Hi Maxime
On Wed, 8 Jul 2020 at 18:44, Maxime Ripard <maxime@xxxxxxxxxx> wrote:
>
> The VID_CTL setup is done in several places in the driver even though it's
> not really required. Let's simplify it a bit to do the configuration in one
> go.
>
> Signed-off-by: Maxime Ripard <maxime@xxxxxxxxxx>
Reviewed-by: Dave Stevenson <dave.stevenson@xxxxxxxxxxxxxxx>
> ---
> drivers/gpu/drm/vc4/vc4_hdmi.c | 14 ++++++--------
> 1 file changed, 6 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/gpu/drm/vc4/vc4_hdmi.c b/drivers/gpu/drm/vc4/vc4_hdmi.c
> index bbe521ab000b..f56a718a3643 100644
> --- a/drivers/gpu/drm/vc4/vc4_hdmi.c
> +++ b/drivers/gpu/drm/vc4/vc4_hdmi.c
> @@ -428,10 +428,6 @@ static void vc4_hdmi_set_timings(struct vc4_hdmi *vc4_hdmi,
>
> HDMI_WRITE(HDMI_VERTB0, vertb_even);
> HDMI_WRITE(HDMI_VERTB1, vertb);
> -
> - HDMI_WRITE(HDMI_VID_CTL,
> - (vsync_pos ? 0 : VC4_HD_VID_CTL_VSYNC_LOW) |
> - (hsync_pos ? 0 : VC4_HD_VID_CTL_HSYNC_LOW));
> }
>
> static void vc4_hdmi_recenter_fifo(struct vc4_hdmi *vc4_hdmi)
> @@ -520,8 +516,6 @@ static void vc4_hdmi_encoder_pre_crtc_configure(struct drm_encoder *encoder)
> if (vc4_hdmi->variant->phy_init)
> vc4_hdmi->variant->phy_init(vc4_hdmi, mode);
>
> - HDMI_WRITE(HDMI_VID_CTL, 0);
> -
> HDMI_WRITE(HDMI_SCHEDULER_CONTROL,
> HDMI_READ(HDMI_SCHEDULER_CONTROL) |
> VC4_HDMI_SCHEDULER_CONTROL_MANUAL_FORMAT |
> @@ -555,15 +549,19 @@ static void vc4_hdmi_encoder_pre_crtc_enable(struct drm_encoder *encoder)
>
> static void vc4_hdmi_encoder_post_crtc_enable(struct drm_encoder *encoder)
> {
> + struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode;
> struct vc4_hdmi *vc4_hdmi = encoder_to_vc4_hdmi(encoder);
> struct vc4_hdmi_encoder *vc4_encoder = to_vc4_hdmi_encoder(encoder);
> + bool hsync_pos = mode->flags & DRM_MODE_FLAG_PHSYNC;
> + bool vsync_pos = mode->flags & DRM_MODE_FLAG_PVSYNC;
> int ret;
>
> HDMI_WRITE(HDMI_VID_CTL,
> - HDMI_READ(HDMI_VID_CTL) |
> VC4_HD_VID_CTL_ENABLE |
> VC4_HD_VID_CTL_UNDERFLOW_ENABLE |
> - VC4_HD_VID_CTL_FRAME_COUNTER_RESET);
> + VC4_HD_VID_CTL_FRAME_COUNTER_RESET |
> + (vsync_pos ? 0 : VC4_HD_VID_CTL_VSYNC_LOW) |
> + (hsync_pos ? 0 : VC4_HD_VID_CTL_HSYNC_LOW));
>
> if (vc4_encoder->hdmi_monitor) {
> HDMI_WRITE(HDMI_SCHEDULER_CONTROL,
> --
> git-series 0.9.1
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
