On Thu, Jun 18, 2020 at 04:44:13PM -0600, Rob Herring wrote: > Convert the common GPIO, LED, and PWM backlight bindings to DT schema > format. > > Given there's only 2 common properties and the descriptions are slightly > different, I opted to not create a common backlight schema. > > Cc: Lee Jones <lee.jones@xxxxxxxxxx> > Cc: Daniel Thompson <daniel.thompson@xxxxxxxxxx> > Cc: Jingoo Han <jingoohan1@xxxxxxxxx> > Signed-off-by: Rob Herring <robh@xxxxxxxxxx> ... > diff --git a/Documentation/devicetree/bindings/leds/backlight/led-backlight.yaml b/Documentation/devicetree/bindings/leds/backlight/led-backlight.yaml > new file mode 100644 > index 000000000000..ae50945d2798 > --- /dev/null > +++ b/Documentation/devicetree/bindings/leds/backlight/led-backlight.yaml > @@ -0,0 +1,58 @@ > +# SPDX-License-Identifier: GPL-2.0-only > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/leds/backlight/led-backlight.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: led-backlight bindings > + > +maintainers: > + - Lee Jones <lee.jones@xxxxxxxxxx> > + - Daniel Thompson <daniel.thompson@xxxxxxxxxx> > + - Jingoo Han <jingoohan1@xxxxxxxxx> > + > +description: > + This binding is used to describe a basic backlight device made of LEDs. It > + can also be used to describe a backlight device controlled by the output of > + a LED driver. > + > +properties: > + compatible: > + const: led-backlight > + > + leds: > + description: A list of LED nodes > + $ref: /schemas/types.yaml#/definitions/phandle-array > + > + brightness-levels: > + description: Array of distinct brightness levels. The levels must be > + in the range accepted by the underlying LED devices. This is used > + to translate a backlight brightness level into a LED brightness level. > + If it is not provided, the identity mapping is used. > + $ref: /schemas/types.yaml#/definitions/uint32-array > + > + default-brightness-level: > + description: The default brightness level (index into the array defined > + by the "brightness-levels" property). > + $ref: /schemas/types.yaml#/definitions/uint32 > + > +dependencies: > + default-brightness-level: [brightness-levels] I don't think there is a dependency here. default-brightness-level still makes sense with there is no mapping table present. Based on Sam's feedback perhaps adding ("if one is provided") to the parenthetic text. > diff --git a/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml b/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml > new file mode 100644 > index 000000000000..7e1f109a38a4 > --- /dev/null > +++ b/Documentation/devicetree/bindings/leds/backlight/pwm-backlight.yaml > @@ -0,0 +1,98 @@ > +# SPDX-License-Identifier: GPL-2.0-only > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/leds/backlight/pwm-backlight.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: pwm-backlight bindings > + > +maintainers: > + - Lee Jones <lee.jones@xxxxxxxxxx> > + - Daniel Thompson <daniel.thompson@xxxxxxxxxx> > + - Jingoo Han <jingoohan1@xxxxxxxxx> > + > +properties: > + compatible: > + const: pwm-backlight > + > + pwms: > + maxItems: 1 > + > + pwm-names: true > + > + power-supply: > + description: regulator for supply voltage > + > + enable-gpios: > + description: Contains a single GPIO specifier for the GPIO which enables > + and disables the backlight > + maxItems: 1 > + > + post-pwm-on-delay-ms: > + description: Delay in ms between setting an initial (non-zero) PWM and > + enabling the backlight using GPIO. > + > + pwm-off-delay-ms: > + description: Delay in ms between disabling the backlight using GPIO > + and setting PWM value to 0. > + > + brightness-levels: > + description: Array of distinct brightness levels. Typically these are > + in the range from 0 to 255, but any range starting at 0 will do. The > + actual brightness level (PWM duty cycle) will be interpolated from > + these values. 0 means a 0% duty cycle (darkest/off), while the last > + value in the array represents a 100% duty cycle (brightest). > + $ref: /schemas/types.yaml#/definitions/uint32-array > + > + default-brightness-level: > + description: The default brightness level (index into the array defined > + by the "brightness-levels" property). > + $ref: /schemas/types.yaml#/definitions/uint32 > + > + num-interpolated-steps: > + description: Number of interpolated steps between each value of brightness-levels > + table. This way a high resolution pwm duty cycle can be used without > + having to list out every possible value in the brightness-level array. > + $ref: /schemas/types.yaml#/definitions/uint32 > + > +dependencies: > + default-brightness-level: [brightness-levels] > + num-interpolated-steps: [brightness-levels] Just for the record, these dependencies are OK. Iit isn't really a good idea to map 1:1 to a PWM since we end up with a gazillion indistinguishable levels so the bindings (and the driver) to not allow such a mode. Daniel. _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
