On Mon, Jun 22, 2020 at 10:57 AM Daniel Thompson <daniel.thompson@xxxxxxxxxx> wrote: > > On Fri, Jun 19, 2020 at 11:53:41PM +0200, Sam Ravnborg wrote: > > > diff --git a/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml b/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml > > > new file mode 100644 > > > index 000000000000..7e1f109a38a4 > > > --- /dev/null > > > +++ b/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml > > > @@ -0,0 +1,98 @@ > > > +# SPDX-License-Identifier: GPL-2.0-only > > > +%YAML 1.2 > > > +--- > > > +$id: http://devicetree.org/schemas/leds/backlight/pwm-backlight.yaml# > > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > > + > > > +title: pwm-backlight bindings > > > + > > > +maintainers: > > > + - Lee Jones <lee.jones@xxxxxxxxxx> > > > + - Daniel Thompson <daniel.thompson@xxxxxxxxxx> > > > + - Jingoo Han <jingoohan1@xxxxxxxxx> > > > + > > > +properties: > > > + compatible: > > > + const: pwm-backlight > > > + > > > + pwms: > > > + maxItems: 1 > > > + > > > + pwm-names: true > > > + > > > + power-supply: > > > + description: regulator for supply voltage > > > + > > > + enable-gpios: > > > + description: Contains a single GPIO specifier for the GPIO which enables > > > + and disables the backlight > > > + maxItems: 1 > > > + > > > + post-pwm-on-delay-ms: > > > + description: Delay in ms between setting an initial (non-zero) PWM and > > > + enabling the backlight using GPIO. > > > + > > > + pwm-off-delay-ms: > > > + description: Delay in ms between disabling the backlight using GPIO > > > + and setting PWM value to 0. > > > + > > > + brightness-levels: > > > + description: Array of distinct brightness levels. Typically these are > > > + in the range from 0 to 255, but any range starting at 0 will do. The > > > + actual brightness level (PWM duty cycle) will be interpolated from > > > + these values. 0 means a 0% duty cycle (darkest/off), while the last > > > + value in the array represents a 100% duty cycle (brightest). > > > + $ref: /schemas/types.yaml#/definitions/uint32-array > > > + > > > + default-brightness-level: > > > + description: The default brightness level (index into the array defined > > > + by the "brightness-levels" property). > > > + $ref: /schemas/types.yaml#/definitions/uint32 > > Same comment as before... > > Sorry the "ditto" meant I didn't thing about PWM as much as I should > have. > > The situation for PWM is a little different to LED. That's mostly > because we decided not to clutter the LED code with > "num-interpolated-steps". > > The PWM code implements the default-brightness-level as an index into > the brightness array *after* it has been expanded using interpolation. > In other words today Linux treats the default-brightness-level more > like[1]. > > description: The default brightness level. When > num-interpolated-steps is not set this is simply an index into > the array defined by the "brightness-levels" property. If > num-interpolated-steps is set the brightness array will be > expanded by interpolation before we index to get a default > level. > > This is the best I have come up with so far... but I concede it still > lacks elegance. Happy to add this or whatever folks want if there's agreement, but I don't want to get bogged down on re-reviewing and re-writing the binding on what is just a conversion. There's a mountain of bindings to convert. Rob _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
