On Mon, Mar 01, 2021 at 02:58:36PM +0530, Kiran Gunda wrote: > As per the current implementation, after FSC (Full Scale Current) > and brightness update the sync bits are transitioned from set-then-clear. This does not makes sense since there are too many verbs. Set and clear are both verbs so in this context: "the code will set the bit and then the code will clear the bit". Either: s/transitioned from set-then-clear/set-then-cleared/. Or: s/transitioned from set-then-clear/using a set-then-clear approach/. > But, the FSC and brightness sync takes place during a clear-then-set > transition of the sync bits. Likewise this no longer makes sense and had also become misleading. Two changes of state, clear and then set, do not usually result in a single transition. Either: s/clear-then-set/0 to 1/ Alternatively, if you want to stick exclusively to the set/clear terminology then replace the whole quoted section with: But, the FSC and brightness sync takes place when the sync bits are set (e.g. on a rising edge). > So the hardware team recommends a > clear-then-set approach in order to guarantee such a transition > regardless of the previous register state. > > Signed-off-by: Kiran Gunda <kgunda@xxxxxxxxxxxxxx> With one of each of the changes proposed above: Reviewed-by: Daniel Thompson <daniel.thompson@xxxxxxxxxx> Daniel. > --- > drivers/video/backlight/qcom-wled.c | 12 ++++++------ > 1 file changed, 6 insertions(+), 6 deletions(-) > > diff --git a/drivers/video/backlight/qcom-wled.c b/drivers/video/backlight/qcom-wled.c > index aef52b9..19f83ac 100644 > --- a/drivers/video/backlight/qcom-wled.c > +++ b/drivers/video/backlight/qcom-wled.c > @@ -337,13 +337,13 @@ static int wled3_sync_toggle(struct wled *wled) > > rc = regmap_update_bits(wled->regmap, > wled->ctrl_addr + WLED3_SINK_REG_SYNC, > - mask, mask); > + mask, WLED3_SINK_REG_SYNC_CLEAR); > if (rc < 0) > return rc; > > rc = regmap_update_bits(wled->regmap, > wled->ctrl_addr + WLED3_SINK_REG_SYNC, > - mask, WLED3_SINK_REG_SYNC_CLEAR); > + mask, mask); > > return rc; > } > @@ -353,17 +353,17 @@ static int wled5_mod_sync_toggle(struct wled *wled) > int rc; > u8 val; > > - val = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_SYNC_MOD_A_BIT : > - WLED5_SINK_REG_SYNC_MOD_B_BIT; > rc = regmap_update_bits(wled->regmap, > wled->sink_addr + WLED5_SINK_REG_MOD_SYNC_BIT, > - WLED5_SINK_REG_SYNC_MASK, val); > + WLED5_SINK_REG_SYNC_MASK, 0); > if (rc < 0) > return rc; > > + val = (wled->cfg.mod_sel == MOD_A) ? WLED5_SINK_REG_SYNC_MOD_A_BIT : > + WLED5_SINK_REG_SYNC_MOD_B_BIT; > return regmap_update_bits(wled->regmap, > wled->sink_addr + WLED5_SINK_REG_MOD_SYNC_BIT, > - WLED5_SINK_REG_SYNC_MASK, 0); > + WLED5_SINK_REG_SYNC_MASK, val); > } > > static int wled_ovp_fault_status(struct wled *wled, bool *fault_set) > -- > The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum, > a Linux Foundation Collaborative Project > _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
