Hi Robert,
On Fri, Aug 28, 2020 at 02:13:28PM +0300, Robert Chiras (OSS) wrote:
> From: Robert Chiras <robert.chiras@xxxxxxx>
>
> This patch adds support for a new clock 'video_pll' in order to better
> set the video_pll clock to a clock-rate that satisfies a mode's clock.
> The video PLL, on i.MX8MQ, can drive both DC pixel-clock and DSI phy_ref
> clock. When used with a bridge that can drive multiple modes, like a DSI
> to HDMI bridge, the DSI can't be statically configured for a specific
> mode in the DTS file.
> So, this patch adds access to the video PLL inside the DSI driver, so
> that modes can be filtered-out if the required combination of phy_ref
> and pixel-clock can't be achieved using the video PLL.
>
> Signed-off-by: Robert Chiras <robert.chiras@xxxxxxx>
> ---
> drivers/gpu/drm/bridge/nwl-dsi.c | 318 ++++++++++++++++++++++++++++++++++++++-
> 1 file changed, 313 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/gpu/drm/bridge/nwl-dsi.c b/drivers/gpu/drm/bridge/nwl-dsi.c
> index ce94f79..1228466 100644
> --- a/drivers/gpu/drm/bridge/nwl-dsi.c
> +++ b/drivers/gpu/drm/bridge/nwl-dsi.c
> @@ -39,6 +39,20 @@
>
> #define NWL_DSI_MIPI_FIFO_TIMEOUT msecs_to_jiffies(500)
>
> +/* Maximum Video PLL frequency: 1.2GHz */
> +#define MAX_PLL_FREQ 1200000000
> +
> +#define MBPS(x) ((x) * 1000000)
> +#define MIN_PHY_RATE MBPS(24)
> +#define MAX_PHY_RATE MBPS(30)
> +
> +/* Possible valid PHY reference clock rates*/
nitpick: missing ' ' at end of comment.
> +static u32 phyref_rates[] = {
> + 27000000,
> + 25000000,
> + 24000000,
> +};
> +
> enum transfer_direction {
> DSI_PACKET_SEND,
> DSI_PACKET_RECEIVE,
> @@ -67,6 +81,17 @@ struct nwl_dsi_transfer {
> size_t rx_len; /* in bytes */
> };
>
> +struct mode_config {
Maybe use nwl_mode_config ? There's so much other mode_config around an
this makes it obvious it's driver specific.
> + int clock;
> + int crtc_clock;
> + unsigned int lanes;
> + unsigned long bitclock;
> + unsigned long phy_rates[3];
> + unsigned long pll_rates[3];
> + int phy_rate_idx;
> + struct list_head list;
> +};
> +
> struct nwl_dsi {
> struct drm_bridge bridge;
> struct mipi_dsi_host dsi_host;
> @@ -101,6 +126,7 @@ struct nwl_dsi {
> struct clk *rx_esc_clk;
> struct clk *tx_esc_clk;
> struct clk *core_clk;
> + struct clk *pll_clk;
> /*
> * hardware bug: the i.MX8MQ needs this clock on during reset
> * even when not using LCDIF.
> @@ -115,6 +141,7 @@ struct nwl_dsi {
> int error;
>
> struct nwl_dsi_transfer *xfer;
> + struct list_head valid_modes;
> };
>
> static const struct regmap_config nwl_dsi_regmap_config = {
> @@ -778,6 +805,207 @@ static void nwl_dsi_bridge_disable(struct drm_bridge *bridge)
> pm_runtime_put(dsi->dev);
> }
>
> +static unsigned long nwl_dsi_get_bit_clock(struct nwl_dsi *dsi,
> + unsigned long pixclock, u32 lanes)
> +{
> + int bpp;
> +
> + if (lanes < 1 || lanes > 4)
> + return 0;
> +
> + bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
> +
> + return (pixclock * bpp) / lanes;
> +}
> +
> +/*
> + * Utility function to calculate least commom multiple, using an
> improved
s/commom/common/
> + * version of the Euclidean algorithm for greatest common factor.
> + */
> +static unsigned long nwl_dsi_get_lcm(unsigned long a, unsigned long b)
> +{
> + u32 gcf = 0; /* greatest common factor */
> + unsigned long tmp_a = a;
> + unsigned long tmp_b = b;
> +
> + if (!a || !b)
> + return 0;
> +
> + while (tmp_a % tmp_b) {
> + gcf = tmp_a % tmp_b;
> + tmp_a = tmp_b;
> + tmp_b = gcf;
> + }
> +
> + if (!gcf)
> + return a;
> +
> + return ((unsigned long long)a * b) / gcf;
> +}
> +
> +/*
> + * This function tries to adjust the crtc_clock for a DSI device in such a way
> + * that the video pll will be able to satisfy both Display Controller pixel
> + * clock (feeding out DPI interface) and our input phy_ref clock.
> + */
> +static void nwl_dsi_setup_pll_config(struct mode_config *config)
> +{
> + unsigned long pll_rate;
> + int div;
> + size_t i, num_rates = ARRAY_SIZE(config->phy_rates);
> +
> + config->crtc_clock = 0;
> +
> + for (i = 0; i < num_rates; i++) {
> + int crtc_clock;
> +
> + if (!config->phy_rates[i])
> + break;
> + /*
> + * First, we need to check if phy_ref can actually be obtained
> + * from pixel clock. To do this, we check their lowest common
> + * multiple, which has to be in PLL range.
> + */
> + pll_rate = nwl_dsi_get_lcm(config->clock, config->phy_rates[i]);
> + if (pll_rate > MAX_PLL_FREQ) {
> + /* Drop pll_rate to a realistic value */
> + while (pll_rate > MAX_PLL_FREQ)
> + pll_rate >>= 1;
> + /* Make sure pll_rate can provide phy_ref rate */
> + div = DIV_ROUND_UP(pll_rate, config->phy_rates[i]);
> + pll_rate = config->phy_rates[i] * div;
> + } else {
> + /*
> + * Increase the pll rate to highest possible rate for
> + * better accuracy.
> + */
> + while (pll_rate <= MAX_PLL_FREQ)
> + pll_rate <<= 1;
> + pll_rate >>= 1;
> + }
> +
> + /*
> + * Next, we need to tweak the pll_rate to a value that can also
> + * satisfy the crtc_clock.
> + */
> + div = DIV_ROUND_CLOSEST(pll_rate, config->clock);
> + if (lvl)
> + pll_rate -= config->phy_rates[i] * lvl;
lvl gets never defined so it doesn't compile breaking bisection.
> + crtc_clock = pll_rate / div;
> + config->pll_rates[i] = pll_rate;
> +
> + /*
> + * Pick a crtc_clock which is closest to pixel clock.
> + * Also, make sure that the pixel clock is a multiply of
> + * 50Hz.
> + */
> + if (!(crtc_clock % 50) &&
> + abs(config->clock - crtc_clock) <
> + abs(config->clock - config->crtc_clock)) {
> + config->crtc_clock = crtc_clock;
> + config->phy_rate_idx = i;
> + }
> + }
> +}
> +
> +
> +/*
> + * This function will try the required phy speed for current mode
> + * If the phy speed can be achieved, the phy will save the speed
> + * configuration
> + */
> +static struct mode_config *nwl_dsi_mode_probe(struct nwl_dsi *dsi,
> + const struct drm_display_mode *mode)
> +{
> + struct device *dev = dsi->dev;
> + struct mode_config *config;
> + union phy_configure_opts phy_opts;
> + unsigned long clock = mode->clock * 1000;
> + unsigned long bit_clk = 0;
> + unsigned long phy_rates[3] = {0};
> + int match_rates = 0;
> + u32 lanes = dsi->lanes;
> + size_t i = 0, num_rates = ARRAY_SIZE(phyref_rates);
> +
> + list_for_each_entry(config, &dsi->valid_modes, list)
> + if (config->clock == clock)
> + return config;
> +
> + phy_mipi_dphy_get_default_config(clock,
> + mipi_dsi_pixel_format_to_bpp(dsi->format),
> + lanes, &phy_opts.mipi_dphy);
> + phy_opts.mipi_dphy.lp_clk_rate = clk_get_rate(dsi->tx_esc_clk);
> +
> + while (i < num_rates) {
> + int ret;
> +
> + bit_clk = nwl_dsi_get_bit_clock(dsi, clock, lanes);
> +
> + clk_set_rate(dsi->pll_clk, phyref_rates[i] * 32);
> + clk_set_rate(dsi->phy_ref_clk, phyref_rates[i]);
> + ret = phy_validate(dsi->phy, PHY_MODE_MIPI_DPHY, 0, &phy_opts);
> +
> + /* Pick the non-failing rate, and search for more */
> + if (!ret) {
> + phy_rates[match_rates++] = phyref_rates[i++];
> + continue;
> + }
> +
> + if (match_rates)
> + break;
> +
> + /* Reached the end of phyref_rates, try another lane config */
> + if ((i++ == num_rates - 1) && (--lanes > 2)) {
> + i = 0;
> + continue;
> + }
> + }
> +
> + /*
> + * Try swinging between min and max pll rates and see what rate (in terms
> + * of kHz) we can custom use to get the required bit-clock.
> + */
> + if (!match_rates) {
> + int min_div, max_div;
> + int bit_clk_khz;
> +
> + lanes = dsi->lanes;
> + bit_clk = nwl_dsi_get_bit_clock(dsi, clock, lanes);
> +
> + min_div = DIV_ROUND_UP(bit_clk, MAX_PHY_RATE);
> + max_div = DIV_ROUND_DOWN_ULL(bit_clk, MIN_PHY_RATE);
> + bit_clk_khz = bit_clk / 1000;
> +
> + for (i = max_div; i > min_div; i--) {
> + if (!(bit_clk_khz % i)) {
> + phy_rates[0] = bit_clk / i;
> + match_rates = 1;
> + break;
> + }
> + }
> + }
> +
> + if (!match_rates) {
> + DRM_DEV_DEBUG_DRIVER(dev,
> + "Cannot setup PHY for mode: %ux%u @%d kHz\n",
> + mode->hdisplay,
> + mode->vdisplay,
> + mode->clock);
> +
> + return NULL;
> + }
> +
> + config = devm_kzalloc(dsi->dev, sizeof(struct mode_config), GFP_KERNEL);
> + config->clock = clock;
> + config->lanes = lanes;
> + config->bitclock = bit_clk;
> + memcpy(&config->phy_rates, &phy_rates, sizeof(phy_rates));
> + list_add(&config->list, &dsi->valid_modes);
> +
> + return config;
> +}
> +
> +
> static int nwl_dsi_get_dphy_params(struct nwl_dsi *dsi,
> const struct drm_display_mode *mode,
> union phy_configure_opts *phy_opts)
> @@ -809,6 +1037,38 @@ static bool nwl_dsi_bridge_mode_fixup(struct drm_bridge *bridge,
> const struct drm_display_mode *mode,
> struct drm_display_mode *adjusted_mode)
> {
> + struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> + struct mode_config *config;
> + unsigned long pll_rate;
> +
> + DRM_DEV_DEBUG_DRIVER(dsi->dev, "Fixup mode:\n");
> + drm_mode_debug_printmodeline(adjusted_mode);
> +
> + config = nwl_dsi_mode_probe(dsi, adjusted_mode);
Since this ends up calling `clk_set_rate` doesn't this violate the
`Drivers MUST NOT touch any persistent state` rule of the fixup
function? So would it be better to teach the phy about it's possible
rates rather then NWL? I guess that get's tricky your clock-drop-level
is dependent on the phy rate later on.
> + if (!config)
> + return false;
> +
> + DRM_DEV_DEBUG_DRIVER(dsi->dev, "lanes=%u, data_rate=%lu\n",
> + config->lanes, config->bitclock);
> + if (config->lanes < 2 || config->lanes > 4)
> + return false;
> +
> + /* Max data rate for this controller is 1.5Gbps */
> + if (config->bitclock > 1500000000)
> + return false;
> +
> + pll_rate = config->pll_rates[config->phy_rate_idx];
> + if (dsi->pll_clk && pll_rate) {
> + clk_set_rate(dsi->pll_clk, pll_rate);
> + DRM_DEV_DEBUG_DRIVER(dsi->dev,
> + "Video pll rate: %lu (actual: %lu)",
> + pll_rate, clk_get_rate(dsi->pll_clk));
> + }
> + /* Update the crtc_clock to be used by display controller */
> + if (config->crtc_clock)
> + adjusted_mode->crtc_clock = config->crtc_clock / 1000;
> +
> +
> /* At least LCDIF + NWL needs active high sync */
> adjusted_mode->flags |= (DRM_MODE_FLAG_PHSYNC | DRM_MODE_FLAG_PVSYNC);
> adjusted_mode->flags &= ~(DRM_MODE_FLAG_NHSYNC | DRM_MODE_FLAG_NVSYNC);
> @@ -822,14 +1082,29 @@ nwl_dsi_bridge_mode_valid(struct drm_bridge *bridge,
> const struct drm_display_mode *mode)
> {
> struct nwl_dsi *dsi = bridge_to_dsi(bridge);
> - int bpp = mipi_dsi_pixel_format_to_bpp(dsi->format);
> + struct mode_config *config;
> + unsigned long pll_rate;
> + int bit_rate;
>
> - if (mode->clock * bpp > 15000000 * dsi->lanes)
> + bit_rate = nwl_dsi_get_bit_clock(dsi, mode->clock * 1000, dsi->lanes);
> +
> + DRM_DEV_DEBUG_DRIVER(dsi->dev, "Validating mode:");
> + drm_mode_debug_printmodeline(mode);
These (and other locations) are a bit confusings since
`drm_mode_debug_printmodeline` uses DRM_DEBUG_KMS so if one only enabled
driver debugging (0x2) one gets: `Validating mode:` but then nothing.
> +
> + if (bit_rate > MBPS(1500))
> return MODE_CLOCK_HIGH;
>
> - if (mode->clock * bpp < 80000 * dsi->lanes)
> + if (bit_rate < MBPS(80))
> return MODE_CLOCK_LOW;
>
> + config = nwl_dsi_mode_probe(dsi, mode);
> + if (!config)
> + return MODE_NOCLOCK;
> +
> + pll_rate = config->pll_rates[config->phy_rate_idx];
> + if (dsi->pll_clk && !pll_rate)
> + nwl_dsi_setup_pll_config(config);
> +
> return MODE_OK;
> }
>
> @@ -842,8 +1117,22 @@ nwl_dsi_bridge_mode_set(struct drm_bridge *bridge,
> struct device *dev = dsi->dev;
> union phy_configure_opts new_cfg;
> unsigned long phy_ref_rate;
> + struct mode_config *config;
> int ret;
>
> + DRM_DEV_DEBUG_DRIVER(dsi->dev, "Setting mode:\n");
> + drm_mode_debug_printmodeline(adjusted_mode);
> +
> + config = nwl_dsi_mode_probe(dsi, adjusted_mode);
> + /* New mode? This should NOT happen */
> + if (!config) {
> + DRM_DEV_ERROR(dsi->dev, "Unsupported mode provided:\n");
> + drm_mode_debug_printmodeline(adjusted_mode);
> + return;
> + }
> +
> + phy_ref_rate = config->phy_rates[config->phy_rate_idx];
> + clk_set_rate(dsi->phy_ref_clk, phy_ref_rate);
> ret = nwl_dsi_get_dphy_params(dsi, adjusted_mode, &new_cfg);
> if (ret < 0)
> return;
> @@ -855,8 +1144,10 @@ nwl_dsi_bridge_mode_set(struct drm_bridge *bridge,
> if (new_cfg.mipi_dphy.hs_clk_rate == dsi->phy_cfg.mipi_dphy.hs_clk_rate)
> return;
>
> - phy_ref_rate = clk_get_rate(dsi->phy_ref_clk);
> - DRM_DEV_DEBUG_DRIVER(dev, "PHY at ref rate: %lu\n", phy_ref_rate);
> + DRM_DEV_DEBUG_DRIVER(dev,
> + "PHY at ref rate: %lu (actual: %lu)\n",
> + phy_ref_rate, clk_get_rate(dsi->phy_ref_clk));
> +
> /* Save the new desired phy config */
> memcpy(&dsi->phy_cfg, &new_cfg, sizeof(new_cfg));
>
> @@ -1014,6 +1305,12 @@ static int nwl_dsi_parse_dt(struct nwl_dsi *dsi)
> }
> dsi->tx_esc_clk = clk;
>
> + /* The video_pll clock is optional */
> + clk = devm_clk_get(dsi->dev, "video_pll");
Using devm_clk_get_optional return NULL so we can return a proper error
on other failures.
> + if (!IS_ERR(clk))
> + dsi->pll_clk = clk;
> +
> +
Drop one empty line.
Cheers,
-- Guido
> dsi->mux = devm_mux_control_get(dsi->dev, NULL);
> if (IS_ERR(dsi->mux)) {
> ret = PTR_ERR(dsi->mux);
> @@ -1066,6 +1363,9 @@ static int nwl_dsi_parse_dt(struct nwl_dsi *dsi)
> PTR_ERR(dsi->rst_dpi));
> return PTR_ERR(dsi->rst_dpi);
> }
> +
> + INIT_LIST_HEAD(&dsi->valid_modes);
> +
> return 0;
> }
>
> @@ -1184,6 +1484,14 @@ static int nwl_dsi_probe(struct platform_device *pdev)
> static int nwl_dsi_remove(struct platform_device *pdev)
> {
> struct nwl_dsi *dsi = platform_get_drvdata(pdev);
> + struct mode_config *config;
> + struct list_head *pos, *tmp;
> +
> + list_for_each_safe(pos, tmp, &dsi->valid_modes) {
> + config = list_entry(pos, struct mode_config, list);
> + list_del(pos);
> + devm_kfree(dsi->dev, config);
> + }
>
> nwl_dsi_deselect_input(dsi);
> mipi_dsi_host_unregister(&dsi->dsi_host);
> --
> 2.7.4
>
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
