On Tue, Oct 27, 2020 at 09:45:54AM -0700, Douglas Anderson wrote:
> The simple panel code currently allows panels to define fixed delays
> at certain stages of initialization. These work OK, but they don't
> really map all that clearly to the requirements presented in many
> panel datasheets. Instead of defining a fixed delay, those datasheets
> provide a timing diagram and specify a minimum amount of time that
> needs to pass from event A to event B.
>
> Because of the way things are currently defined, most panels end up
> over-delaying. One prime example here is that a number of panels I've
> looked at define the amount of time that must pass between turning a
> panel off and turning it back on again. Since there is no way to
> specify this, many developers have listed this as the "unprepare"
> delay. However, if nobody ever tried to turn the panel on again in
> the next 500 ms (or whatever the delay was) then this delay was
> pointless. It's better to do the delay only in the case that someone
> tried to turn the panel on too quickly.
>
> Let's support specifying delays as constraints. We'll start with the
> one above and also a second one: the minimum time between prepare
> being done and doing the enable. On the panel I'm looking at, there's
> an 80 ms minimum time between HPD being asserted by the panel and
> setting the backlight enable GPIO. By specifying as a constraint we
> can enforce this without over-delaying. Specifically the link
> training is allowed to happen in parallel with this delay so adding a
> fixed 80 ms delay isn't ideal.
>
> Signed-off-by: Douglas Anderson <dianders@xxxxxxxxxxxx>
> ---
>
> drivers/gpu/drm/panel/panel-simple.c | 51 ++++++++++++++++++++++++----
> 1 file changed, 44 insertions(+), 7 deletions(-)
This has always been bugging me a bit about the current setup, so I very
much like this idea.
>
> diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
> index 2be358fb46f7..cbbe71a2a940 100644
> --- a/drivers/gpu/drm/panel/panel-simple.c
> +++ b/drivers/gpu/drm/panel/panel-simple.c
> @@ -92,6 +92,19 @@ struct panel_desc {
> unsigned int unprepare;
> } delay;
>
> + /**
> + * @prepare_to_enable_ms: If this many milliseconds hasn't passed after
> + * prepare finished, add a delay to the start
> + * of enable.
> + * @unprepare_to_prepare_ms: If this many milliseconds hasn't passed
> + * unprepare finished, add a delay to the
> + * start of prepare.
I find this very difficult to understand and it's also not clear from
this what exactly the delay is. Perhaps this can be somewhat clarified
Something like the below perhaps?
@prepare_to_enable_ms: The minimum time, in milliseconds, that
needs to have passed between when prepare finished and enable
may begin. If at enable time less time has passed since
prepare finished, the driver waits for the remaining time.
> + */
> + struct {
> + unsigned int prepare_to_enable_ms;
> + unsigned int unprepare_to_prepare_ms;
> + } timing_constraints;
> +
> u32 bus_format;
> u32 bus_flags;
> int connector_type;
> @@ -99,10 +112,12 @@ struct panel_desc {
>
> struct panel_simple {
> struct drm_panel base;
> - bool prepared;
I understand how you're trying to reuse the value of prepared_time to
replace this flag, but I find the logic very hard to understand now.
> bool enabled;
> bool no_hpd;
>
> + ktime_t prepared_time;
> + ktime_t unprepared_time;
> +
> const struct panel_desc *desc;
>
> struct regulator *supply;
> @@ -230,6 +245,21 @@ static int panel_simple_get_non_edid_modes(struct panel_simple *panel,
> return num;
> }
>
> +static void panel_simple_enforce_constraint(ktime_t start_ktime,
> + unsigned int min_ms)
> +{
> + ktime_t now_ktime, min_ktime;
> +
> + if (!min_ms)
> + return;
> +
> + min_ktime = ktime_add(start_ktime, ms_to_ktime(min_ms));
> + now_ktime = ktime_get();
> +
> + if (ktime_before(now_ktime, min_ktime))
> + msleep(ktime_to_ms(ktime_sub(min_ktime, now_ktime)) + 1);
> +}
> +
> static int panel_simple_disable(struct drm_panel *panel)
> {
> struct panel_simple *p = to_panel_simple(panel);
> @@ -249,18 +279,19 @@ static int panel_simple_unprepare(struct drm_panel *panel)
> {
> struct panel_simple *p = to_panel_simple(panel);
>
> - if (!p->prepared)
> + if (!p->prepared_time)
> return 0;
Here for example I now need to actively think about what exactly
!prepared_time actually means, when all it really means is that we're
checking if the panel has already been enabled.
Perhaps we could provide a tiny helper to make this clearer?
static inline bool panel_simple_prepared(struct drm_panel *panel)
{
return p->prepared_time != 0;
}
I think that clarifies what's meant here. We could even add a comment
explaining what's going on here if that's still not clear.
Actually, looking at that, I think the explicit comparison alone makes
this clearer, so this already seems better to me as well:
if (p->prepared_time != 0)
return 0
Then again, this may just be me. If everyone else thinks this is clear
enough, feel free to leave it as-is.
Another alternative would be to leave the current flag and logic in
place and not rely on a special value for prepared_time to control the
flow. That's slightly redundant, but it's really just one flag.
> gpiod_set_value_cansleep(p->enable_gpio, 0);
>
> regulator_disable(p->supply);
>
> + p->prepared_time = 0;
> + p->unprepared_time = ktime_get();
> +
> if (p->desc->delay.unprepare)
> msleep(p->desc->delay.unprepare);
>
> - p->prepared = false;
> -
> return 0;
> }
>
> @@ -296,9 +327,12 @@ static int panel_simple_prepare(struct drm_panel *panel)
> int err;
> int hpd_asserted;
>
> - if (p->prepared)
> + if (p->prepared_time)
> return 0;
>
> + panel_simple_enforce_constraint(p->unprepared_time,
> + p->desc->timing_constraints.unprepare_to_prepare_ms);
Looking at this, perhaps we can come up with shorter names for these?
Thierry
Attachment:
signature.asc
Description: PGP signature
_______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
