Add documentation for new optional properties in the exynos bus nodes:
interconnects, #interconnect-cells, samsung,data-clock-ratio.
These properties allow to specify the SoC interconnect structure which
then allows the interconnect consumer devices to request specific
bandwidth requirements.
Acked-by: Krzysztof Kozlowski <krzk@xxxxxxxxxx>
Acked-by: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
Tested-by: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
Acked-by: Rob Herring <robh@xxxxxxxxxx>
Signed-off-by: Artur Świgoń <a.swigon@xxxxxxxxxxx>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@xxxxxxxxxxx>
---
Changes for v9:
- added Ack tags
Changes for v8:
- updated description of the interconnects property,
- fixed typo in samsung,data-clk-ratio property description.
Changes for v7:
- bus-width property replaced with samsung,data-clock-ratio,
- the interconnect consumer bindings used instead of vendor specific
properties
Changes for v6:
- added dts example of bus hierarchy definition and the interconnect
consumer,
- added new bus-width property.
Changes for v5:
- exynos,interconnect-parent-node renamed to samsung,interconnect-parent
---
.../devicetree/bindings/devfreq/exynos-bus.txt | 71 +++++++++++++++++++++-
1 file changed, 69 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
index e71f752..bcaa2c0 100644
--- a/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
+++ b/Documentation/devicetree/bindings/devfreq/exynos-bus.txt
@@ -51,6 +51,19 @@ Optional properties only for parent bus device:
- exynos,saturation-ratio: the percentage value which is used to calibrate
the performance count against total cycle count.
+Optional properties for the interconnect functionality (QoS frequency
+constraints):
+- #interconnect-cells: should be 0.
+- interconnects: as documented in ../interconnect.txt, describes a path at the
+ higher level interconnects used by this interconnect provider.
+ If this interconnect provider is directly linked to a top level interconnect
+ provider the property contains only one phandle. The provider extends
+ the interconnect graph by linking its node to a node registered by provider
+ pointed to by first phandle in the 'interconnects' property.
+
+- samsung,data-clock-ratio: ratio of the data throughput in B/s to minimum data
+ clock frequency in Hz, default value is 8 when this property is missing.
+
Detailed correlation between sub-blocks and power line according to Exynos SoC:
- In case of Exynos3250, there are two power line as following:
VDD_MIF |--- DMC
@@ -135,7 +148,7 @@ Detailed correlation between sub-blocks and power line according to Exynos SoC:
|--- PERIC (Fixed clock rate)
|--- FSYS (Fixed clock rate)
-Example1:
+Example 1:
Show the AXI buses of Exynos3250 SoC. Exynos3250 divides the buses to
power line (regulator). The MIF (Memory Interface) AXI bus is used to
transfer data between DRAM and CPU and uses the VDD_MIF regulator.
@@ -184,7 +197,7 @@ Example1:
|L5 |200000 |200000 |400000 |300000 | ||1000000 |
----------------------------------------------------------
-Example2 :
+Example 2:
The bus of DMC (Dynamic Memory Controller) block in exynos3250.dtsi
is listed below:
@@ -419,3 +432,57 @@ Example2 :
devfreq = <&bus_leftbus>;
status = "okay";
};
+
+Example 3:
+ An interconnect path "bus_display -- bus_leftbus -- bus_dmc" on
+ Exynos4412 SoC with video mixer as an interconnect consumer device.
+
+ soc {
+ bus_dmc: bus_dmc {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_DIV_DMC>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_dmc_opp_table>;
+ samsung,data-clock-ratio = <4>;
+ #interconnect-cells = <0>;
+ };
+
+ bus_leftbus: bus_leftbus {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_DIV_GDL>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_leftbus_opp_table>;
+ #interconnect-cells = <0>;
+ interconnects = <&bus_dmc>;
+ };
+
+ bus_display: bus_display {
+ compatible = "samsung,exynos-bus";
+ clocks = <&clock CLK_ACLK160>;
+ clock-names = "bus";
+ operating-points-v2 = <&bus_display_opp_table>;
+ #interconnect-cells = <0>;
+ interconnects = <&bus_leftbus &bus_dmc>;
+ };
+
+ bus_dmc_opp_table: opp_table1 {
+ compatible = "operating-points-v2";
+ /* ... */
+ }
+
+ bus_leftbus_opp_table: opp_table3 {
+ compatible = "operating-points-v2";
+ /* ... */
+ };
+
+ bus_display_opp_table: opp_table4 {
+ compatible = "operating-points-v2";
+ /* .. */
+ };
+
+ &mixer {
+ compatible = "samsung,exynos4212-mixer";
+ interconnects = <&bus_display &bus_dmc>;
+ /* ... */
+ };
+ };
--
2.7.4
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
