platform_of_match,	/* Same as platform one! */
> +		.pm = &panel_edp_pm_ops,
> +	},
> +	.probe = panel_edp_dp_aux_ep_probe,
> +	.remove = panel_edp_dp_aux_ep_remove,
> +	.shutdown = panel_edp_dp_aux_ep_shutdown,
> +};
> +
> +static int __init panel_edp_init(void)
> +{
> +	int err;
> +
> +	err = platform_driver_register(&panel_edp_platform_driver);
> +	if (err < 0)
> +		return err;
> +
> +	err = dp_aux_dp_driver_register(&panel_edp_dp_aux_ep_driver);
> +	if (err < 0)
> +		goto err_did_platform_register;
> +
> +	return 0;
> +
> +err_did_platform_register:
> +	platform_driver_unregister(&panel_edp_platform_driver);
> +
> +	return err;
> +}
> +module_init(panel_edp_init);
> +
> +static void __exit panel_edp_exit(void)
> +{
> +	dp_aux_dp_driver_unregister(&panel_edp_dp_aux_ep_driver);
> +	platform_driver_unregister(&panel_edp_platform_driver);
> +}
> +module_exit(panel_edp_exit);
> +
> +MODULE_AUTHOR("Thierry Reding <treding@xxxxxxxxxx>");
> +MODULE_DESCRIPTION("DRM Driver for Simple eDP Panels");
> +MODULE_LICENSE("GPL and additional rights");
> diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
> index 4ec310a650cd..29b2c98231fc 100644
> --- a/drivers/gpu/drm/panel/panel-simple.c
> +++ b/drivers/gpu/drm/panel/panel-simple.c
> @@ -36,8 +36,6 @@
>  
>  #include <drm/drm_crtc.h>
>  #include <drm/drm_device.h>
> -#include <drm/drm_dp_aux_bus.h>
> -#include <drm/drm_dp_helper.h>
>  #include <drm/drm_mipi_dsi.h>
>  #include <drm/drm_panel.h>
>  
> @@ -187,7 +185,6 @@ struct panel_simple {
>  
>  	struct regulator *supply;
>  	struct i2c_adapter *ddc;
> -	struct drm_dp_aux *aux;
>  
>  	struct gpio_desc *enable_gpio;
>  	struct gpio_desc *hpd_gpio;
> @@ -660,8 +657,7 @@ static void panel_simple_parse_panel_timing_node(struct device *dev,
>  		dev_err(dev, "Reject override mode: No display_timing found\n");
>  }
>  
> -static int panel_simple_probe(struct device *dev, const struct panel_desc *desc,
> -			      struct drm_dp_aux *aux)
> +static int panel_simple_probe(struct device *dev, const struct panel_desc *desc)
>  {
>  	struct panel_simple *panel;
>  	struct display_timing dt;
> @@ -677,7 +673,6 @@ static int panel_simple_probe(struct device *dev, const struct panel_desc *desc,
>  	panel->enabled = false;
>  	panel->prepared_time = 0;
>  	panel->desc = desc;
> -	panel->aux = aux;
>  
>  	panel->no_hpd = of_property_read_bool(dev->of_node, "no-hpd");
>  	if (!panel->no_hpd) {
> @@ -712,8 +707,6 @@ static int panel_simple_probe(struct device *dev, const struct panel_desc *desc,
>  
>  		if (!panel->ddc)
>  			return -EPROBE_DEFER;
> -	} else if (aux) {
> -		panel->ddc = &aux->ddc;
>  	}
>  
>  	if (desc == &panel_dpi) {
> @@ -749,9 +742,9 @@ static int panel_simple_probe(struct device *dev, const struct panel_desc *desc,
>  			desc->bpc != 8);
>  		break;
>  	case DRM_MODE_CONNECTOR_eDP:
> -		if (desc->bpc != 6 && desc->bpc != 8 && desc->bpc != 10)
> -			dev_warn(dev, "Expected bpc in {6,8,10} but got: %u\n", desc->bpc);
> -		break;
> +		dev_warn(dev, "eDP panels moved to panel-simple-edp\n");
> +		err = -EINVAL;
> +		goto free_ddc;
>  	case DRM_MODE_CONNECTOR_DSI:
>  		if (desc->bpc != 6 && desc->bpc != 8)
>  			dev_warn(dev, "Expected bpc in {6,8} but got: %u\n", desc->bpc);
> @@ -798,15 +791,6 @@ static int panel_simple_probe(struct device *dev, const struct panel_desc *desc,
>  	if (err)
>  		goto disable_pm_runtime;
>  
> -	if (!panel->base.backlight && panel->aux) {
> -		pm_runtime_get_sync(dev);
> -		err = drm_panel_dp_aux_backlight(&panel->base, panel->aux);
> -		pm_runtime_mark_last_busy(dev);
> -		pm_runtime_put_autosuspend(dev);
> -		if (err)
> -			goto disable_pm_runtime;
> -	}
> -
>  	drm_panel_add(&panel->base);
>  
>  	return 0;
> @@ -815,7 +799,7 @@ static int panel_simple_probe(struct device *dev, const struct panel_desc *desc,
>  	pm_runtime_dont_use_autosuspend(dev);
>  	pm_runtime_disable(dev);
>  free_ddc:
> -	if (panel->ddc && (!panel->aux || panel->ddc != &panel->aux->ddc))
> +	if (panel->ddc)
>  		put_device(&panel->ddc->dev);
>  
>  	return err;
> @@ -831,7 +815,7 @@ static int panel_simple_remove(struct device *dev)
>  
>  	pm_runtime_dont_use_autosuspend(dev);
>  	pm_runtime_disable(dev);
> -	if (panel->ddc && (!panel->aux || panel->ddc != &panel->aux->ddc))
> +	if (panel->ddc)
>  		put_device(&panel->ddc->dev);
>  
>  	return 0;
> @@ -1015,63 +999,6 @@ static const struct panel_desc auo_b101xtn01 = {
>  	},
>  };
>  
> -static const struct drm_display_mode auo_b116xak01_mode = {
> -	.clock = 69300,
> -	.hdisplay = 1366,
> -	.hsync_start = 1366 + 48,
> -	.hsync_end = 1366 + 48 + 32,
> -	.htotal = 1366 + 48 + 32 + 10,
> -	.vdisplay = 768,
> -	.vsync_start = 768 + 4,
> -	.vsync_end = 768 + 4 + 6,
> -	.vtotal = 768 + 4 + 6 + 15,
> -	.flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
> -};
> -
> -static const struct panel_desc auo_b116xak01 = {
> -	.modes = &auo_b116xak01_mode,
> -	.num_modes = 1,
> -	.bpc = 6,
> -	.size = {
> -		.width = 256,
> -		.height = 144,
> -	},
> -	.delay = {
> -		.hpd_absent_delay = 200,
> -	},
> -	.bus_format = MEDIA_BUS_FMT_RGB666_1X18,
> -	.connector_type = DRM_MODE_CONNECTOR_eDP,
> -};
> -
> -static const struct drm_display_mode auo_b116xw03_mode = {
> -	.clock = 70589,
> -	.hdisplay = 1366,
> -	.hsync_start = 1366 + 40,
> -	.hsync_end = 1366 + 40 + 40,
> -	.htotal = 1366 + 40 + 40 + 32,
> -	.vdisplay = 768,
> -	.vsync_start = 768 + 10,
> -	.vsync_end = 768 + 10 + 12,
> -	.vtotal = 768 + 10 + 12 + 6,
> -	.flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
> -};
> -
> -static const struct panel_desc auo_b116xw03 = {
> -	.modes = &auo_b116xw03_mode,
> -	.num_modes = 1,
> -	.bpc = 6,
> -	.size = {
> -		.width = 256,
> -		.height = 144,
> -	},
> -	.delay = {
> -		.enable = 400,
> -	},
> -	.bus_flags = DRM_BUS_FLAG_SYNC_DRIVE_NEGEDGE,
> -	.bus_format = MEDIA_BUS_FMT_RGB666_1X18,
> -	.connector_type = DRM_MODE_CONNECTOR_eDP,
> -};
> -
>  static const struct drm_display_mode auo_b133xtn01_mode = {
>  	.clock = 69500,
>  	.hdisplay = 1366,
> @@ -1094,36 +1021,6 @@ static const struct panel_desc auo_b133xtn01 = {
>  	},
>  };
>  
> -static const struct drm_display_mode auo_b133han05_mode = {
> -	.clock = 142600,
> -	.hdisplay = 1920,
> -	.hsync_start = 1920 + 58,
> -	.hsync_end = 1920 + 58 + 42,
> -	.htotal = 1920 + 58 + 42 + 60,
> -	.vdisplay = 1080,
> -	.vsync_start = 1080 + 3,
> -	.vsync_end = 1080 + 3 + 5,
> -	.vtotal = 1080 + 3 + 5 + 54,
> -};
> -
> -static const struct panel_desc auo_b133han05 = {
> -	.modes = &auo_b133han05_mode,
> -	.num_modes = 1,
> -	.bpc = 8,
> -	.size = {
> -		.width = 293,
> -		.height = 165,
> -	},
> -	.delay = {
> -		.prepare = 100,
> -		.enable = 20,
> -		.unprepare = 50,
> -	},
> -	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
> -	.bus_flags = DRM_BUS_FLAG_DATA_MSB_TO_LSB,
> -	.connector_type = DRM_MODE_CONNECTOR_eDP,
> -};
> -
>  static const struct drm_display_mode auo_b133htn01_mode = {
>  	.clock = 150660,
>  	.hdisplay = 1920,
> @@ -1151,36 +1048,6 @@ static const struct panel_desc auo_b133htn01 = {
>  	},
>  };
>  
> -static const struct drm_display_mode auo_b140han06_mode = {
> -	.clock = 141000,
> -	.hdisplay = 1920,
> -	.hsync_start = 1920 + 16,
> -	.hsync_end = 1920 + 16 + 16,
> -	.htotal = 1920 + 16 + 16 + 152,
> -	.vdisplay = 1080,
> -	.vsync_start = 1080 + 3,
> -	.vsync_end = 1080 + 3 + 14,
> -	.vtotal = 1080 + 3 + 14 + 19,
> -};
> -
> -static const struct panel_desc auo_b140han06 = {
> -	.modes = &auo_b140han06_mode,
> -	.num_modes = 1,
> -	.bpc = 8,
> -	.size = {
> -		.width = 309,
> -		.height = 174,
> -	},
> -	.delay = {
> -		.prepare = 100,
> -		.enable = 20,
> -		.unprepare = 50,
> -	},
> -	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
> -	.bus_flags = DRM_BUS_FLAG_DATA_MSB_TO_LSB,
> -	.connector_type = DRM_MODE_CONNECTOR_eDP,
> -};
> -
>  static const struct display_timing auo_g070vvn01_timings = {
>  	.pixelclock = { 33300000, 34209000, 45000000 },
>  	.hactive = { 800, 800, 800 },
> @@ -1564,129 +1431,6 @@ static const struct panel_desc boe_nv101wxmn51 = {
>  	},
>  };
>  
> -static const struct drm_display_mode boe_nv110wtm_n61_modes[] = {
> -	{
> -		.clock = 207800,
> -		.hdisplay = 2160,
> -		.hsync_start = 2160 + 48,
> -		.hsync_end = 2160 + 48 + 32,
> -		.htotal = 2160 + 48 + 32 + 100,
> -		.vdisplay = 1440,
> -		.vsync_start = 1440 + 3,
> -		.vsync_end = 1440 + 3 + 6,
> -		.vtotal = 1440 + 3 + 6 + 31,
> -		.flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_NVSYNC,
> -	},
> -	{
> -		.clock = 138500,
> -		.hdisplay = 2160,
> -		.hsync_start = 2160 + 48,
> -		.hsync_end = 2160 + 48 + 32,
> -		.htotal = 2160 + 48 + 32 + 100,
> -		.vdisplay = 1440,
> -		.vsync_start = 1440 + 3,
> -		.vsync_end = 1440 + 3 + 6,
> -		.vtotal = 1440 + 3 + 6 + 31,
> -		.flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_NVSYNC,
> -	},
> -};
> -
> -static const struct panel_desc boe_nv110wtm_n61 = {
> -	.modes = boe_nv110wtm_n61_modes,
> -	.num_modes = ARRAY_SIZE(boe_nv110wtm_n61_modes),
> -	.bpc = 8,
> -	.size = {
> -		.width = 233,
> -		.height = 155,
> -	},
> -	.delay = {
> -		.hpd_absent_delay = 200,
> -		.prepare_to_enable = 80,
> -		.enable = 50,
> -		.unprepare = 500,
> -	},
> -	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
> -	.bus_flags = DRM_BUS_FLAG_DATA_MSB_TO_LSB,
> -	.connector_type = DRM_MODE_CONNECTOR_eDP,
> -};
> -
> -/* Also used for boe_nv133fhm_n62 */
> -static const struct drm_display_mode boe_nv133fhm_n61_modes = {
> -	.clock = 147840,
> -	.hdisplay = 1920,
> -	.hsync_start = 1920 + 48,
> -	.hsync_end = 1920 + 48 + 32,
> -	.htotal = 1920 + 48 + 32 + 200,
> -	.vdisplay = 1080,
> -	.vsync_start = 1080 + 3,
> -	.vsync_end = 1080 + 3 + 6,
> -	.vtotal = 1080 + 3 + 6 + 31,
> -	.flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_NVSYNC,
> -};
> -
> -/* Also used for boe_nv133fhm_n62 */
> -static const struct panel_desc boe_nv133fhm_n61 = {
> -	.modes = &boe_nv133fhm_n61_modes,
> -	.num_modes = 1,
> -	.bpc = 6,
> -	.size = {
> -		.width = 294,
> -		.height = 165,
> -	},
> -	.delay = {
> -		/*
> -		 * When power is first given to the panel there's a short
> -		 * spike on the HPD line.  It was explained that this spike
> -		 * was until the TCON data download was complete.  On
> -		 * one system this was measured at 8 ms.  We'll put 15 ms
> -		 * in the prepare delay just to be safe and take it away
> -		 * from the hpd_absent_delay (which would otherwise be 200 ms)
> -		 * to handle this.  That means:
> -		 * - If HPD isn't hooked up you still have 200 ms delay.
> -		 * - If HPD is hooked up we won't try to look at it for the
> -		 *   first 15 ms.
> -		 */
> -		.prepare = 15,
> -		.hpd_absent_delay = 185,
> -
> -		.unprepare = 500,
> -	},
> -	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
> -	.bus_flags = DRM_BUS_FLAG_DATA_MSB_TO_LSB,
> -	.connector_type = DRM_MODE_CONNECTOR_eDP,
> -};
> -
> -static const struct drm_display_mode boe_nv140fhmn49_modes[] = {
> -	{
> -		.clock = 148500,
> -		.hdisplay = 1920,
> -		.hsync_start = 1920 + 48,
> -		.hsync_end = 1920 + 48 + 32,
> -		.htotal = 2200,
> -		.vdisplay = 1080,
> -		.vsync_start = 1080 + 3,
> -		.vsync_end = 1080 + 3 + 5,
> -		.vtotal = 1125,
> -	},
> -};
> -
> -static const struct panel_desc boe_nv140fhmn49 = {
> -	.modes = boe_nv140fhmn49_modes,
> -	.num_modes = ARRAY_SIZE(boe_nv140fhmn49_modes),
> -	.bpc = 6,
> -	.size = {
> -		.width = 309,
> -		.height = 174,
> -	},
> -	.delay = {
> -		.prepare = 210,
> -		.enable = 50,
> -		.unprepare = 160,
> -	},
> -	.bus_format = MEDIA_BUS_FMT_RGB666_1X18,
> -	.connector_type = DRM_MODE_CONNECTOR_eDP,
> -};
> -
>  static const struct drm_display_mode cdtech_s043wq26h_ct7_mode = {
>  	.clock = 9000,
>  	.hdisplay = 480,
> @@ -2609,96 +2353,6 @@ static const struct panel_desc innolux_g121x1_l03 = {
>  	},
>  };
>  
> -static const struct drm_display_mode innolux_n116bca_ea1_mode = {
> -	.clock = 76420,
> -	.hdisplay = 1366,
> -	.hsync_start = 1366 + 136,
> -	.hsync_end = 1366 + 136 + 30,
> -	.htotal = 1366 + 136 + 30 + 60,
> -	.vdisplay = 768,
> -	.vsync_start = 768 + 8,
> -	.vsync_end = 768 + 8 + 12,
> -	.vtotal = 768 + 8 + 12 + 12,
> -	.flags = DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC,
> -};
> -
> -static const struct panel_desc innolux_n116bca_ea1 = {
> -	.modes = &innolux_n116bca_ea1_mode,
> -	.num_modes = 1,
> -	.bpc = 6,
> -	.size = {
> -		.width = 256,
> -		.height = 144,
> -	},
> -	.delay = {
> -		.hpd_absent_delay = 200,
> -		.prepare_to_enable = 80,
> -		.unprepare = 500,
> -	},
> -	.bus_format = MEDIA_BUS_FMT_RGB666_1X18,
> -	.connector_type = DRM_MODE_CONNECTOR_eDP,
> -};
> -
> -/*
> - * Datasheet specifies that at 60 Hz refresh rate:
> - * - total horizontal time: { 1506, 1592, 1716 }
> - * - total vertical time: { 788, 800, 868 }
> - *
> - * ...but doesn't go into exactly how that should be split into a front
> - * porch, back porch, or sync length.  For now we'll leave a single setting
> - * here which allows a bit of tweaking of the pixel clock at the expense of
> - * refresh rate.
> - */
> -static const struct display_timing innolux_n116bge_timing = {
> -	.pixelclock = { 72600000, 76420000, 80240000 },
> -	.hactive = { 1366, 1366, 1366 },
> -	.hfront_porch = { 136, 136, 136 },
> -	.hback_porch = { 60, 60, 60 },
> -	.hsync_len = { 30, 30, 30 },
> -	.vactive = { 768, 768, 768 },
> -	.vfront_porch = { 8, 8, 8 },
> -	.vback_porch = { 12, 12, 12 },
> -	.vsync_len = { 12, 12, 12 },
> -	.flags = DISPLAY_FLAGS_VSYNC_LOW | DISPLAY_FLAGS_HSYNC_LOW,
> -};
> -
> -static const struct panel_desc innolux_n116bge = {
> -	.timings = &innolux_n116bge_timing,
> -	.num_timings = 1,
> -	.bpc = 6,
> -	.size = {
> -		.width = 256,
> -		.height = 144,
> -	},
> -	.bus_format = MEDIA_BUS_FMT_RGB666_1X18,
> -	.connector_type = DRM_MODE_CONNECTOR_eDP,
> -};
> -
> -static const struct drm_display_mode innolux_n125hce_gn1_mode = {
> -	.clock = 162000,
> -	.hdisplay = 1920,
> -	.hsync_start = 1920 + 40,
> -	.hsync_end = 1920 + 40 + 40,
> -	.htotal = 1920 + 40 + 40 + 80,
> -	.vdisplay = 1080,
> -	.vsync_start = 1080 + 4,
> -	.vsync_end = 1080 + 4 + 4,
> -	.vtotal = 1080 + 4 + 4 + 24,
> -};
> -
> -static const struct panel_desc innolux_n125hce_gn1 = {
> -	.modes = &innolux_n125hce_gn1_mode,
> -	.num_modes = 1,
> -	.bpc = 8,
> -	.size = {
> -		.width = 276,
> -		.height = 155,
> -	},
> -	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
> -	.bus_flags = DRM_BUS_FLAG_DATA_MSB_TO_LSB,
> -	.connector_type = DRM_MODE_CONNECTOR_eDP,
> -};
> -
>  static const struct drm_display_mode innolux_n156bge_l21_mode = {
>  	.clock = 69300,
>  	.hdisplay = 1366,
> @@ -2773,64 +2427,6 @@ static const struct panel_desc innolux_zj070na_01p = {
>  	},
>  };
>  
> -static const struct drm_display_mode ivo_m133nwf4_r0_mode = {
> -	.clock = 138778,
> -	.hdisplay = 1920,
> -	.hsync_start = 1920 + 24,
> -	.hsync_end = 1920 + 24 + 48,
> -	.htotal = 1920 + 24 + 48 + 88,
> -	.vdisplay = 1080,
> -	.vsync_start = 1080 + 3,
> -	.vsync_end = 1080 + 3 + 12,
> -	.vtotal = 1080 + 3 + 12 + 17,
> -	.flags = DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC,
> -};
> -
> -static const struct panel_desc ivo_m133nwf4_r0 = {
> -	.modes = &ivo_m133nwf4_r0_mode,
> -	.num_modes = 1,
> -	.bpc = 8,
> -	.size = {
> -		.width = 294,
> -		.height = 165,
> -	},
> -	.delay = {
> -		.hpd_absent_delay = 200,
> -		.unprepare = 500,
> -	},
> -	.bus_format = MEDIA_BUS_FMT_RGB888_1X24,
> -	.bus_flags = DRM_BUS_FLAG_DATA_MSB_TO_LSB,
> -	.connector_type = DRM_MODE_CONNECTOR_eDP,
> -};
> -
> -static const struct drm_display_mode kingdisplay_kd116n21_30nv_a010_mode = {
> -	.clock = 81000,
> -	.hdisplay = 1366,
> -	.hsync_start = 1366 + 40,
> -	.hsync_end = 1366 + 40 + 32,
> -	.htotal = 1366 + 40 + 32 + 62,
> -	.vdisplay = 768,
> -	.vsync_start = 768 + 5,
> -	.vsync_end = 768 + 5 + 5,
> -	.vtotal = 768 + 5 + 5 + 122,
> -	.flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
> -};
> -
> -static const struct panel_desc kingdisplay_kd116n21_30nv_a010 = {
> -	.modes = &kingdisplay_kd116n21_30nv_a010_mode,
> -	.num_modes = 1,
> -	.bpc = 6,
> -	.size = {
> -		.width = 256,
> -		.height = 144,
> -	},
> -	.delay = {
> -		.hpd_absent_delay = 200,
> -	},
> -	.bus_format = MEDIA_BUS_FMT_RGB666_1X18,
> -	.connector_type = DRM_MODE_CONNECTOR_eDP,
> -};
> -
>  static const struct display_timing koe_tx14d24vm1bpa_timing = {
>  	.pixelclock = { 5580000, 5850000, 6200000 },
>  	.hactive = { 320, 320, 320 },
> @@ -3025,29 +2621,6 @@ static const struct panel_desc lg_lp097qx1_spa1 = {
>  	},
>  };
>  
> -static const struct drm_display_mode lg_lp120up1_mode = {
> -	.clock = 162300,
> -	.hdisplay = 1920,
> -	.hsync_start = 1920 + 40,
> -	.hsync_end = 1920 + 40 + 40,
> -	.htotal = 1920 + 40 + 40+ 80,
> -	.vdisplay = 1280,
> -	.vsync_start = 1280 + 4,
> -	.vsync_end = 1280 + 4 + 4,
> -	.vtotal = 1280 + 4 + 4 + 12,
> -};
> -
> -static const struct panel_desc lg_lp120up1 = {
> -	.modes = &lg_lp120up1_mode,
> -	.num_modes = 1,
> -	.bpc = 8,
> -	.size = {
> -		.width = 267,
> -		.height = 183,
> -	},
> -	.connector_type = DRM_MODE_CONNECTOR_eDP,
> -};
> -
>  static const struct drm_display_mode lg_lp129qe_mode = {
>  	.clock = 285250,
>  	.hdisplay = 2560,
> @@ -3330,49 +2903,6 @@ static const struct panel_desc netron_dy_e231732 = {
>  	.bus_format = MEDIA_BUS_FMT_RGB666_1X18,
>  };
>  
> -static const struct drm_display_mode neweast_wjfh116008a_modes[] = {
> -	{
> -		.clock = 138500,
> -		.hdisplay = 1920,
> -		.hsync_start = 1920 + 48,
> -		.hsync_end = 1920 + 48 + 32,
> -		.htotal = 1920 + 48 + 32 + 80,
> -		.vdisplay = 1080,
> -		.vsync_start = 1080 + 3,
> -		.vsync_end = 1080 + 3 + 5,
> -		.vtotal = 1080 + 3 + 5 + 23,
> -		.flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
> -	}, {
> -		.clock = 110920,
> -		.hdisplay = 1920,
> -		.hsync_start = 1920 + 48,
> -		.hsync_end = 1920 + 48 + 32,
> -		.htotal = 1920 + 48 + 32 + 80,
> -		.vdisplay = 1080,
> -		.vsync_start = 1080 + 3,
> -		.vsync_end = 1080 + 3 + 5,
> -		.vtotal = 1080 + 3 + 5 + 23,
> -		.flags = DRM_MODE_FLAG_NVSYNC | DRM_MODE_FLAG_NHSYNC,
> -	}
> -};
> -
> -static const struct panel_desc neweast_wjfh116008a = {
> -	.modes = neweast_wjfh116008a_modes,
> -	.num_modes = 2,
> -	.bpc = 6,
> -	.size = {
> -		.width = 260,
> -		.height = 150,
> -	},
> -	.delay = {
> -		.prepare = 110,
> -		.enable = 20,
> -		.unprepare = 500,
> -	},
> -	.bus_format = MEDIA_BUS_FMT_RGB666_1X18,
> -	.connector_type = DRM_MODE_CONNECTOR_eDP,
> -};
> -
>  static const struct drm_display_mode newhaven_nhd_43_480272ef_atxl_mode = {
>  	.clock = 9000,
>  	.hdisplay = 480,
> @@ -4489,21 +4019,9 @@ static const struct of_device_id platform_of_match[] = {
>  	}, {
>  		.compatible = "auo,b101xtn01",
>  		.data = &auo_b101xtn01,
> -	}, {
> -		.compatible = "auo,b116xa01",
> -		.data = &auo_b116xak01,
> -	}, {
> -		.compatible = "auo,b116xw03",
> -		.data = &auo_b116xw03,
> -	}, {
> -		.compatible = "auo,b133han05",
> -		.data = &auo_b133han05,
>  	}, {
>  		.compatible = "auo,b133htn01",
>  		.data = &auo_b133htn01,
> -	}, {
> -		.compatible = "auo,b140han06",
> -		.data = &auo_b140han06,
>  	}, {
>  		.compatible = "auo,b133xtn01",
>  		.data = &auo_b133xtn01,
> @@ -4549,18 +4067,6 @@ static const struct of_device_id platform_of_match[] = {
>  	}, {
>  		.compatible = "boe,nv101wxmn51",
>  		.data = &boe_nv101wxmn51,
> -	}, {
> -		.compatible = "boe,nv110wtm-n61",
> -		.data = &boe_nv110wtm_n61,
> -	}, {
> -		.compatible = "boe,nv133fhm-n61",
> -		.data = &boe_nv133fhm_n61,
> -	}, {
> -		.compatible = "boe,nv133fhm-n62",
> -		.data = &boe_nv133fhm_n61,
> -	}, {
> -		.compatible = "boe,nv140fhmn49",
> -		.data = &boe_nv140fhmn49,
>  	}, {
>  		.compatible = "cdtech,s043wq26h-ct7",
>  		.data = &cdtech_s043wq26h_ct7,
> @@ -4672,15 +4178,6 @@ static const struct of_device_id platform_of_match[] = {
>  	}, {
>  		.compatible = "innolux,g121x1-l03",
>  		.data = &innolux_g121x1_l03,
> -	}, {
> -		.compatible = "innolux,n116bca-ea1",
> -		.data = &innolux_n116bca_ea1,
> -	}, {
> -		.compatible = "innolux,n116bge",
> -		.data = &innolux_n116bge,
> -	}, {
> -		.compatible = "innolux,n125hce-gn1",
> -		.data = &innolux_n125hce_gn1,
>  	}, {
>  		.compatible = "innolux,n156bge-l21",
>  		.data = &innolux_n156bge_l21,
> @@ -4690,12 +4187,6 @@ static const struct of_device_id platform_of_match[] = {
>  	}, {
>  		.compatible = "innolux,zj070na-01p",
>  		.data = &innolux_zj070na_01p,
> -	}, {
> -		.compatible = "ivo,m133nwf4-r0",
> -		.data = &ivo_m133nwf4_r0,
> -	}, {
> -		.compatible = "kingdisplay,kd116n21-30nv-a010",
> -		.data = &kingdisplay_kd116n21_30nv_a010,
>  	}, {
>  		.compatible = "koe,tx14d24vm1bpa",
>  		.data = &koe_tx14d24vm1bpa,
> @@ -4720,9 +4211,6 @@ static const struct of_device_id platform_of_match[] = {
>  	}, {
>  		.compatible = "lg,lp097qx1-spa1",
>  		.data = &lg_lp097qx1_spa1,
> -	}, {
> -		.compatible = "lg,lp120up1",
> -		.data = &lg_lp120up1,
>  	}, {
>  		.compatible = "lg,lp129qe",
>  		.data = &lg_lp129qe,
> @@ -4756,9 +4244,6 @@ static const struct of_device_id platform_of_match[] = {
>  	}, {
>  		.compatible = "netron-dy,e231732",
>  		.data = &netron_dy_e231732,
> -	}, {
> -		.compatible = "neweast,wjfh116008a",
> -		.data = &neweast_wjfh116008a,
>  	}, {
>  		.compatible = "newhaven,nhd-4.3-480272ef-atxl",
>  		.data = &newhaven_nhd_43_480272ef_atxl,
> @@ -4918,7 +4403,7 @@ static int panel_simple_platform_probe(struct platform_device *pdev)
>  	if (!id)
>  		return -ENODEV;
>  
> -	return panel_simple_probe(&pdev->dev, id->data, NULL);
> +	return panel_simple_probe(&pdev->dev, id->data);
>  }
>  
>  static int panel_simple_platform_remove(struct platform_device *pdev)
> @@ -5198,7 +4683,7 @@ static int panel_simple_dsi_probe(struct mipi_dsi_device *dsi)
>  
>  	desc = id->data;
>  
> -	err = panel_simple_probe(&dsi->dev, &desc->desc, NULL);
> +	err = panel_simple_probe(&dsi->dev, &desc->desc);
>  	if (err < 0)
>  		return err;
>  
> @@ -5243,38 +4728,6 @@ static struct mipi_dsi_driver panel_simple_dsi_driver = {
>  	.shutdown = panel_simple_dsi_shutdown,
>  };
>  
> -static int panel_simple_dp_aux_ep_probe(struct dp_aux_ep_device *aux_ep)
> -{
> -	const struct of_device_id *id;
> -
> -	id = of_match_node(platform_of_match, aux_ep->dev.of_node);
> -	if (!id)
> -		return -ENODEV;
> -
> -	return panel_simple_probe(&aux_ep->dev, id->data, aux_ep->aux);
> -}
> -
> -static void panel_simple_dp_aux_ep_remove(struct dp_aux_ep_device *aux_ep)
> -{
> -	panel_simple_remove(&aux_ep->dev);
> -}
> -
> -static void panel_simple_dp_aux_ep_shutdown(struct dp_aux_ep_device *aux_ep)
> -{
> -	panel_simple_shutdown(&aux_ep->dev);
> -}
> -
> -static struct dp_aux_ep_driver panel_simple_dp_aux_ep_driver = {
> -	.driver = {
> -		.name = "panel-simple-dp-aux",
> -		.of_match_table = platform_of_match,	/* Same as platform one! */
> -		.pm = &panel_simple_pm_ops,
> -	},
> -	.probe = panel_simple_dp_aux_ep_probe,
> -	.remove = panel_simple_dp_aux_ep_remove,
> -	.shutdown = panel_simple_dp_aux_ep_shutdown,
> -};
> -
>  static int __init panel_simple_init(void)
>  {
>  	int err;
> @@ -5283,21 +4736,14 @@ static int __init panel_simple_init(void)
>  	if (err < 0)
>  		return err;
>  
> -	err = dp_aux_dp_driver_register(&panel_simple_dp_aux_ep_driver);
> -	if (err < 0)
> -		goto err_did_platform_register;
> -
>  	if (IS_ENABLED(CONFIG_DRM_MIPI_DSI)) {
>  		err = mipi_dsi_driver_register(&panel_simple_dsi_driver);
>  		if (err < 0)
> -			goto err_did_aux_ep_register;
> +			goto err_did_platform_register;
>  	}
>  
>  	return 0;
>  
> -err_did_aux_ep_register:
> -	dp_aux_dp_driver_unregister(&panel_simple_dp_aux_ep_driver);
> -
>  err_did_platform_register:
>  	platform_driver_unregister(&panel_simple_platform_driver);
>  
> @@ -5310,11 +4756,10 @@ static void __exit panel_simple_exit(void)
>  	if (IS_ENABLED(CONFIG_DRM_MIPI_DSI))
>  		mipi_dsi_driver_unregister(&panel_simple_dsi_driver);
>  
> -	dp_aux_dp_driver_unregister(&panel_simple_dp_aux_ep_driver);
>  	platform_driver_unregister(&panel_simple_platform_driver);
>  }
>  module_exit(panel_simple_exit);
>  
>  MODULE_AUTHOR("Thierry Reding <treding@xxxxxxxxxx>");
> -MODULE_DESCRIPTION("DRM Driver for Simple Panels");
> +MODULE_DESCRIPTION("DRM Driver for Simple non-eDP Panels");

Well, I do not consider eDP panels simple. So the old description was
fine for me.

>  MODULE_LICENSE("GPL and additional rights");
> -- 
> 2.33.0.259.gc128427fd7-goog




[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux