Re: [PATCH 2/4] i2c: stm32f4: Fix stmpe811 get xyz data timeout issue

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Dillon

On 5/14/21 1:02 PM, dillon.minfei@xxxxxxxxx wrote:
> From: Dillon Min <dillon.minfei@xxxxxxxxx>
> 
> As stm32f429's internal flash is 2Mbytes and compiled kernel
> image bigger than 2Mbytes, so we have to load kernel image
> to sdram on stm32f429-disco board which has 8Mbytes sdram space.
> 
> based on above context, as you knows kernel running on external
> sdram is more slower than internal flash. besides, we need read 4
> bytes to get touch screen xyz(x, y, pressure) coordinate data in
> stmpe811 interrupt.
> 
> so, in stm32f4_i2c_handle_rx_done, as i2c read slower than running
> in xip mode, have to adjust 'STOP/START bit set position' from last
> two bytes to last one bytes. else, will get i2c timeout in reading
> touch screen coordinate.
> 
> to not bring in side effect, introduce IIC_LAST_BYTE_POS to support xip
> kernel or zImage.
> 
> Fixes: 62817fc8d282 ("i2c: stm32f4: add driver")
> Link: https://lore.kernel.org/lkml/1591709203-12106-5-git-send-email-dillon.minfei@xxxxxxxxx/
> Signed-off-by: Dillon Min <dillon.minfei@xxxxxxxxx>
> ---
>  drivers/i2c/busses/i2c-stm32f4.c | 12 +++++++++---
>  1 file changed, 9 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/i2c/busses/i2c-stm32f4.c b/drivers/i2c/busses/i2c-stm32f4.c
> index 4933fc8ce3fd..2e41231b9037 100644
> --- a/drivers/i2c/busses/i2c-stm32f4.c
> +++ b/drivers/i2c/busses/i2c-stm32f4.c
> @@ -93,6 +93,12 @@
>  #define STM32F4_I2C_MAX_FREQ		46U
>  #define HZ_TO_MHZ			1000000
>  
> +#if !defined(CONFIG_MMU) && !defined(CONFIG_XIP_KERNEL)
> +#define IIC_LAST_BYTE_POS 1
> +#else
> +#define IIC_LAST_BYTE_POS 2
> +#endif
> +
>  /**
>   * struct stm32f4_i2c_msg - client specific data
>   * @addr: 8-bit slave addr, including r/w bit
> @@ -439,7 +445,7 @@ static void stm32f4_i2c_handle_rx_done(struct stm32f4_i2c_dev *i2c_dev)
>  	int i;
>  
>  	switch (msg->count) {
> -	case 2:
> +	case IIC_LAST_BYTE_POS:
>  		/*
>  		 * In order to correctly send the Stop or Repeated Start
>  		 * condition on the I2C bus, the STOP/START bit has to be set
> @@ -454,7 +460,7 @@ static void stm32f4_i2c_handle_rx_done(struct stm32f4_i2c_dev *i2c_dev)
>  		else
>  			stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_START);
>  
> -		for (i = 2; i > 0; i--)
> +		for (i = IIC_LAST_BYTE_POS; i > 0; i--)
>  			stm32f4_i2c_read_msg(i2c_dev);
>  
>  		reg = i2c_dev->base + STM32F4_I2C_CR2;
> @@ -463,7 +469,7 @@ static void stm32f4_i2c_handle_rx_done(struct stm32f4_i2c_dev *i2c_dev)
>  
>  		complete(&i2c_dev->complete);
>  		break;
> -	case 3:
> +	case (IIC_LAST_BYTE_POS+1):
>  		/*
>  		 * In order to correctly generate the NACK pulse after the last
>  		 * received data byte, we have to enable NACK before reading N-2
> 

I tested this patch on STM32F429-Disco, it fixes the issue described by Dillon.
But i think it's not a good idea to make usage of #if !defined(CONFIG_MMU) && !defined(CONFIG_XIP_KERNEL)
inside the driver code.

Pierre-Yves, Alain, as i am not I2C expert, can you have a look at this patch and propose another solution 
to fix the original issue described by Dillon ?

Thanks
Patrice



[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux