On Tue, Sep 22, 2020 at 11:24 AM crj <algea.cao@xxxxxxxxxxxxxx> wrote: > > Hello Vicente, > > 在 2020/9/22 15:40, Andy Yan 写道: > > Add our HDMI driver owner Algea to list. > > > > On 9/22/20 2:18 AM, Vicente Bergas wrote: > >> Under certain conditions vop_crtc_mode_fixup rounds the clock > > > May I ask under what conditions that the clock of HDMI will > > be changed to 148501000? In general, the description of clock > > in EDID will not be detailed below the thousands place. There is no clock in the EDID with 1KHz resolution, the clock is 148500000 which has 500KHz resolution. It is the function vop_crtc_mode_fixup that gets xxx0000 and returns xxx1000 > >> 148500000 to 148501000 which leads to the following error: > >> dwhdmi-rockchip ff940000.hdmi: PHY configuration failed (clock > >> 148501000) > >> > >> The issue was found on RK3399 booting with u-boot. U-boot configures the > >> display at 2560x1440 and then linux comes up with a black screen. > >> A workaround was to un-plug and re-plug the HDMI display. > >> > >> Signed-off-by: Vicente Bergas <vicencb@xxxxxxxxx> > >> Tested-by: Vicente Bergas <vicencb@xxxxxxxxx> > >> --- > >> drivers/gpu/drm/rockchip/rockchip_drm_vop.c | 45 --------------------- > >> 1 file changed, 45 deletions(-) > >> > >> diff --git a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c > >> b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c > >> index c80f7d9fd13f..fe80da652994 100644 > >> --- a/drivers/gpu/drm/rockchip/rockchip_drm_vop.c > >> +++ b/drivers/gpu/drm/rockchip/rockchip_drm_vop.c > >> @@ -1142,50 +1142,6 @@ static void vop_crtc_disable_vblank(struct > >> drm_crtc *crtc) > >> spin_unlock_irqrestore(&vop->irq_lock, flags); > >> } > >> -static bool vop_crtc_mode_fixup(struct drm_crtc *crtc, > >> - const struct drm_display_mode *mode, > >> - struct drm_display_mode *adjusted_mode) > >> -{ > >> - struct vop *vop = to_vop(crtc); > >> - unsigned long rate; > >> - > >> - /* > >> - * Clock craziness. > >> - * > >> - * Key points: > >> - * > >> - * - DRM works in in kHz. > >> - * - Clock framework works in Hz. > >> - * - Rockchip's clock driver picks the clock rate that is the > >> - * same _OR LOWER_ than the one requested. > >> - * > >> - * Action plan: > >> - * > >> - * 1. When DRM gives us a mode, we should add 999 Hz to it. > >> That way > >> - * if the clock we need is 60000001 Hz (~60 MHz) and DRM > >> tells us to > >> - * make 60000 kHz then the clock framework will actually give us > >> - * the right clock. > >> - * > >> - * NOTE: if the PLL (maybe through a divider) could actually > >> make > >> - * a clock rate 999 Hz higher instead of the one we want then > >> this > >> - * could be a problem. Unfortunately there's not much we can do > >> - * since it's baked into DRM to use kHz. It shouldn't matter in > >> - * practice since Rockchip PLLs are controlled by tables and > >> - * even if there is a divider in the middle I wouldn't expect > >> PLL > >> - * rates in the table that are just a few kHz different. > >> - * > >> - * 2. Get the clock framework to round the rate for us to tell us > >> - * what it will actually make. > >> - * > >> - * 3. Store the rounded up rate so that we don't need to worry > >> about > >> - * this in the actual clk_set_rate(). > >> - */ > >> - rate = clk_round_rate(vop->dclk, adjusted_mode->clock * 1000 + > >> 999); > >> - adjusted_mode->clock = DIV_ROUND_UP(rate, 1000); > >> - > >> - return true; > >> -} > >> - > >> static bool vop_dsp_lut_is_enabled(struct vop *vop) > >> { > >> return vop_read_reg(vop, 0, &vop->data->common->dsp_lut_en); > >> @@ -1512,7 +1468,6 @@ static void vop_crtc_atomic_flush(struct > >> drm_crtc *crtc, > >> } > >> static const struct drm_crtc_helper_funcs vop_crtc_helper_funcs = { > >> - .mode_fixup = vop_crtc_mode_fixup, > >> .atomic_check = vop_crtc_atomic_check, > >> .atomic_begin = vop_crtc_atomic_begin, > >> .atomic_flush = vop_crtc_atomic_flush, _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel