Re: use of dma_direct_set_offset in (allwinner) drivers

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2020-11-04 08:14, Maxime Ripard wrote:
Hi Christoph,

On Tue, Nov 03, 2020 at 10:55:38AM +0100, Christoph Hellwig wrote:
Linux 5.10-rc1 switched from having a single dma offset in struct device
to a set of DMA ranges, and introduced a new helper to set them,
dma_direct_set_offset.

This in fact surfaced that a bunch of drivers that violate our layering
and set the offset from drivers, which meant we had to reluctantly
export the symbol to set up the DMA range.

The drivers are:

drivers/gpu/drm/sun4i/sun4i_backend.c

   This just use dma_direct_set_offset as a fallback.  Is there any good
   reason to not just kill off the fallback?

drivers/media/platform/sunxi/sun4i-csi/sun4i_csi.c

   Same as above.

So, the history of this is:

   - We initially introduced the support for those two controllers
     assuming that there was a direct mapping between the physical and
     DMA addresses. It turns out it didn't and the DMA accesses were
     going through a secondary, dedicated, bus that didn't have the same
     mapping of the RAM than the CPU.

     4690803b09c6 ("drm/sun4i: backend: Offset layer buffer address by DRAM starting address")

   - This dedicated bus is undocumented and barely used in the vendor
     kernel so this was overlooked, and it's fairly hard to get infos on
     it for all the SoCs we support. We added the DT support for it
     though on some SoCs we had enough infos to do so:

     c43a4469402f ("dt-bindings: interconnect: Add a dma interconnect name")
     22f88e311399 ("ARM: dts: sun5i: Add the MBUS controller")

     This explains the check on the interconnect property

   - However, due to the stable DT rule, we still need to operate without
     regressions on older DTs that wouldn't have that property (and for
     SoCs we haven't figured out). Hence the fallback.

How about having something in the platform code that keys off the top-level SoC compatible and uses a bus notifier to create offsets for the relevant devices if an MBUS description is missing? At least that way the workaround could be confined to a single dedicated place and look somewhat similar to other special cases like sta2x11, rather than being duplicated all over the place.

Robin.

drivers/media/platform/sunxi/sun6i-csi/sun6i_csi.c

   This driver unconditionally sets the offset.  Why can't we do this
   in the device tree?

drivers/staging/media/sunxi/cedrus/cedrus_hw.c

   Same as above.


We should make those two match the previous ones, but we'll have the
same issue here eventually. Most likely they were never ran on an SoC
for which we have the MBUS figured out.

Maxime


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel



[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux