[PATCH v4 05/21] gpu: host1x: Use HW-equivalent syncpoint expiration check

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Make syncpoint expiration checks always use the same logic used by
the hardware. This ensures that there are no race conditions that
could occur because of the hardware triggering a syncpoint interrupt
and then the driver disagreeing.

One situation where this could occur is if a job incremented a
syncpoint too many times -- then the hardware would trigger an
interrupt, but the driver would assume that a syncpoint value
greater than the syncpoint's max value is in the future, and not
clean up the job.

Signed-off-by: Mikko Perttunen <mperttunen@xxxxxxxxxx>
---
 drivers/gpu/host1x/syncpt.c | 51 ++-----------------------------------
 1 file changed, 2 insertions(+), 49 deletions(-)

diff --git a/drivers/gpu/host1x/syncpt.c b/drivers/gpu/host1x/syncpt.c
index 5982fdf64e1c..9ca0d852e32f 100644
--- a/drivers/gpu/host1x/syncpt.c
+++ b/drivers/gpu/host1x/syncpt.c
@@ -306,59 +306,12 @@ EXPORT_SYMBOL(host1x_syncpt_wait);
 bool host1x_syncpt_is_expired(struct host1x_syncpt *sp, u32 thresh)
 {
 	u32 current_val;
-	u32 future_val;
 
 	smp_rmb();
 
 	current_val = (u32)atomic_read(&sp->min_val);
-	future_val = (u32)atomic_read(&sp->max_val);
-
-	/* Note the use of unsigned arithmetic here (mod 1<<32).
-	 *
-	 * c = current_val = min_val	= the current value of the syncpoint.
-	 * t = thresh			= the value we are checking
-	 * f = future_val  = max_val	= the value c will reach when all
-	 *				  outstanding increments have completed.
-	 *
-	 * Note that c always chases f until it reaches f.
-	 *
-	 * Dtf = (f - t)
-	 * Dtc = (c - t)
-	 *
-	 *  Consider all cases:
-	 *
-	 *	A) .....c..t..f.....	Dtf < Dtc	need to wait
-	 *	B) .....c.....f..t..	Dtf > Dtc	expired
-	 *	C) ..t..c.....f.....	Dtf > Dtc	expired	   (Dct very large)
-	 *
-	 *  Any case where f==c: always expired (for any t).	Dtf == Dcf
-	 *  Any case where t==c: always expired (for any f).	Dtf >= Dtc (because Dtc==0)
-	 *  Any case where t==f!=c: always wait.		Dtf <  Dtc (because Dtf==0,
-	 *							Dtc!=0)
-	 *
-	 *  Other cases:
-	 *
-	 *	A) .....t..f..c.....	Dtf < Dtc	need to wait
-	 *	A) .....f..c..t.....	Dtf < Dtc	need to wait
-	 *	A) .....f..t..c.....	Dtf > Dtc	expired
-	 *
-	 *   So:
-	 *	   Dtf >= Dtc implies EXPIRED	(return true)
-	 *	   Dtf <  Dtc implies WAIT	(return false)
-	 *
-	 * Note: If t is expired then we *cannot* wait on it. We would wait
-	 * forever (hang the system).
-	 *
-	 * Note: do NOT get clever and remove the -thresh from both sides. It
-	 * is NOT the same.
-	 *
-	 * If future valueis zero, we have a client managed sync point. In that
-	 * case we do a direct comparison.
-	 */
-	if (!host1x_syncpt_client_managed(sp))
-		return future_val - thresh >= current_val - thresh;
-	else
-		return (s32)(current_val - thresh) >= 0;
+
+	return ((current_val - thresh) & 0x80000000U) == 0U;
 }
 
 int host1x_syncpt_init(struct host1x *host)
-- 
2.29.2

_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel



[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux