Hi Riadh,
On Wed, Feb 17, 2021 at 8:44 PM Riadh Ghaddab <rghaddab@xxxxxxxxxxxx> wrote:
>
> Hi Jagan,
>
> On 20/01/2021 12:21, Jagan Teki wrote:
>
> SN65DSI84 is a Single Channel DSI to Dual-link LVDS bridge from
> Texas Instruments.
>
> SN65DSI83, SN65DSI85 are variants of the same family of bridge
> controllers.
>
> Right now the bridge driver is supporting a single link, dual-link
> support requires to initiate I2C Channel B registers.
>
> Tested with STM32MP1 MIPI DSI host design configuration.
>
> Do you have the code to support the Dual channel LVDS feature ?
> If not I recently developed the code for a board using sn65dsi84 with Dual
> LVDS channel
I have the basic one, but not have the proper hardware to verify
dual-link. Please have a look at V2 of similar patches. We will sort
out the driver so-that it can work with possible configurations.
>
> Signed-off-by: Matteo Lisi <matteo.lisi@xxxxxxxxxxx>
> Signed-off-by: Jagan Teki <jagan@xxxxxxxxxxxxxxxxxxxx>
> ---
> MAINTAINERS | 6 +
> drivers/gpu/drm/bridge/Kconfig | 19 +
> drivers/gpu/drm/bridge/Makefile | 1 +
> drivers/gpu/drm/bridge/ti-sn65dsi84.c | 488 ++++++++++++++++++++++++++
> 4 files changed, 514 insertions(+)
> create mode 100644 drivers/gpu/drm/bridge/ti-sn65dsi84.c
>
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 12dd1fff2a39..44750ff7640c 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -5984,6 +5984,12 @@ S: Maintained
> F: Documentation/devicetree/bindings/display/ti/
> F: drivers/gpu/drm/omapdrm/
>
> +DRM DRIVERS FOR TI SN65DSI84 DSI TO LVDS BRIDGE
> +M: Jagan Teki <jagan@xxxxxxxxxxxxxxxxxxxx>
> +S: Maintained
> +F: Documentation/devicetree/bindings/display/bridge/ti,sn65dsi84.yaml
> +F: drivers/gpu/drm/bridge/ti-sn65dsi84.c
> +
> DRM DRIVERS FOR V3D
> M: Eric Anholt <eric@xxxxxxxxxx>
> S: Supported
> diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
> index e4110d6ca7b3..6494881bffb3 100644
> --- a/drivers/gpu/drm/bridge/Kconfig
> +++ b/drivers/gpu/drm/bridge/Kconfig
> @@ -232,6 +232,25 @@ config DRM_TI_TFP410
> help
> Texas Instruments TFP410 DVI/HDMI Transmitter driver
>
> +config DRM_TI_SN65DSI84
> + tristate "TI SN65DSI84 DSI to LVDS bridge"
> + depends on OF
> + select DRM_KMS_HELPER
> + select REGMAP_I2C
> + select DRM_PANEL
> + select DRM_MIPI_DSI
> + help
> + Texas Instruments SN65DSI84 Single Channel DSI to Dual-link LVDS
> + bridge driver.
> +
> + Bridge decodes MIPI DSI 18bpp RGB666 and 240bpp RG888 packets and
> + converts the formatted video data stream to a FlatLink compatible
> + LVDS output operating at pixel clocks operating from 25 MHx to
> + 154 MHz.
> +
> + SN65DSI84 offers a Dual-Link LVDS, Single-Link LVDS interface with
> + four data lanes per link.
> +
> config DRM_TI_SN65DSI86
> tristate "TI SN65DSI86 DSI to eDP bridge"
> depends on OF
> diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
> index 86e7acc76f8d..3906052ef639 100644
> --- a/drivers/gpu/drm/bridge/Makefile
> +++ b/drivers/gpu/drm/bridge/Makefile
> @@ -20,6 +20,7 @@ obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o
> obj-$(CONFIG_DRM_TOSHIBA_TC358768) += tc358768.o
> obj-$(CONFIG_DRM_TOSHIBA_TC358775) += tc358775.o
> obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/
> +obj-$(CONFIG_DRM_TI_SN65DSI84) += ti-sn65dsi84.o
> obj-$(CONFIG_DRM_TI_SN65DSI86) += ti-sn65dsi86.o
> obj-$(CONFIG_DRM_TI_TFP410) += ti-tfp410.o
> obj-$(CONFIG_DRM_TI_TPD12S015) += ti-tpd12s015.o
> diff --git a/drivers/gpu/drm/bridge/ti-sn65dsi84.c b/drivers/gpu/drm/bridge/ti-sn65dsi84.c
> new file mode 100644
> index 000000000000..3ed1f9a7d898
> --- /dev/null
> +++ b/drivers/gpu/drm/bridge/ti-sn65dsi84.c
> @@ -0,0 +1,488 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2021 Engicam srl
> + * Copyright (C) 2021 Amarula Solutions(India)
> + * Author: Jagan Teki <jagan@xxxxxxxxxxxxxxxxxxxx>
> + */
> +
> +#include <drm/drm_of.h>
> +#include <drm/drm_panel.h>
> +#include <drm/drm_print.h>
> +#include <drm/drm_mipi_dsi.h>
> +
> +#include <linux/delay.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/regmap.h>
> +
> +/* sn65dsi84 registers */
> +#define SN65DSI_SOFT_RESET 0x09
> +#define SN65DSI_LVDS_CLK 0x0a
> +#define SN65DSI_CLK_DIV 0x0b
> +#define SN65DSI_CLK_PLL 0x0d
> +#define SN65DSI_DSI_CFG 0x10
> +#define SN65DSI_DSI_CLK_EQ 0x11
> +#define SN65DSI_DSI_CLK_RANGE 0x12
> +#define SN65DSI_LVDS_MODE 0x18
> +#define SN65DSI_CHA_LINE_LO 0x20
> +#define SN65DSI_CHA_LINE_HI 0x21
> +#define SN65DSI_CHA_VIRT_LO 0x24
> +#define SN65DSI_CHA_VIRT_HI 0x25
> +#define SN65DSI_CHA_SYNC_DELAY_LO 0x28
> +#define SN65DSI_CHA_SYNC_DELAY_HI 0x29
> +#define SN65DSI_CHA_HSYNC_WIDTH_LO 0x2c
> +#define SN65DSI_CHA_HSYNC_WIDTH_HI 0x2d
> +#define SN65DSI_CHA_VSYNC_WIDTH_LO 0x30
> +#define SN65DSI_CHA_VSYNC_WIDTH_HI 0x31
> +#define SN65DSI_CHA_HBACK_PORCH 0x34
> +#define SN65DSI_CHA_VBACK_PORCH 0x36
> +#define SN65DSI_CHA_HFRONT_PORCH 0x38
> +#define SN65DSI_CHA_VFRONT_PORCH 0x3a
> +#define SN65DSI_CHA_ERR 0xe5
> +
> +/* sn65dsi register bits */
> +#define SN65DSI_RESET_EN BIT(0)
> +#define SN65DSI_PLL_EN BIT(0)
> +#define SN65DSI_LVDS_CLK_MASK GENMASK(3, 1)
> +#define SN65DSI_LVDS_CLK_SHIFT 1
> +#define SN65DSI_LVDS_CLK_SRC_DSI BIT(0)
> +#define SN65DSI_CLK_DIV_MASK GENMASK(7, 3)
> +#define SN65DSI_CLK_DIV_SHIFT 3
> +#define SN65DSI_DSI_LANE_MASK GENMASK(4, 3)
> +#define SN65DSI_DSI_LANE_SHIFT 3
> +#define SN65DSI_LVDS_LINK_CFG BIT(4)
> +#define SN65DSI_LVDS_CHA_24BPP BIT(3)
> +#define SN65DSI_CHA_LOW_SYNC_DELAY 0x20
> +#define SN65DSI_CHA_HIGH_SYNC_DELAY 0x00
> +
> +struct sn65dsi {
> + struct device *dev;
> + struct drm_bridge bridge;
> + struct drm_bridge *panel_bridge;
> +
> + struct device_node *host_node;
> + struct mipi_dsi_device *dsi;
> + u8 dsi_lanes;
> +
> + struct regmap *regmap;
> + struct gpio_desc *enable;
> +};
> +
> +static const struct regmap_config sn65dsi_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .max_register = SN65DSI_CHA_ERR,
> + .name = "sn65dsi",
> + .cache_type = REGCACHE_RBTREE,
> +};
> +
> +static inline struct sn65dsi *bridge_to_sn65dsi(struct drm_bridge *bridge)
> +{
> + return container_of(bridge, struct sn65dsi, bridge);
> +}
> +
> +static struct drm_display_mode *bridge_to_mode(struct drm_bridge *bridge)
> +{
> + return &bridge->encoder->crtc->state->mode;
> +}
> +
> +static void sn65dsi_setup_channels(struct sn65dsi *sn,
> + struct drm_display_mode *mode)
> +{
> + u32 hsync_len, hfront_porch, hback_porch;
> + u32 vsync_len, vfront_porch, vback_porch;
> +
> + hfront_porch = mode->hsync_start - mode->hdisplay;
> + hsync_len = mode->hsync_end - mode->hsync_start;
> + hback_porch = mode->htotal - mode->hsync_end;
> +
> + vfront_porch = mode->vsync_start - mode->vdisplay;
> + vsync_len = mode->vsync_end - mode->vsync_start;
> + vback_porch = mode->vtotal - mode->vsync_end;
> +
> + /* cha, lower 8-bits of hdisplay */
> + regmap_write(sn->regmap, SN65DSI_CHA_LINE_LO, mode->hdisplay & 0xff);
> +
> + msleep(10);
> +
> + /* cha, upper 4-bits of hdisplay */
> + regmap_write(sn->regmap, SN65DSI_CHA_LINE_HI, (mode->hdisplay >> 8) & 0xff);
> +
> + msleep(10);
> +
> + /* cha, lower 8-bits of vdisplay */
> + regmap_write(sn->regmap, SN65DSI_CHA_VIRT_LO, mode->vdisplay & 0xff);
> +
> + msleep(10);
> +
> + /* cha, upper 4-bits of vdisplay */
> + regmap_write(sn->regmap, SN65DSI_CHA_VIRT_HI, (mode->vdisplay >> 8) & 0xff);
> +
> + msleep(10);
> +
>
> According to the datasheet, the Vertical active parameter are not needed. They are used only for
> test pattern generation.
I will check this.
>
> + /*cha, lower sync delay */
> + regmap_write(sn->regmap, SN65DSI_CHA_SYNC_DELAY_LO, SN65DSI_CHA_LOW_SYNC_DELAY);
> +
> + msleep(10);
> +
> + /*cha, upper sync delay */
> + regmap_write(sn->regmap, SN65DSI_CHA_SYNC_DELAY_HI, SN65DSI_CHA_HIGH_SYNC_DELAY);
> +
> + msleep(10);
> +
> + /* cha, lower 8-bits of hsync_len */
> + regmap_write(sn->regmap, SN65DSI_CHA_HSYNC_WIDTH_LO, hsync_len & 0xff);
> +
> + msleep(10);
> +
> + /* cha, upper 2-bits of hsync_len */
> + regmap_write(sn->regmap, SN65DSI_CHA_HSYNC_WIDTH_HI, (hsync_len >> 8) & 0xff);
> +
> + msleep(10);
> +
> + /* cha, lower 8-bits of vsync_len */
> + regmap_write(sn->regmap, SN65DSI_CHA_VSYNC_WIDTH_LO, vsync_len & 0xff);
> +
> + msleep(10);
> +
> + /* cha, upper 2-bits of vsync_len */
> + regmap_write(sn->regmap, SN65DSI_CHA_VSYNC_WIDTH_HI, (vsync_len >> 8) & 0xff);
> +
> + msleep(10);
> +
> + /* cha, hback_porch */
> + regmap_write(sn->regmap, SN65DSI_CHA_HBACK_PORCH, hback_porch & 0xff);
> +
> + msleep(10);
> +
> + /* cha, vback_porch */
> + regmap_write(sn->regmap, SN65DSI_CHA_VBACK_PORCH, vback_porch & 0xff);
> +
> + msleep(10);
> +
> + /* cha, hfront_porch */
> + regmap_write(sn->regmap, SN65DSI_CHA_HFRONT_PORCH, hfront_porch & 0xff);
> +
> + msleep(10);
> +
> + /* cha, vfront_porch */
> + regmap_write(sn->regmap, SN65DSI_CHA_VFRONT_PORCH, vfront_porch & 0xff);
> +
> + msleep(10);
> +}
> +
> +static int sn65dsi_get_clk_range(int min, int max, unsigned long clock,
> + unsigned long start, unsigned long diff)
> +{
> + unsigned long next;
> + int i;
> +
> + for (i = min; i <= max; i++) {
> + next = start + diff;
> + if (start <= clock && clock < next)
> + return i;
> +
> + start += diff;
> + }
> +
> + return -EINVAL;
> +}
> +
> +static void sn65dsi_enable(struct drm_bridge *bridge)
> +{
> + struct sn65dsi *sn = bridge_to_sn65dsi(bridge);
> + struct drm_display_mode *mode = bridge_to_mode(bridge);
> + int bpp = mipi_dsi_pixel_format_to_bpp(sn->dsi->format);
> + unsigned int lanes = sn->dsi->lanes;
> + unsigned int pixel_clk = mode->clock * 1000;
> + unsigned int dsi_clk = pixel_clk * bpp / (lanes * 2);
> + unsigned int val;
> +
> + /* set SOFT_RESET bit */
> + regmap_write(sn->regmap, SN65DSI_SOFT_RESET, SN65DSI_RESET_EN);
> +
> + msleep(10);
> +
> + /* set PLL_EN bit */
> + regmap_write(sn->regmap, SN65DSI_CLK_PLL, 0x0);
> +
> + msleep(10);
> +
> + /* setup lvds clock */
> + val = sn65dsi_get_clk_range(0, 5, pixel_clk, 25000000, 25000000);
> + if (val < 0) {
> + DRM_DEV_ERROR(sn->dev, "invalid LVDS clock range %d\n", val);
> + return;
> + }
> +
> + regmap_update_bits(sn->regmap, SN65DSI_LVDS_CLK,
> + SN65DSI_LVDS_CLK_MASK,
> + val << SN65DSI_LVDS_CLK_SHIFT);
> +
> + regmap_update_bits(sn->regmap, SN65DSI_LVDS_CLK,
> + SN65DSI_LVDS_CLK_SRC_DSI,
> + SN65DSI_LVDS_CLK_SRC_DSI);
> +
> + msleep(10);
> +
> + /* setup bridge clock divider */
> + val = (dsi_clk / pixel_clk) - 1;
> + regmap_update_bits(sn->regmap, SN65DSI_CLK_DIV,
> + SN65DSI_CLK_DIV_MASK,
> + val << SN65DSI_CLK_DIV_SHIFT);
> + msleep(10);
> +
> + /* configure dsi */
> + regmap_update_bits(sn->regmap, SN65DSI_DSI_CFG,
> + SN65DSI_DSI_LANE_MASK,
> + lanes << SN65DSI_DSI_LANE_SHIFT);
> + msleep(10);
> +
> + /* dsi clock range */
> + val = sn65dsi_get_clk_range(8, 100, dsi_clk, 40000000, 5000000);
> + if (val < 0) {
> + DRM_DEV_ERROR(sn->dev, "invalid DSI clock range %d\n", val);
> + return;
> + }
> +
> + regmap_write(sn->regmap, SN65DSI_DSI_CLK_RANGE, val);
> +
> + msleep(10);
> +
> + /* setup lvds channels */
> + regmap_read(sn->regmap, SN65DSI_LVDS_MODE, &val);
> + if (bpp == 24)
> + val |= SN65DSI_LVDS_CHA_24BPP;
> + regmap_write(sn->regmap, SN65DSI_LVDS_MODE, val);
> +
> + msleep(10);
> +
> + /* TODO Channel B required to set up for dual-link LVDS */
> + sn65dsi_setup_channels(sn, mode);
> +
> + /* set PLL_EN bit */
> + regmap_write(sn->regmap, SN65DSI_CLK_PLL, SN65DSI_PLL_EN);
> +
> + msleep(10);
> +}
>
> According to the initialization sequence from TI, setting up the channel parameters
> and the PLL clock should be done while the DSI clk are in HS mode and the DSI data
> lanes are in LP11 mode.
> Shouldn't this be done in the pre-enable function ?
I believe it doesn't matter as drm_atomic would pre_enable and enable
in sequence. I have categories pre_enable for GPIO and the rest of
bridge initialization for enable code. Did you see any issues with
this setup, which DSI host are you using for it?
Jagan.
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
