Hi Eugeniu On Mon, Jun 08, 2020 at 11:44:32AM +0200, Eugeniu Rosca wrote: > Hello, > > Many thanks for your comments and involvement. > > On Sun, Jun 07, 2020 at 05:41:58AM +0300, Laurent Pinchart wrote: > > On Fri, Jun 05, 2020 at 03:53:15PM +0200, Jacopo Mondi wrote: > > > On Fri, Jun 05, 2020 at 03:41:24PM +0200, Eugeniu Rosca wrote: > > > > On Fri, Jun 05, 2020 at 03:29:00PM +0200, Jacopo Mondi wrote: > > > >> On Wed, May 27, 2020 at 09:15:55AM +0200, Eugeniu Rosca wrote: > > > >>> Could you kindly share the cross compilation steps for your kmsxx fork? > > > >> > > > >> I usually build it on the target :) > > > > > > > > Interesting approach. With ARM getting more and more potent, why not? :) > > > > > > For 'small' utilities like kmsxx it's doable > > > > > > >>> Just out of curiosity, have you ever tried to pull the display's HDMI > > > >>> cable while reading from CM2_LUT_TBL? > > > >> > > > >> Ahem, not really :) Did I get you right, you mean disconnecting the > > > >> HDMI cable from the board ? > > > > > > > > Right. > > > > > > So, no, I have not tried. Do you see any intersting failure with the > > > mainline version ? > > > > Jacopo, would you be able to give this a try ? > > FWIW, I seem to hit pre-existing issues in vanilla rcar-du, > while unplugging HDMI cable during a cyclic suspend-resume: > > HW: H3 ES2.0 Salvator-X > SW: renesas-drivers-2020-06-02-v5.7 > .config: renesas_defconfig +CONFIG_PM_DEBUG +CONFIG_PM_ADVANCED_DEBUG > Use-case: > > --------8<--------- > $ cat s2ram.sh > modprobe i2c-dev > echo 9 > /proc/sys/kernel/printk > i2cset -f -y 7 0x30 0x20 0x0F According to https://elinux.org/R-Car/Boards/Salvator-X#Suspend-to-RAM this is not needed anymore > echo 0 > /sys/module/suspend/parameters/pm_test_delay > echo core > /sys/power/pm_test > echo deep > /sys/power/mem_sleep > echo 1 > /sys/power/pm_debug_messages > echo 0 > /sys/power/pm_print_times > echo mem > /sys/power/state > > $ while true; do sh s2ram.sh ; done > $ # unplug HDMI cable several times I tried unplugging an plugging the cable while the system was suspended and after resume but I was not able to reproduce anything. Could you provide more precise instructions on how to reproduce this ? I.e. when to disconnect the cable to trigger the below error. Thanks j > > [ 55.568051] PM: noirq resume of devices complete after 3.862 msecs > [ 55.583253] PM: early resume of devices complete after 8.496 msecs > [ 65.757023] [drm:drm_atomic_helper_wait_for_flip_done] *ERROR* [CRTC:74:crtc-1] flip_done timed out > [ 75.996123] [drm:drm_atomic_helper_wait_for_flip_done] *ERROR* [CRTC:74:crtc-1] flip_done timed out > [ 86.236112] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CRTC:74:crtc-1] flip_done timed out > [ 96.476111] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CONNECTOR:80:HDMI-A-1] flip_done timed out > [ 106.716109] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [PLANE:45:plane-5] flip_done timed out > [ 116.956111] [drm:drm_atomic_helper_wait_for_flip_done] *ERROR* [CRTC:74:crtc-1] flip_done timed out > [ 127.196112] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CRTC:74:crtc-1] flip_done timed out > [ 137.436116] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [CONNECTOR:80:HDMI-A-1] flip_done timed out > [ 147.676111] [drm:drm_atomic_helper_wait_for_dependencies] *ERROR* [PLANE:45:plane-5] flip_done timed out > [ 157.916110] [drm:drm_atomic_helper_wait_for_flip_done] *ERROR* [CRTC:74:crtc-1] flip_done timed out > --------8<--------- > > This looks to be unrelated to the CMM lockup I initially reported. > > JYI, graphics pipelines in production R-Car3 targets are significantly > more complex (involving binding/unbinding serializer ICs at runtime > during non-trivial shutdown/suspend/resume sequences), as opposed > to the relatively straightforward VGA/HDMI outputs present on the > reference targets. So, my hope is that Renesas community can take > HDMI hot plugging seriously and make it a regular test-case during > rcar-du patch review, since this is a precondition for the R-Car3 > platform and products to succeed as a whole. > > BTW, if you happen to know an affordable programmable HDMI switcher > which can do the hot-plugging job in an automated test environment, > please let me know. > > > > > > >>> At least with the out-of-tree CMM implementation [*], this sends the > > > >>> R-Car3 reference targets into an unrecoverable freeze, with no lockup > > > >>> reported by the kernel (i.e. looks like an serious HW issue). > > > >>> > > > >>>> CMM functionalities are retained between suspend/resume cycles (tested with > > > >>>> suspend-to-idle) without requiring a re-programming of the LUT tables. > > > >>> > > > >>> Hmm. Is this backed up by any statement in the HW User's manual? > > > >>> This comes in contrast with the original Renesas CMM implementation [**] > > > >>> which does make use of suspend (where the freeze actually happens). > > > >>> > > > >>> Can we infer, based on your statement, that we could also get rid of > > > >>> the suspend callback in [**]? > > > >> > > > >> As Geert (thanks) explained what I've tested with is suspend-to-idle, > > > >> which retains the state of the LUT tables (and I assume other > > > >> not-yet-implemented CMM features, like CLU). I recall the out-of-tree > > > >> driver has suspend/resume routines but I never really tested that. > > > > > > > > I see. JFYI, there is a flaw in the suspend handling in the out-of-tree > > > > CMM patch [*], which renders the SoC unresponsive on HDMI hotplug. The > > > > fix is currently under review. Hopefully it will make its way to [*] > > > > in the nearest future. Just to keep in mind for the moment when CMM > > > > s2ram will become a mainline feature. > > > > > > Thanks, let's keep this in mind. Next week I'll run a few tests again > > > with s2ram and will get back to you. > > > > Note that the CMM driver is controlled by the DU driver. As the DU > > driver will reenable the display during resume, it will call > > rcar_du_cmm_setup() at resume time, which will reprogram the CMM. There > > should thus be no need for manual suspend/resume handling in the CMM as > > far as I can tell, but we need to ensure that the CMM is suspended > > before and resumed after the DU. I believe this could be implemented > > using device links. > > Does this apply to vanilla rcar-du only (where CMM support differs > from [*]) or would also be relevant for rcar.9.6 kernel? > > > > > > >>> [*] https://github.com/renesas-rcar/du_cmm > > > >>> [**] https://github.com/renesas-rcar/du_cmm/blob/c393ed49834bdbc/meta-rcar-gen3/recipes-kernel/linux/linux-renesas/0001-drm-rcar-du-Add-DU-CMM-support.patch#L1912 > > -- > Best regards, > Eugeniu Rosca _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
