On 17/12/2020 19:06, Dmitry Osipenko wrote:
> Enable CPU voltage scaling and thermal throttling on Tegra30 Cardhu board.
>
> Signed-off-by: Dmitry Osipenko <digetx@xxxxxxxxx>
> ---
Same comments as 47/48
> arch/arm/boot/dts/tegra30-cardhu.dtsi | 61 ++++++++++++++++++++++++++-
> 1 file changed, 60 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/boot/dts/tegra30-cardhu.dtsi b/arch/arm/boot/dts/tegra30-cardhu.dtsi
> index d74c9ca78a7f..08c0ea4e6228 100644
> --- a/arch/arm/boot/dts/tegra30-cardhu.dtsi
> +++ b/arch/arm/boot/dts/tegra30-cardhu.dtsi
> @@ -1,6 +1,9 @@
> // SPDX-License-Identifier: GPL-2.0
> #include <dt-bindings/input/input.h>
> +#include <dt-bindings/thermal/thermal.h>
> #include "tegra30.dtsi"
> +#include "tegra30-cpu-opp.dtsi"
> +#include "tegra30-cpu-opp-microvolt.dtsi"
>
> /**
> * This file contains common DT entry for all fab version of Cardhu.
> @@ -339,12 +342,13 @@ ldo8_reg: ldo8 {
> };
> };
>
> - temperature-sensor@4c {
> + nct1008: temperature-sensor@4c {
> compatible = "onnn,nct1008";
> reg = <0x4c>;
> vcc-supply = <&sys_3v3_reg>;
> interrupt-parent = <&gpio>;
> interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_LEVEL_LOW>;
> + #thermal-sensor-cells = <1>;
> };
>
> vdd_core: tps62361@60 {
> @@ -438,6 +442,29 @@ clk32k_in: clock@0 {
> #clock-cells = <0>;
> };
>
> + cpus {
> + cpu0: cpu@0 {
> + cpu-supply = <&vddctrl_reg>;
> + operating-points-v2 = <&cpu0_opp_table>;
> + #cooling-cells = <2>;
> + };
> +
> + cpu@1 {
> + cpu-supply = <&vddctrl_reg>;
> + operating-points-v2 = <&cpu0_opp_table>;
> + };
> +
> + cpu@2 {
> + cpu-supply = <&vddctrl_reg>;
> + operating-points-v2 = <&cpu0_opp_table>;
> + };
> +
> + cpu@3 {
> + cpu-supply = <&vddctrl_reg>;
> + operating-points-v2 = <&cpu0_opp_table>;
> + };
> + };
> +
> panel: panel {
> compatible = "chunghwa,claa101wb01";
> ddc-i2c-bus = <&panelddc>;
> @@ -617,6 +644,38 @@ sound {
> <&tegra_car TEGRA30_CLK_EXTERN1>;
> };
>
> + thermal-zones {
> + cpu-thermal {
> + polling-delay-passive = <1000>; /* milliseconds */
> + polling-delay = <5000>; /* milliseconds */
> +
> + thermal-sensors = <&nct1008 1>;
> +
> + trips {
> + trip0: cpu-alert0 {
> + /* throttle at 57C until temperature drops to 56.8C */
> + temperature = <57000>;
> + hysteresis = <200>;
> + type = "passive";
> + };
> +
> + trip1: cpu-crit {
> + /* shut down at 60C */
> + temperature = <60000>;
> + hysteresis = <2000>;
> + type = "critical";
> + };
> + };
> +
> + cooling-maps {
> + map0 {
> + trip = <&trip0>;
> + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> + };
> + };
> + };
> + };
> +
> gpio-keys {
> compatible = "gpio-keys";
>
>
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
