Hi,
On 1/8/21 10:23 AM, Maxime Ripard wrote:
Hi,
Thanks for those patches
On Thu, Jan 07, 2021 at 03:30:32AM +0100, Giulio Benetti wrote:
From: Giulio Benetti <giulio.benetti@xxxxxxxxxxxxxxxx>
It turned out(Maxime suggestion) that bit 26 of SUN4I_TCON0_IO_POL_REG is
dedicated to invert DCLK polarity and this makes thing really easier than
before. So let's handle DCLK polarity by adding
SUN4I_TCON0_IO_POL_DCLK_POSITIVE as bit 26 and activating according to
bus_flags the same way is done for all the other signals.
Cc: Maxime Ripard <maxime@xxxxxxxxxx>
Suggested-by would be nice here :)
Ok, didn't know about this tag
Signed-off-by: Giulio Benetti <giulio.benetti@xxxxxxxxxxxxxxxx>
---
drivers/gpu/drm/sun4i/sun4i_tcon.c | 20 +-------------------
drivers/gpu/drm/sun4i/sun4i_tcon.h | 1 +
2 files changed, 2 insertions(+), 19 deletions(-)
diff --git a/drivers/gpu/drm/sun4i/sun4i_tcon.c b/drivers/gpu/drm/sun4i/sun4i_tcon.c
index 52598bb0fb0b..30171ccd87e5 100644
--- a/drivers/gpu/drm/sun4i/sun4i_tcon.c
+++ b/drivers/gpu/drm/sun4i/sun4i_tcon.c
@@ -569,26 +569,8 @@ static void sun4i_tcon0_mode_set_rgb(struct sun4i_tcon *tcon,
if (info->bus_flags & DRM_BUS_FLAG_DE_LOW)
val |= SUN4I_TCON0_IO_POL_DE_NEGATIVE;
- /*
- * On A20 and similar SoCs, the only way to achieve Positive Edge
- * (Rising Edge), is setting dclk clock phase to 2/3(240°).
- * By default TCON works in Negative Edge(Falling Edge),
- * this is why phase is set to 0 in that case.
- * Unfortunately there's no way to logically invert dclk through
- * IO_POL register.
- * The only acceptable way to work, triple checked with scope,
- * is using clock phase set to 0° for Negative Edge and set to 240°
- * for Positive Edge.
- * On A33 and similar SoCs there would be a 90° phase option,
- * but it divides also dclk by 2.
- * Following code is a way to avoid quirks all around TCON
- * and DOTCLOCK drivers.
- */
if (info->bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE)
- clk_set_phase(tcon->dclk, 0);
-
- if (info->bus_flags & DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE)
- clk_set_phase(tcon->dclk, 240);
+ val |= SUN4I_TCON0_IO_POL_DCLK_POSITIVE;
I'm not really sure why we need the first patch of this series here?
The idea was to have 2 for testing, 1st one is already applicable, while
the other must be tested, but I can send only one with no problem.
That patch only seem to undo what you did in patch 1
No, it doesn't, the 2nd one change the way it achieve the same thing,
because the 1st swap DCLK phase, while the 2nd uses the IO_POL bit to
set IO polarity according to bus_flags.
Best Regards
--
Giulio Benetti
Benetti Engineering sas
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
