On Wed, 2021-02-10 at 23:15 -0500, Rodrigo Vivi wrote:
> On Mon, Feb 08, 2021 at 06:39:00PM -0500, Lyude Paul wrote:
> > Since we're about to implement eDP backlight support in nouveau using the
> > standard protocol from VESA, we might as well just take the code that's
> > already written for this and move it into a set of shared DRM helpers.
> >
> > Note that these helpers are intended to handle DPCD related backlight
> > control bits such as setting the brightness level over AUX, probing the
> > backlight's TCON, enabling/disabling the backlight over AUX if supported,
> > etc. Any PWM-related portions of backlight control are explicitly left up
> > to the driver, as these will vary from platform to platform.
> >
> > The only exception to this is the calculation of the PWM frequency
> > pre-divider value. This is because the only platform-specific information
> > required for this is the PWM frequency of the panel, which the driver is
> > expected to provide if available. The actual algorithm for calculating this
> > value is standard and is defined in the eDP specification from VESA.
> >
> > Note that these helpers do not yet implement the full range of features
> > the VESA backlight interface provides, and only provide the following
> > functionality (all of which was already present in i915's DPCD backlight
> > support):
> >
> > * Basic control of brightness levels
> > * Basic probing of backlight capabilities
> > * Helpers for enabling and disabling the backlight
> >
> > v3:
> > * Split out changes to i915's backlight code to separate patches to make it
> > easier to review
> > v4:
> > * Style/spelling changes from Thomas Zimmermann
> >
> > Signed-off-by: Lyude Paul <lyude@xxxxxxxxxx>
> > Cc: Jani Nikula <jani.nikula@xxxxxxxxx>
> > Cc: Dave Airlie <airlied@xxxxxxxxx>
> > Cc: greg.depoire@xxxxxxxxx
> > ---
> > drivers/gpu/drm/drm_dp_helper.c | 332 ++++++++++++++++++
> > .../drm/i915/display/intel_display_types.h | 5 +-
> > .../drm/i915/display/intel_dp_aux_backlight.c | 285 ++-------------
> > include/drm/drm_dp_helper.h | 48 +++
> > 4 files changed, 412 insertions(+), 258 deletions(-)
> >
> > diff --git a/drivers/gpu/drm/drm_dp_helper.c
> > b/drivers/gpu/drm/drm_dp_helper.c
> > index eedbb48815b7..1a3d4679d720 100644
> > --- a/drivers/gpu/drm/drm_dp_helper.c
> > +++ b/drivers/gpu/drm/drm_dp_helper.c
> > @@ -3082,3 +3082,335 @@ int drm_dp_pcon_convert_rgb_to_ycbcr(struct
> > drm_dp_aux *aux, u8 color_spc)
> > return 0;
> > }
> > EXPORT_SYMBOL(drm_dp_pcon_convert_rgb_to_ycbcr);
> > +
> > +/**
> > + * drm_edp_backlight_set_level() - Set the backlight level of an eDP panel
> > via AUX
> > + * @aux: The DP AUX channel to use
> > + * @bl: Backlight capability info from drm_edp_backlight_init()
> > + * @level: The brightness level to set
> > + *
> > + * Sets the brightness level of an eDP panel's backlight. Note that the
> > panel's backlight must
> > + * already have been enabled by the driver by calling
> > drm_edp_backlight_enable().
> > + *
> > + * Returns: %0 on success, negative error code on failure
> > + */
> > +int drm_edp_backlight_set_level(struct drm_dp_aux *aux, const struct
> > drm_edp_backlight_info *bl,
> > + u16 level)
> > +{
> > + int ret;
> > + u8 buf[2] = { 0 };
> > +
> > + if (bl->lsb_reg_used) {
> > + buf[0] = (level & 0xff00) >> 8;
> > + buf[1] = (level & 0x00ff);
> > + } else {
> > + buf[0] = level;
> > + }
> > +
> > + ret = drm_dp_dpcd_write(aux, DP_EDP_BACKLIGHT_BRIGHTNESS_MSB, buf,
> > sizeof(buf));
> > + if (ret != sizeof(buf)) {
> > + DRM_ERROR("%s: Failed to write aux backlight level: %d\n",
> > aux->name, ret);
> > + return ret < 0 ? ret : -EIO;
> > + }
> > +
> > + return 0;
> > +}
> > +EXPORT_SYMBOL(drm_edp_backlight_set_level);
> > +
> > +static int
> > +drm_edp_backlight_set_enable(struct drm_dp_aux *aux, const struct
> > drm_edp_backlight_info *bl,
> > + bool enable)
> > +{
> > + int ret;
> > + u8 buf;
> > +
> > + /* The panel uses something other then DPCD for enabling its
> > backlight */
> > + if (!bl->aux_enable)
> > + return 0;
> > +
> > + ret = drm_dp_dpcd_readb(aux, DP_EDP_DISPLAY_CONTROL_REGISTER, &buf);
> > + if (ret != 1) {
> > + DRM_ERROR("%s: Failed to read eDP display control register:
> > %d\n", aux->name, ret);
> > + return ret < 0 ? ret : -EIO;
> > + }
> > + if (enable)
> > + buf |= DP_EDP_BACKLIGHT_ENABLE;
> > + else
> > + buf &= ~DP_EDP_BACKLIGHT_ENABLE;
> > +
> > + ret = drm_dp_dpcd_writeb(aux, DP_EDP_DISPLAY_CONTROL_REGISTER, buf);
> > + if (ret != 1) {
> > + DRM_ERROR("%s: Failed to write eDP display control register:
> > %d\n", aux->name, ret);
> > + return ret < 0 ? ret : -EIO;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +/**
> > + * drm_edp_backlight_enable() - Enable an eDP panel's backlight using DPCD
> > + * @aux: The DP AUX channel to use
> > + * @bl: Backlight capability info from drm_edp_backlight_init()
> > + * @level: The initial backlight level to set via AUX, if there is one
> > + *
> > + * This function handles enabling DPCD backlight controls on a panel over
> > DPCD, while additionally
> > + * restoring any important backlight state such as the given backlight
> > level, the brightness byte
> > + * count, backlight frequency, etc.
> > + *
> > + * Note that certain panels, while supporting brightness level controls
> > over DPCD, may not support
> > + * having their backlights enabled via the standard
> > %DP_EDP_DISPLAY_CONTROL_REGISTER. On such panels
> > + * &drm_edp_backlight_info.aux_enable will be set to %false, this function
> > will skip the step of
> > + * programming the %DP_EDP_DISPLAY_CONTROL_REGISTER, and the driver must
> > perform the required
> > + * implementation specific step for enabling the backlight after calling
> > this function.
> > + *
> > + * Returns: %0 on success, negative error code on failure.
> > + */
> > +int drm_edp_backlight_enable(struct drm_dp_aux *aux, const struct
> > drm_edp_backlight_info *bl,
> > + const u16 level)
> > +{
> > + int ret;
> > + u8 dpcd_buf, new_dpcd_buf;
> > +
> > + ret = drm_dp_dpcd_readb(aux, DP_EDP_BACKLIGHT_MODE_SET_REGISTER,
> > &dpcd_buf);
> > + if (ret != 1) {
> > + DRM_DEBUG_KMS("%s: Failed to read backlight mode: %d\n",
> > aux->name, ret);
> > + return ret < 0 ? ret : -EIO;
> > + }
> > +
> > + new_dpcd_buf = dpcd_buf;
> > +
> > + if ((dpcd_buf & DP_EDP_BACKLIGHT_CONTROL_MODE_MASK) !=
> > DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD) {
> > + new_dpcd_buf &= ~DP_EDP_BACKLIGHT_CONTROL_MODE_MASK;
> > + new_dpcd_buf |= DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD;
> > +
> > + ret = drm_dp_dpcd_writeb(aux, DP_EDP_PWMGEN_BIT_COUNT, bl-
> > >pwmgen_bit_count);
> > + if (ret != 1)
> > + DRM_DEBUG_KMS("%s: Failed to write aux pwmgen bit
> > count: %d\n",
> > + aux->name, ret);
> > + }
> > +
> > + if (bl->pwm_freq_pre_divider) {
> > + ret = drm_dp_dpcd_writeb(aux, DP_EDP_BACKLIGHT_FREQ_SET, bl-
> > >pwm_freq_pre_divider);
> > + if (ret != 1)
> > + DRM_DEBUG_KMS("%s: Failed to write aux backlight
> > frequency: %d\n",
> > + aux->name, ret);
> > + else
> > + new_dpcd_buf |=
> > DP_EDP_BACKLIGHT_FREQ_AUX_SET_ENABLE;
> > + }
> > +
> > + if (new_dpcd_buf != dpcd_buf) {
> > + ret = drm_dp_dpcd_writeb(aux,
> > DP_EDP_BACKLIGHT_MODE_SET_REGISTER, new_dpcd_buf);
> > + if (ret != 1) {
> > + DRM_DEBUG_KMS("%s: Failed to write aux backlight
> > mode: %d\n",
> > + aux->name, ret);
> > + return ret < 0 ? ret : -EIO;
> > + }
> > + }
> > +
> > + ret = drm_edp_backlight_set_level(aux, bl, level);
> > + if (ret < 0)
> > + return ret;
> > + ret = drm_edp_backlight_set_enable(aux, bl, true);
> > + if (ret < 0)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +EXPORT_SYMBOL(drm_edp_backlight_enable);
> > +
> > +/**
> > + * drm_edp_backlight_disable() - Disable an eDP backlight using DPCD, if
> > supported
> > + * @aux: The DP AUX channel to use
> > + * @bl: Backlight capability info from drm_edp_backlight_init()
> > + *
> > + * This function handles disabling DPCD backlight controls on a panel over
> > AUX. Note that some
> > + * panels have backlights that are enabled/disabled by other means, despite
> > having their brightness
> > + * values controlled through DPCD. On such panels
> > &drm_edp_backlight_info.aux_enable will be set to
> > + * %false, this function will become a no-op (and we will skip updating
> > + * %DP_EDP_DISPLAY_CONTROL_REGISTER), and the driver must take care to
> > perform it's own
> > + * implementation specific step for disabling the backlight.
> > + *
> > + * Returns: %0 on success or no-op, negative error code on failure.
> > + */
> > +int drm_edp_backlight_disable(struct drm_dp_aux *aux, const struct
> > drm_edp_backlight_info *bl)
> > +{
> > + int ret;
> > +
> > + ret = drm_edp_backlight_set_enable(aux, bl, false);
> > + if (ret < 0)
> > + return ret;
> > +
> > + return 0;
> > +}
> > +EXPORT_SYMBOL(drm_edp_backlight_disable);
> > +
> > +static inline int
> > +drm_edp_backlight_probe_max(struct drm_dp_aux *aux, struct
> > drm_edp_backlight_info *bl,
> > + u16 driver_pwm_freq_hz, const u8
> > edp_dpcd[EDP_DISPLAY_CTL_CAP_SIZE])
> > +{
> > + int fxp, fxp_min, fxp_max, fxp_actual, f = 1;
> > + int ret;
> > + u8 pn, pn_min, pn_max;
> > +
> > + ret = drm_dp_dpcd_readb(aux, DP_EDP_PWMGEN_BIT_COUNT, &pn);
> > + if (ret != 1) {
> > + DRM_DEBUG_KMS("%s: Failed to read pwmgen bit count cap:
> > %d\n", aux->name, ret);
> > + return -ENODEV;
> > + }
> > +
> > + pn &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
> > + bl->max = (1 << pn) - 1;
> > + if (!driver_pwm_freq_hz)
> > + return 0;
> > +
> > + /*
> > + * Set PWM Frequency divider to match desired frequency provided by
> > the driver.
> > + * The PWM Frequency is calculated as 27Mhz / (F x P).
> > + * - Where F = PWM Frequency Pre-Divider value programmed by field
> > 7:0 of the
> > + * EDP_BACKLIGHT_FREQ_SET register (DPCD Address 00728h)
> > + * - Where P = 2^Pn, where Pn is the value programmed by field 4:0
> > of the
> > + * EDP_PWMGEN_BIT_COUNT register (DPCD Address 00724h)
> > + */
> > +
> > + /* Find desired value of (F x P)
> > + * Note that, if F x P is out of supported range, the maximum value
> > or minimum value will
> > + * applied automatically. So no need to check that.
> > + */
> > + fxp = DIV_ROUND_CLOSEST(1000 * DP_EDP_BACKLIGHT_FREQ_BASE_KHZ,
> > driver_pwm_freq_hz);
> > +
> > + /* Use highest possible value of Pn for more granularity of
> > brightness adjustment while
> > + * satifying the conditions below.
> > + * - Pn is in the range of Pn_min and Pn_max
> > + * - F is in the range of 1 and 255
> > + * - FxP is within 25% of desired value.
> > + * Note: 25% is arbitrary value and may need some tweak.
> > + */
> > + ret = drm_dp_dpcd_readb(aux, DP_EDP_PWMGEN_BIT_COUNT_CAP_MIN,
> > &pn_min);
> > + if (ret != 1) {
> > + DRM_DEBUG_KMS("%s: Failed to read pwmgen bit count cap min:
> > %d\n", aux->name, ret);
> > + return 0;
> > + }
> > + ret = drm_dp_dpcd_readb(aux, DP_EDP_PWMGEN_BIT_COUNT_CAP_MAX,
> > &pn_max);
> > + if (ret != 1) {
> > + DRM_DEBUG_KMS("%s: Failed to read pwmgen bit count cap max:
> > %d\n", aux->name, ret);
> > + return 0;
> > + }
> > + pn_min &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
> > + pn_max &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
> > +
> > + /* Ensure frequency is within 25% of desired value */
> > + fxp_min = DIV_ROUND_CLOSEST(fxp * 3, 4);
> > + fxp_max = DIV_ROUND_CLOSEST(fxp * 5, 4);
> > + if (fxp_min < (1 << pn_min) || (255 << pn_max) < fxp_max) {
> > + DRM_DEBUG_KMS("%s: Driver defined backlight frequency (%d)
> > out of range\n",
> > + aux->name, driver_pwm_freq_hz);
> > + return 0;
> > + }
> > +
> > + for (pn = pn_max; pn >= pn_min; pn--) {
> > + f = clamp(DIV_ROUND_CLOSEST(fxp, 1 << pn), 1, 255);
> > + fxp_actual = f << pn;
> > + if (fxp_min <= fxp_actual && fxp_actual <= fxp_max)
> > + break;
> > + }
> > +
> > + ret = drm_dp_dpcd_writeb(aux, DP_EDP_PWMGEN_BIT_COUNT, pn);
> > + if (ret != 1) {
> > + DRM_DEBUG_KMS("%s: Failed to write aux pwmgen bit count:
> > %d\n", aux->name, ret);
> > + return 0;
> > + }
> > + bl->pwmgen_bit_count = pn;
> > + bl->max = (1 << pn) - 1;
> > +
> > + if (edp_dpcd[2] & DP_EDP_BACKLIGHT_FREQ_AUX_SET_CAP) {
> > + bl->pwm_freq_pre_divider = f;
> > + DRM_DEBUG_KMS("%s: Using backlight frequency from driver
> > (%dHz)\n",
> > + aux->name, driver_pwm_freq_hz);
> > + }
> > +
> > + return 0;
> > +}
> > +
>
> thanks for the clean up...
> up to this point it was easy to see the code added and code remove matches...
>
> > +static inline int
> > +drm_edp_backlight_probe_level(struct drm_dp_aux *aux, struct
> > drm_edp_backlight_info *bl,
> > + u8 *current_mode)
> > +{
> > + int ret;
> > + u8 buf[2];
> > + u8 mode_reg;
> > +
> > + ret = drm_dp_dpcd_readb(aux, DP_EDP_BACKLIGHT_MODE_SET_REGISTER,
> > &mode_reg);
> > + if (ret != 1) {
> > + DRM_DEBUG_KMS("%s: Failed to read backlight mode: %d\n",
> > aux->name, ret);
> > + return ret < 0 ? ret : -EIO;
> > + }
> > +
> > + *current_mode = (mode_reg & DP_EDP_BACKLIGHT_CONTROL_MODE_MASK);
> > + if (*current_mode == DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD) {
>
> However I'm afraid that on this area here we have something that could be
> improved further...
>
> > + int size = 1 + bl->lsb_reg_used;
> > +
> > + ret = drm_dp_dpcd_read(aux, DP_EDP_BACKLIGHT_BRIGHTNESS_MSB,
> > buf, size);
> > + if (ret != size) {
> > + DRM_DEBUG_KMS("%s: Failed to read backlight level:
> > %d\n", aux->name, ret);
>
> But probably the biggest blocker is the "regression" of the debug logs.
> Not just in this point, but I mean everywhere...
> the use of the old DRM_DEBUG_KMS should be avoided here imho.
> Although it is backlight, what it would mean integrated and only
> one device available, this will at least change how we see the logs..
>
> Any change of using drm_dbg_*(drm, ?!
It'll take a tree-wide patch series, but I'll go ahead and do that
today/tomorrow :)
>
> > + return ret < 0 ? ret : -EIO;
> > + }
> > +
> > + if (bl->lsb_reg_used)
> > + return (buf[0] << 8) | buf[1];
> > + else
> > + return buf[0];
> > + }
> > +
> > + /*
> > + * If we're not in DPCD control mode yet, the programmed brightness
> > value is meaningless and
> > + * the driver should assume max brightness
> > + */
> > + return bl->max;
> > +}
> > +
> > +/**
> > + * drm_edp_backlight_init() - Probe a display panel's TCON using the
> > standard VESA eDP backlight
> > + * interface.
> > + * @aux: The DP aux device to use for probing
> > + * @bl: The &drm_edp_backlight_info struct to fill out with information on
> > the backlight
> > + * @driver_pwm_freq_hz: Optional PWM frequency from the driver in hz
> > + * @edp_dpcd: A cached copy of the eDP DPCD
> > + * @current_level: Where to store the probed brightness level
> > + * @current_mode: Where to store the currently set backlight control mode
> > + *
> > + * Initializes a &drm_edp_backlight_info struct by probing @aux for it's
> > backlight capabilities,
> > + * along with also probing the current and maximum supported brightness
> > levels.
> > + *
> > + * If @driver_pwm_freq_hz is non-zero, this will be used as the backlight
> > frequency. Otherwise, the
> > + * default frequency from the panel is used.
> > + *
> > + * Returns: %0 on success, negative error code on failure.
> > + */
> > +int
> > +drm_edp_backlight_init(struct drm_dp_aux *aux, struct
> > drm_edp_backlight_info *bl,
> > + u16 driver_pwm_freq_hz, const u8
> > edp_dpcd[EDP_DISPLAY_CTL_CAP_SIZE],
> > + u16 *current_level, u8 *current_mode)
> > +{
> > + int ret;
> > +
> > + if (edp_dpcd[1] & DP_EDP_BACKLIGHT_AUX_ENABLE_CAP)
> > + bl->aux_enable = true;
> > + if (edp_dpcd[2] & DP_EDP_BACKLIGHT_BRIGHTNESS_BYTE_COUNT)
> > + bl->lsb_reg_used = true;
> > +
> > + ret = drm_edp_backlight_probe_max(aux, bl, driver_pwm_freq_hz,
> > edp_dpcd);
> > + if (ret < 0)
> > + return ret;
> > +
> > + ret = drm_edp_backlight_probe_level(aux, bl, current_mode);
> > + if (ret < 0)
> > + return ret;
> > + *current_level = ret;
> > +
> > + DRM_DEBUG_KMS("%s: Found backlight level=%d/%d
> > pwm_freq_pre_divider=%d mode=%x\n",
> > + aux->name, *current_level, bl->max, bl-
> > >pwm_freq_pre_divider, *current_mode);
> > + DRM_DEBUG_KMS("%s: Backlight caps: pwmgen_bit_count=%d
> > lsb_reg_used=%d aux_enable=%d\n",
> > + aux->name, bl->pwmgen_bit_count, bl->lsb_reg_used, bl-
> > >aux_enable);
> > + return 0;
> > +}
> > +EXPORT_SYMBOL(drm_edp_backlight_init);
> > diff --git a/drivers/gpu/drm/i915/display/intel_display_types.h
> > b/drivers/gpu/drm/i915/display/intel_display_types.h
> > index 1d8984077e8a..9f43d0b14e11 100644
> > --- a/drivers/gpu/drm/i915/display/intel_display_types.h
> > +++ b/drivers/gpu/drm/i915/display/intel_display_types.h
> > @@ -264,10 +264,7 @@ struct intel_panel {
> > /* DPCD backlight */
> > union {
> > struct {
> > - u8 pwmgen_bit_count;
> > - u8 pwm_freq_pre_divider;
> > - bool lsb_reg_used;
> > - bool aux_enable;
> > + struct drm_edp_backlight_info info;
> > } vesa;
> > struct {
> > bool sdr_uses_aux;
> > diff --git a/drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c
> > b/drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c
> > index a98d9bd4b0ed..286eb337448e 100644
> > --- a/drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c
> > +++ b/drivers/gpu/drm/i915/display/intel_dp_aux_backlight.c
> > @@ -270,114 +270,19 @@ intel_dp_aux_hdr_setup_backlight(struct
> > intel_connector *connector, enum pipe pi
> > }
> >
> > /* VESA backlight callbacks */
> > -static bool intel_dp_aux_vesa_backlight_dpcd_mode(struct intel_connector
> > *connector)
> > -{
> > - struct intel_dp *intel_dp = intel_attached_dp(connector);
> > - struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> > - int ret;
> > - u8 mode_reg;
> > -
> > - ret = drm_dp_dpcd_readb(&intel_dp->aux,
> > DP_EDP_BACKLIGHT_MODE_SET_REGISTER, &mode_reg);
> > - if (ret != 1) {
> > - drm_dbg_kms(&i915->drm, "Failed to read backlight mode:
> > %d\n", ret);
> > - return false;
> > - }
> > -
> > - return (mode_reg & DP_EDP_BACKLIGHT_CONTROL_MODE_MASK) ==
> > - DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD;
> > -}
> > -
> > -/*
> > - * Read the current backlight value from DPCD register(s) based
> > - * on if 8-bit(MSB) or 16-bit(MSB and LSB) values are supported
> > - */
> > static u32 intel_dp_aux_vesa_get_backlight(struct intel_connector
> > *connector, enum pipe unused)
> > {
> > - struct intel_dp *intel_dp = intel_attached_dp(connector);
> > - struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> > - int ret;
> > - u8 read_val[2] = { 0x0 };
> > - u16 level = 0;
> > -
> > - /*
> > - * If we're not in DPCD control mode yet, the programmed brightness
> > - * value is meaningless and we should assume max brightness
> > - */
> > - if (!intel_dp_aux_vesa_backlight_dpcd_mode(connector))
> > - return connector->panel.backlight.max;
> > -
> > - ret = drm_dp_dpcd_read(&intel_dp->aux,
> > DP_EDP_BACKLIGHT_BRIGHTNESS_MSB, &read_val,
> > - sizeof(read_val));
> > - if (ret != sizeof(read_val)) {
> > - drm_dbg_kms(&i915->drm, "Failed to read brightness level:
> > %d\n", ret);
> > - return 0;
> > - }
> > -
> > - if (connector->panel.backlight.edp.vesa.lsb_reg_used)
> > - level = (read_val[0] << 8 | read_val[1]);
> > - else
> > - level = read_val[0];
> > -
> > - return level;
> > + return connector->panel.backlight.level;
> > }
> >
> > -/*
> > - * Sends the current backlight level over the aux channel, checking if its
> > using
> > - * 8-bit or 16 bit value (MSB and LSB)
> > - */
> > static void
> > -intel_dp_aux_vesa_set_backlight(const struct drm_connector_state
> > *conn_state,
> > - u32 level)
> > +intel_dp_aux_vesa_set_backlight(const struct drm_connector_state
> > *conn_state, u32 level)
> > {
> > struct intel_connector *connector = to_intel_connector(conn_state-
> > >connector);
> > - struct intel_dp *intel_dp = intel_attached_dp(connector);
> > - struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> > - int ret;
> > - u8 vals[2] = { 0x0 };
> > -
> > - /* Write the MSB and/or LSB */
> > - if (connector->panel.backlight.edp.vesa.lsb_reg_used) {
> > - vals[0] = (level & 0xFF00) >> 8;
> > - vals[1] = (level & 0xFF);
> > - } else {
> > - vals[0] = level;
> > - }
> > -
> > - ret = drm_dp_dpcd_write(&intel_dp->aux,
> > DP_EDP_BACKLIGHT_BRIGHTNESS_MSB, vals,
> > - sizeof(vals));
> > - if (ret != sizeof(vals)) {
> > - drm_dbg_kms(&i915->drm, "Failed to write aux backlight
> > level: %d\n", ret);
> > - return;
> > - }
> > -}
> > -
> > -static void set_vesa_backlight_enable(struct intel_connector *connector,
> > bool enable)
> > -{
> > - struct intel_dp *intel_dp = intel_attached_dp(connector);
> > - struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> > - int ret;
> > - u8 reg_val = 0;
> > -
> > - /* Early return when display use other mechanism to enable
> > backlight. */
> > - if (!connector->panel.backlight.edp.vesa.aux_enable)
> > - return;
> > -
> > - ret = drm_dp_dpcd_readb(&intel_dp->aux,
> > DP_EDP_DISPLAY_CONTROL_REGISTER, ®_val);
> > - if (ret != 1) {
> > - drm_dbg_kms(&i915->drm, "Failed to read eDP display control
> > register: %d\n", ret);
> > - return;
> > - }
> > -
> > - if (enable)
> > - reg_val |= DP_EDP_BACKLIGHT_ENABLE;
> > - else
> > - reg_val &= ~(DP_EDP_BACKLIGHT_ENABLE);
> > + struct intel_panel *panel = &connector->panel;
> > + struct intel_dp *intel_dp = enc_to_intel_dp(connector->encoder);
> >
> > - ret = drm_dp_dpcd_writeb(&intel_dp->aux,
> > DP_EDP_DISPLAY_CONTROL_REGISTER, reg_val);
> > - if (ret != 1) {
> > - drm_dbg_kms(&i915->drm, "Failed to %s aux backlight: %d\n",
> > - enable ? "enable" : "disable", ret);
> > - }
> > + drm_edp_backlight_set_level(&intel_dp->aux, &panel-
> > >backlight.edp.vesa.info, level);
> > }
> >
> > static void
> > @@ -385,170 +290,46 @@ intel_dp_aux_vesa_enable_backlight(const struct
> > intel_crtc_state *crtc_state,
> > const struct drm_connector_state
> > *conn_state, u32 level)
> > {
> > struct intel_connector *connector = to_intel_connector(conn_state-
> > >connector);
> > - struct intel_dp *intel_dp = intel_attached_dp(connector);
> > - struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> > struct intel_panel *panel = &connector->panel;
> > - int ret;
> > - u8 dpcd_buf, new_dpcd_buf;
> > - u8 pwmgen_bit_count = panel->backlight.edp.vesa.pwmgen_bit_count;
> > -
> > - ret = drm_dp_dpcd_readb(&intel_dp->aux,
> > DP_EDP_BACKLIGHT_MODE_SET_REGISTER, &dpcd_buf);
> > - if (ret != 1) {
> > - drm_dbg_kms(&i915->drm, "Failed to read backlight mode:
> > %d\n", ret);
> > - return;
> > - }
> > -
> > - new_dpcd_buf = dpcd_buf;
> > -
> > - if ((dpcd_buf & DP_EDP_BACKLIGHT_CONTROL_MODE_MASK) !=
> > DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD) {
> > - new_dpcd_buf &= ~DP_EDP_BACKLIGHT_CONTROL_MODE_MASK;
> > - new_dpcd_buf |= DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD;
> > -
> > - ret = drm_dp_dpcd_writeb(&intel_dp->aux,
> > DP_EDP_PWMGEN_BIT_COUNT, pwmgen_bit_count);
> > - if (ret != 1)
> > - drm_dbg_kms(&i915->drm, "Failed to write aux pwmgen
> > bit count: %d\n", ret);
> > - }
> > -
> > - if (panel->backlight.edp.vesa.pwm_freq_pre_divider) {
> > - ret = drm_dp_dpcd_writeb(&intel_dp->aux,
> > DP_EDP_BACKLIGHT_FREQ_SET,
> > - panel-
> > >backlight.edp.vesa.pwm_freq_pre_divider);
> > - if (ret == 1)
> > - new_dpcd_buf |=
> > DP_EDP_BACKLIGHT_FREQ_AUX_SET_ENABLE;
> > - else
> > - drm_dbg_kms(&i915->drm, "Failed to write aux
> > backlight frequency: %d\n",
> > - ret);
> > - }
> > -
> > - if (new_dpcd_buf != dpcd_buf) {
> > - ret = drm_dp_dpcd_writeb(&intel_dp->aux,
> > DP_EDP_BACKLIGHT_MODE_SET_REGISTER,
> > - new_dpcd_buf);
> > - if (ret != 1)
> > - drm_dbg_kms(&i915->drm, "Failed to write aux
> > backlight mode: %d\n", ret);
> > - }
> > + struct intel_dp *intel_dp = enc_to_intel_dp(connector->encoder);
> >
> > - intel_dp_aux_vesa_set_backlight(conn_state, level);
> > - set_vesa_backlight_enable(connector, true);
> > + drm_edp_backlight_enable(&intel_dp->aux, &panel-
> > >backlight.edp.vesa.info, level);
> > }
> >
> > static void intel_dp_aux_vesa_disable_backlight(const struct
> > drm_connector_state *old_conn_state,
> > u32 level)
> > {
> > - set_vesa_backlight_enable(to_intel_connector(old_conn_state-
> > >connector), false);
> > -}
> > -
> > -/*
> > - * Compute PWM frequency divider value based off the frequency provided to
> > us by the vbt.
> > - * The PWM Frequency is calculated as 27Mhz / (F x P).
> > - * - Where F = PWM Frequency Pre-Divider value programmed by field 7:0 of
> > the
> > - * EDP_BACKLIGHT_FREQ_SET register (DPCD Address 00728h)
> > - * - Where P = 2^Pn, where Pn is the value programmed by field 4:0 of the
> > - * EDP_PWMGEN_BIT_COUNT register (DPCD Address 00724h)
> > - */
> > -static u32 intel_dp_aux_vesa_calc_max_backlight(struct intel_connector
> > *connector)
> > -{
> > - struct drm_i915_private *i915 = to_i915(connector->base.dev);
> > - struct intel_dp *intel_dp = intel_attached_dp(connector);
> > + struct intel_connector *connector =
> > to_intel_connector(old_conn_state->connector);
> > struct intel_panel *panel = &connector->panel;
> > - u32 max_backlight = 0;
> > - int ret, freq, fxp, fxp_min, fxp_max, fxp_actual, f = 1;
> > - u8 pn, pn_min, pn_max;
> > -
> > - ret = drm_dp_dpcd_readb(&intel_dp->aux, DP_EDP_PWMGEN_BIT_COUNT,
> > &pn);
> > - if (ret != 1) {
> > - drm_dbg_kms(&i915->drm, "Failed to read pwmgen bit count
> > cap: %d\n", ret);
> > - return 0;
> > - }
> > -
> > - pn &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
> > - max_backlight = (1 << pn) - 1;
> > -
> > - /* Find desired value of (F x P)
> > - * Note that, if F x P is out of supported range, the maximum value
> > or
> > - * minimum value will applied automatically. So no need to check
> > that.
> > - */
> > - freq = i915->vbt.backlight.pwm_freq_hz;
> > - drm_dbg_kms(&i915->drm, "VBT defined backlight frequency %u Hz\n",
> > - freq);
> > - if (!freq) {
> > - drm_dbg_kms(&i915->drm,
> > - "Use panel default backlight frequency\n");
> > - return max_backlight;
> > - }
> > -
> > - fxp = DIV_ROUND_CLOSEST(KHz(DP_EDP_BACKLIGHT_FREQ_BASE_KHZ), freq);
> > -
> > - /* Use highest possible value of Pn for more granularity of
> > brightness
> > - * adjustment while satifying the conditions below.
> > - * - Pn is in the range of Pn_min and Pn_max
> > - * - F is in the range of 1 and 255
> > - * - FxP is within 25% of desired value.
> > - * Note: 25% is arbitrary value and may need some tweak.
> > - */
> > - ret = drm_dp_dpcd_readb(&intel_dp->aux,
> > DP_EDP_PWMGEN_BIT_COUNT_CAP_MIN, &pn_min);
> > - if (ret != 1) {
> > - drm_dbg_kms(&i915->drm, "Failed to read pwmgen bit count cap
> > min: %d\n", ret);
> > - return max_backlight;
> > - }
> > - ret = drm_dp_dpcd_readb(&intel_dp->aux,
> > DP_EDP_PWMGEN_BIT_COUNT_CAP_MAX, &pn_max);
> > - if (ret != 1) {
> > - drm_dbg_kms(&i915->drm, "Failed to read pwmgen bit count cap
> > max: %d\n", ret);
> > - return max_backlight;
> > - }
> > - pn_min &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
> > - pn_max &= DP_EDP_PWMGEN_BIT_COUNT_MASK;
> > -
> > - /* Ensure frequency is within 25% of desired value */
> > - fxp_min = DIV_ROUND_CLOSEST(fxp * 3, 4);
> > - fxp_max = DIV_ROUND_CLOSEST(fxp * 5, 4);
> > -
> > - if (fxp_min < (1 << pn_min) || (255 << pn_max) < fxp_max) {
> > - drm_dbg_kms(&i915->drm,
> > - "VBT defined backlight frequency out of
> > range\n");
> > - return max_backlight;
> > - }
> > -
> > - for (pn = pn_max; pn >= pn_min; pn--) {
> > - f = clamp(DIV_ROUND_CLOSEST(fxp, 1 << pn), 1, 255);
> > - fxp_actual = f << pn;
> > - if (fxp_min <= fxp_actual && fxp_actual <= fxp_max)
> > - break;
> > - }
> > -
> > - drm_dbg_kms(&i915->drm, "Using eDP pwmgen bit count of %d\n", pn);
> > - ret = drm_dp_dpcd_writeb(&intel_dp->aux, DP_EDP_PWMGEN_BIT_COUNT,
> > pn);
> > - if (ret != 1) {
> > - drm_dbg_kms(&i915->drm, "Failed to write aux pwmgen bit
> > count: %d\n", ret);
> > - return max_backlight;
> > - }
> > -
> > - panel->backlight.edp.vesa.pwmgen_bit_count = pn;
> > - if (intel_dp->edp_dpcd[2] & DP_EDP_BACKLIGHT_FREQ_AUX_SET_CAP)
> > - panel->backlight.edp.vesa.pwm_freq_pre_divider = f;
> > -
> > - max_backlight = (1 << pn) - 1;
> > + struct intel_dp *intel_dp = enc_to_intel_dp(connector->encoder);
> >
> > - return max_backlight;
> > + drm_edp_backlight_disable(&intel_dp->aux, &panel-
> > >backlight.edp.vesa.info);
> > }
> >
> > -static int intel_dp_aux_vesa_setup_backlight(struct intel_connector
> > *connector,
> > - enum pipe pipe)
> > +static int intel_dp_aux_vesa_setup_backlight(struct intel_connector
> > *connector, enum pipe pipe)
> > {
> > struct intel_dp *intel_dp = intel_attached_dp(connector);
> > struct intel_panel *panel = &connector->panel;
> > + struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> > + u16 current_level;
> > + u8 current_mode;
> > + int ret;
> >
> > - if (intel_dp->edp_dpcd[1] & DP_EDP_BACKLIGHT_AUX_ENABLE_CAP)
> > - panel->backlight.edp.vesa.aux_enable = true;
> > - if (intel_dp->edp_dpcd[2] & DP_EDP_BACKLIGHT_BRIGHTNESS_BYTE_COUNT)
> > - panel->backlight.edp.vesa.lsb_reg_used = true;
> > -
> > - panel->backlight.max =
> > intel_dp_aux_vesa_calc_max_backlight(connector);
> > - if (!panel->backlight.max)
> > - return -ENODEV;
> > + ret = drm_edp_backlight_init(&intel_dp->aux, &panel-
> > >backlight.edp.vesa.info,
> > + i915->vbt.backlight.pwm_freq_hz,
> > intel_dp->edp_dpcd,
> > + ¤t_level, ¤t_mode);
> > + if (ret < 0)
> > + return ret;
> >
> > + panel->backlight.max = panel->backlight.edp.vesa.info.max;
> > panel->backlight.min = 0;
> > - panel->backlight.level = intel_dp_aux_vesa_get_backlight(connector,
> > pipe);
> > - panel->backlight.enabled =
> > intel_dp_aux_vesa_backlight_dpcd_mode(connector) &&
> > - panel->backlight.level != 0;
> > + if (current_mode == DP_EDP_BACKLIGHT_CONTROL_MODE_DPCD) {
> > + panel->backlight.level = current_level;
> > + panel->backlight.enabled = panel->backlight.level != 0;
> > + } else {
> > + panel->backlight.level = panel->backlight.max;
> > + panel->backlight.enabled = false;
> > + }
> >
> > return 0;
> > }
> > @@ -559,16 +340,12 @@ intel_dp_aux_supports_vesa_backlight(struct
> > intel_connector *connector)
> > struct intel_dp *intel_dp = intel_attached_dp(connector);
> > struct drm_i915_private *i915 = dp_to_i915(intel_dp);
> >
> > - /* Check the eDP Display control capabilities registers to determine
> > if
> > - * the panel can support backlight control over the aux channel.
> > - *
> > - * TODO: We currently only support AUX only backlight
> > configurations, not backlights which
> > + /* TODO: We currently only support AUX only backlight
> > configurations, not backlights which
> > * require a mix of PWM and AUX controls to work. In the mean time,
> > these machines typically
> > * work just fine using normal PWM controls anyway.
> > */
> > - if (intel_dp->edp_dpcd[1] & DP_EDP_TCON_BACKLIGHT_ADJUSTMENT_CAP &&
> > - (intel_dp->edp_dpcd[1] & DP_EDP_BACKLIGHT_AUX_ENABLE_CAP) &&
> > - (intel_dp->edp_dpcd[2] &
> > DP_EDP_BACKLIGHT_BRIGHTNESS_AUX_SET_CAP)) {
> > + if ((intel_dp->edp_dpcd[1] & DP_EDP_BACKLIGHT_AUX_ENABLE_CAP) &&
> > + drm_edp_backlight_supported(intel_dp->edp_dpcd)) {
> > drm_dbg_kms(&i915->drm, "AUX Backlight Control
> > Supported!\n");
> > return true;
> > }
> > diff --git a/include/drm/drm_dp_helper.h b/include/drm/drm_dp_helper.h
> > index edffd1dcca3e..1eca0b42fc45 100644
> > --- a/include/drm/drm_dp_helper.h
> > +++ b/include/drm/drm_dp_helper.h
> > @@ -1790,6 +1790,24 @@ drm_dp_sink_can_do_video_without_timing_msa(const u8
> > dpcd[DP_RECEIVER_CAP_SIZE])
> > DP_MSA_TIMING_PAR_IGNORED;
> > }
> >
> > +/**
> > + * drm_edp_backlight_supported() - Check an eDP DPCD for VESA backlight
> > support
> > + * @edp_dpcd: The DPCD to check
> > + *
> > + * Note that currently this function will return %false for panels which
> > support various DPCD
> > + * backlight features but which require the brightness be set through PWM,
> > and don't support setting
> > + * the brightness level via the DPCD. This is a TODO.
> > + *
> > + * Returns: %True if @edp_dpcd indicates that VESA backlight controls are
> > supported, %false
> > + * otherwise
> > + */
> > +static inline bool
> > +drm_edp_backlight_supported(const u8 edp_dpcd[EDP_DISPLAY_CTL_CAP_SIZE])
> > +{
> > + return (edp_dpcd[1] & DP_EDP_TCON_BACKLIGHT_ADJUSTMENT_CAP) &&
> > + (edp_dpcd[2] & DP_EDP_BACKLIGHT_BRIGHTNESS_AUX_SET_CAP);
> > +}
> > +
> > /*
> > * DisplayPort AUX channel
> > */
> > @@ -2089,6 +2107,36 @@ drm_dp_has_quirk(const struct drm_dp_desc *desc, enum
> > drm_dp_quirk quirk)
> > return desc->quirks & BIT(quirk);
> > }
> >
> > +/**
> > + * struct drm_edp_backlight_info - Probed eDP backlight info struct
> > + * @pwmgen_bit_count: The pwmgen bit count
> > + * @pwm_freq_pre_divider: The PWM frequency pre-divider value being used
> > for this backlight, if any
> > + * @max: The maximum backlight level that may be set
> > + * @lsb_reg_used: Do we also write values to the
> > DP_EDP_BACKLIGHT_BRIGHTNESS_LSB register?
> > + * @aux_enable: Does the panel support the AUX enable cap?
> > + *
> > + * This structure contains various data about an eDP backlight, which can
> > be populated by using
> > + * drm_edp_backlight_init().
> > + */
> > +struct drm_edp_backlight_info {
> > + u8 pwmgen_bit_count;
> > + u8 pwm_freq_pre_divider;
> > + u16 max;
> > +
> > + bool lsb_reg_used : 1;
> > + bool aux_enable : 1;
> > +};
> > +
> > +int
> > +drm_edp_backlight_init(struct drm_dp_aux *aux, struct
> > drm_edp_backlight_info *bl,
> > + u16 driver_pwm_freq_hz, const u8
> > edp_dpcd[EDP_DISPLAY_CTL_CAP_SIZE],
> > + u16 *current_level, u8 *current_mode);
> > +int drm_edp_backlight_set_level(struct drm_dp_aux *aux, const struct
> > drm_edp_backlight_info *bl,
> > + u16 level);
> > +int drm_edp_backlight_enable(struct drm_dp_aux *aux, const struct
> > drm_edp_backlight_info *bl,
> > + u16 level);
> > +int drm_edp_backlight_disable(struct drm_dp_aux *aux, const struct
> > drm_edp_backlight_info *bl);
> > +
> > #ifdef CONFIG_DRM_DP_CEC
> > void drm_dp_cec_irq(struct drm_dp_aux *aux);
> > void drm_dp_cec_register_connector(struct drm_dp_aux *aux,
> > --
> > 2.29.2
> >
> > _______________________________________________
> > Intel-gfx mailing list
> > Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
> > https://lists.freedesktop.org/mailman/listinfo/intel-gfx
>
--
Sincerely,
Lyude Paul (she/her)
Software Engineer at Red Hat
Note: I deal with a lot of emails and have a lot of bugs on my plate. If you've
asked me a question, are waiting for a review/merge on a patch, etc. and I
haven't responded in a while, please feel free to send me another email to check
on my status. I don't bite!
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
