[PATCH v2 3/3] drm/mediatek: fine tune the dsi panel's power sequence

[Jitao Shi <jitao.shi@xxxxxxxxxxxx>]

Add the drm_panel_prepare_power and drm_panel_unprepare_power control.
Turn on panel power(drm_panel_prepare_power) and control before dsi
enable. And then dsi enable, send dcs cmd in drm_panel_prepare, last
turn on backlight.

Most dsi panels, have five steps when poweron.

1. turn on dsi signal to LP11   --> dsi host's action
2. turn on the power supplies,  --> panel's action
3. send the DCS  cmd to panel   --> panel's action
4. start send video stream      --> dsi host's action
5. turn on backlight.           --> panel's action

we put "turn on the power supplies" and "send the DCS  cmd to panel" in
panel_prepare. And "turn on backlight" in panel_enable.

But some other panels has a special poweron sequence as the following.

1. turn on the power supplies,  --> panel's action
2. turn on dsi signal to LP11   --> dsi host's action
3. send the DCS  cmd to panel   --> panel's action
4. start send video stream      --> dsi host's action
5. turn on backlight.           --> panel's action

panel's actions are divided into three parts.

So I add a new api "drm_panel_prepare_power/rm_panel_unprepare_power" to
control the sequence.

Signed-off-by: Jitao Shi <jitao.shi@xxxxxxxxxxxx>
---
 drivers/gpu/drm/mediatek/mtk_dsi.c | 29 ++++++++++++++++++++++++-----
 1 file changed, 24 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c b/drivers/gpu/drm/mediatek/mtk_dsi.c
index ae403c67cbd9..24f89a1dd421 100644
--- a/drivers/gpu/drm/mediatek/mtk_dsi.c
+++ b/drivers/gpu/drm/mediatek/mtk_dsi.c
@@ -184,6 +184,7 @@ struct mtk_dsi {
 	struct drm_encoder encoder;
 	struct drm_bridge bridge;
 	struct drm_bridge *next_bridge;
+	struct drm_panel *panel;
 	struct drm_connector *connector;
 	struct phy *phy;
 
@@ -619,10 +620,18 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi)
 	dsi->data_rate = DIV_ROUND_UP_ULL(dsi->vm.pixelclock * bit_per_pixel,
 					  dsi->lanes);
 
+	if (dsi->panel) {
+		ret = panel_bridge_prepare_power(dsi->next_bridge)
+		if (ret) {
+			DRM_INFO("can't prepare power the panel\n");
+			goto err_refcount;
+		}
+	}
+
 	ret = clk_set_rate(dsi->hs_clk, dsi->data_rate);
 	if (ret < 0) {
 		dev_err(dev, "Failed to set data rate: %d\n", ret);
-		goto err_refcount;
+		goto err_prepare_power;
 	}
 
 	phy_power_on(dsi->phy);
@@ -665,6 +674,11 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi)
 	clk_disable_unprepare(dsi->engine_clk);
 err_phy_power_off:
 	phy_power_off(dsi->phy);
+err_prepare_power:
+	if (dsi->panel) {
+		if (panel_bridge_unprepare_power(dsi->next_bridge))
+			dev_err(dev, "Can't unprepare power the panel\n");
+	}
 err_refcount:
 	dsi->refcount--;
 	return ret;
@@ -698,6 +712,12 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi)
 	clk_disable_unprepare(dsi->digital_clk);
 
 	phy_power_off(dsi->phy);
+
+	if (dsi->panel) {
+		ret = panel_bridge_unprepare_power(dsi->next_bridge);
+		if (ret)
+			dev_err(dev, "Can't unprepare power the panel ret:%d\n", ret);
+	}
 }
 
 static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
@@ -1001,7 +1021,6 @@ static int mtk_dsi_probe(struct platform_device *pdev)
 {
 	struct mtk_dsi *dsi;
 	struct device *dev = &pdev->dev;
-	struct drm_panel *panel;
 	struct resource *regs;
 	int irq_num;
 	int ret;
@@ -1019,12 +1038,12 @@ static int mtk_dsi_probe(struct platform_device *pdev)
 	}
 
 	ret = drm_of_find_panel_or_bridge(dev->of_node, 0, 0,
-					  &panel, &dsi->next_bridge);
+					  &dsi->panel, &dsi->next_bridge);
 	if (ret)
 		goto err_unregister_host;
 
-	if (panel) {
-		dsi->next_bridge = devm_drm_panel_bridge_add(dev, panel);
+	if (dsi->panel) {
+		dsi->next_bridge = devm_drm_panel_bridge_add(dev, dsi->panel);
 		if (IS_ERR(dsi->next_bridge)) {
 			ret = PTR_ERR(dsi->next_bridge);
 			goto err_unregister_host;
-- 
2.25.1