DG2 has some changes to the expected modesetting sequences when compared
to gen12. Adjust our driver logic accordingly. Although the DP
sequence is pretty similar to TGL's, there are some steps that change,
so let's split the handling for that out into a separate function.
Bspec: 54128
Cc: Lucas De Marchi <lucas.demarchi@xxxxxxxxx>
Cc: Anusha Srivatsa <anusha.srivatsa@xxxxxxxxx>
Signed-off-by: Matt Roper <matthew.d.roper@xxxxxxxxx>
---
drivers/gpu/drm/i915/display/intel_ddi.c | 135 +++++++++++++++++++++--
1 file changed, 127 insertions(+), 8 deletions(-)
diff --git a/drivers/gpu/drm/i915/display/intel_ddi.c b/drivers/gpu/drm/i915/display/intel_ddi.c
index ade03cf41caa..5499a2975a0e 100644
--- a/drivers/gpu/drm/i915/display/intel_ddi.c
+++ b/drivers/gpu/drm/i915/display/intel_ddi.c
@@ -172,14 +172,22 @@ void intel_wait_ddi_buf_idle(struct drm_i915_private *dev_priv,
static void intel_wait_ddi_buf_active(struct drm_i915_private *dev_priv,
enum port port)
{
+ int ret;
+
/* Wait > 518 usecs for DDI_BUF_CTL to be non idle */
if (DISPLAY_VER(dev_priv) < 10) {
usleep_range(518, 1000);
return;
}
- if (wait_for_us(!(intel_de_read(dev_priv, DDI_BUF_CTL(port)) &
- DDI_BUF_IS_IDLE), 500))
+ if (IS_DG2(dev_priv))
+ ret = wait_for_us(!(intel_de_read(dev_priv, DDI_BUF_CTL(port)) &
+ DDI_BUF_IS_IDLE), 1200);
+ else
+ ret = wait_for_us(!(intel_de_read(dev_priv, DDI_BUF_CTL(port)) &
+ DDI_BUF_IS_IDLE), 500);
+
+ if (ret)
drm_err(&dev_priv->drm, "Timeout waiting for DDI BUF %c to get active\n",
port_name(port));
}
@@ -2207,7 +2215,7 @@ void intel_ddi_sanitize_encoder_pll_mapping(struct intel_encoder *encoder)
ddi_clk_needed = false;
}
- if (ddi_clk_needed || !encoder->disable_clock ||
+ if (ddi_clk_needed || !encoder->is_clock_enabled ||
!encoder->is_clock_enabled(encoder))
return;
@@ -2488,6 +2496,116 @@ static void intel_ddi_mso_configure(const struct intel_crtc_state *crtc_state)
OVERLAP_PIXELS_MASK, dss1);
}
+static void dg2_ddi_pre_enable_dp(struct intel_atomic_state *state,
+ struct intel_encoder *encoder,
+ const struct intel_crtc_state *crtc_state,
+ const struct drm_connector_state *conn_state)
+{
+ struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
+ struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
+ enum phy phy = intel_port_to_phy(dev_priv, encoder->port);
+ struct intel_digital_port *dig_port = enc_to_dig_port(encoder);
+ bool is_mst = intel_crtc_has_type(crtc_state, INTEL_OUTPUT_DP_MST);
+ int level = intel_ddi_dp_level(intel_dp);
+
+ intel_dp_set_link_params(intel_dp, crtc_state->port_clock,
+ crtc_state->lane_count);
+
+ /*
+ * 1. Enable Power Wells
+ *
+ * This was handled at the beginning of intel_atomic_commit_tail(),
+ * before we called down into this function.
+ */
+
+ /* 2. Enable Panel Power if PPS is required */
+ intel_pps_on(intel_dp);
+
+ /*
+ * 3. Enable the port PLL.
+ */
+ intel_ddi_enable_clock(encoder, crtc_state);
+
+ /* 4. Enable IO power */
+ if (!intel_phy_is_tc(dev_priv, phy) ||
+ dig_port->tc_mode != TC_PORT_TBT_ALT)
+ dig_port->ddi_io_wakeref = intel_display_power_get(dev_priv,
+ dig_port->ddi_io_power_domain);
+
+ /*
+ * 5. The rest of the below are substeps under the bspec's "Enable and
+ * Train Display Port" step. Note that steps that are specific to
+ * MST will be handled by intel_mst_pre_enable_dp() before/after it
+ * calls into this function. Also intel_mst_pre_enable_dp() only calls
+ * us when active_mst_links==0, so any steps designated for "single
+ * stream or multi-stream master transcoder" can just be performed
+ * unconditionally here.
+ */
+
+ /*
+ * 5.a Configure Transcoder Clock Select to direct the Port clock to the
+ * Transcoder.
+ */
+ intel_ddi_enable_pipe_clock(encoder, crtc_state);
+
+ /* 5.b Not relevant to i915 for now */
+
+ /*
+ * 5.c Configure TRANS_DDI_FUNC_CTL DDI Select, DDI Mode Select & MST
+ * Transport Select
+ */
+ intel_ddi_config_transcoder_func(encoder, crtc_state);
+
+ /*
+ * 5.d Configure & enable DP_TP_CTL with link training pattern 1
+ * selected
+ *
+ * This will be handled by the intel_dp_start_link_train() farther
+ * down this function.
+ */
+
+ /* 5.e Configure voltage swing and related IO settings */
+ intel_snps_phy_ddi_vswing_sequence(encoder, level);
+
+ /*
+ * 5.f Configure and enable DDI_BUF_CTL
+ * 5.g Wait for DDI_BUF_CTL DDI Idle Status = 0b (Not Idle), timeout
+ * after 1200 us.
+ *
+ * We only configure what the register value will be here. Actual
+ * enabling happens during link training farther down.
+ */
+ intel_ddi_init_dp_buf_reg(encoder, crtc_state);
+
+ if (!is_mst)
+ intel_dp_set_power(intel_dp, DP_SET_POWER_D0);
+
+ intel_dp_sink_set_decompression_state(intel_dp, crtc_state, true);
+ /*
+ * DDI FEC: "anticipates enabling FEC encoding sets the FEC_READY bit
+ * in the FEC_CONFIGURATION register to 1 before initiating link
+ * training
+ */
+ intel_dp_sink_set_fec_ready(intel_dp, crtc_state);
+
+ /*
+ * 5.h Follow DisplayPort specification training sequence (see notes for
+ * failure handling)
+ * 5.i If DisplayPort multi-stream - Set DP_TP_CTL link training to Idle
+ * Pattern, wait for 5 idle patterns (DP_TP_STATUS Min_Idles_Sent)
+ * (timeout after 800 us)
+ */
+ intel_dp_start_link_train(intel_dp, crtc_state);
+
+ /* 5.j Set DP_TP_CTL link training to Normal */
+ if (!is_trans_port_sync_mode(crtc_state))
+ intel_dp_stop_link_train(intel_dp, crtc_state);
+
+ /* 5.k Configure and enable FEC if needed */
+ intel_ddi_enable_fec(encoder, crtc_state);
+ intel_dsc_enable(encoder, crtc_state);
+}
+
static void tgl_ddi_pre_enable_dp(struct intel_atomic_state *state,
struct intel_encoder *encoder,
const struct intel_crtc_state *crtc_state,
@@ -2573,10 +2691,7 @@ static void tgl_ddi_pre_enable_dp(struct intel_atomic_state *state,
*/
/* 7.e Configure voltage swing and related IO settings */
- if (IS_DG2(dev_priv))
- intel_snps_phy_ddi_vswing_sequence(encoder, level);
- else
- tgl_ddi_vswing_sequence(encoder, crtc_state, level);
+ tgl_ddi_vswing_sequence(encoder, crtc_state, level);
/*
* 7.f Combo PHY: Configure PORT_CL_DW10 Static Power Down to power up
@@ -2708,7 +2823,9 @@ static void intel_ddi_pre_enable_dp(struct intel_atomic_state *state,
{
struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
- if (DISPLAY_VER(dev_priv) >= 12)
+ if (IS_DG2(dev_priv))
+ dg2_ddi_pre_enable_dp(state, encoder, crtc_state, conn_state);
+ else if (DISPLAY_VER(dev_priv) >= 12)
tgl_ddi_pre_enable_dp(state, encoder, crtc_state, conn_state);
else
hsw_ddi_pre_enable_dp(state, encoder, crtc_state, conn_state);
@@ -4634,6 +4751,8 @@ void intel_ddi_init(struct drm_i915_private *dev_priv, enum port port)
encoder->pipe_mask = ~0;
if (IS_DG2(dev_priv)) {
+ encoder->enable_clock = intel_mpllb_enable;
+ encoder->disable_clock = intel_mpllb_disable;
encoder->get_config = dg2_ddi_get_config;
} else if (IS_ALDERLAKE_S(dev_priv)) {
encoder->enable_clock = adls_ddi_enable_clock;
--
2.25.4
