Thanks Stephen for reviews.
I will post new change addressing your all comments.
On 2020-06-18 18:12, Stephen Boyd wrote:
Quoting Tanmay Shah (2020-06-18 16:21:13)
Enable DP driver for sc7180.
Add DP device node on sc7180? This isn't a driver.
Done.
This change depends-on following series:
https://patchwork.freedesktop.org/series/78583/
and https://patchwork.freedesktop.org/patch/351990/
Changes in v2:
- Add assigned-clocks and assigned-clock-parents
- Remove cell-index and pixel_rcg
- Change compatible to qcom,sc7180-dp
Signed-off-by: Tanmay Shah <tanmay@xxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/sc7180.dtsi | 57
++++++++++++++++++++++++++--
1 file changed, 53 insertions(+), 4 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi
b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index 916401f7e87c..26fe623e3b0f 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -2216,10 +2216,19 @@ ports {
#address-cells = <1>;
#size-cells = <0>;
+ port@1 {
+ reg = <1>;
+ dpu_intf1_out:
endpoint {
+
remote-endpoint =
+
<&dsi0_in>;
+ };
+ };
+
port@0 {
reg = <0>;
- dpu_intf1_out:
endpoint {
-
remote-endpoint = <&dsi0_in>;
+ dpu_intf0_out:
endpoint {
+
remote-endpoint =
+
<&dp_in>;
};
};
};
I thought this wasn't supposed to change? At least according to the
binding it shouldn't be needed.
Thanks. Yes it should be port@2 as per new dpu-sc7180.yaml bindings in
below patch.
https://patchwork.freedesktop.org/patch/371087/?series=78583&rev=1
@@ -2293,6 +2302,46 @@ dsi_phy: dsi-phy@ae94400 {
};
};
+ msm_dp: displayport-controller@ae90000{
+ status = "ok";
Please use status = "disabled";
Ok got it. Board's DT will enable it.
+ compatible = "qcom,sc7180-dp";
+
+ reg = <0 0xae90000 0 0x1400>;
+ reg-names = "dp_controller";
+
+ interrupt-parent = <&mdss>;
Any reason why this isn't under the mdss node like the other display
device nodes?
Done. Moved msm_dp node under mdss.
+ interrupts = <12 0>;
+
+ clocks = <&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
+ <&dispcc
DISP_CC_MDSS_DP_LINK_INTF_CLK>,
+ <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>;
+ clock-names = "core_aux", "ctrl_link",
+ "ctrl_link_iface",
"stream_pixel";
+ #clock-cells = <1>;
+ assigned-clocks = <&dispcc
DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
+ assigned-clock-parents = <&msm_dp 1>;
+
+ data-lanes = <0 1>;
This can and should be left to the board files. At the SoC level my
understanding is that there are four lanes possible, so no need to
artificially limit it here.
Removed from here. Driver changes I will be posting accordingly.
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ dp_in: endpoint {
+ remote-endpoint =
+
<&dpu_intf0_out>;
I'd prefer these were on one line, regardless of the 80 character line
limit/suggestion.
ok done.
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ dp_out: endpoint { };
+ };
+ };
+ };
+
dispcc: clock-controller@af00000 {
compatible = "qcom,sc7180-dispcc";
reg = <0 0x0af00000 0 0x200000>;
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
