On Tue, Jun 2, 2020 at 9:08 AM Maxime Ripard <maxime@xxxxxxxxxx> wrote: > > Hi Rob, > > On Fri, May 29, 2020 at 12:18:33PM -0600, Rob Herring wrote: > > On Wed, May 27, 2020 at 05:49:14PM +0200, Maxime Ripard wrote: > > > The HDMI controllers found in the BCM2711 SoC need some adjustments to the > > > bindings, especially since the registers have been shuffled around in more > > > register ranges. > > > > > > Cc: Rob Herring <robh+dt@xxxxxxxxxx> > > > Cc: devicetree@xxxxxxxxxxxxxxx > > > Signed-off-by: Maxime Ripard <maxime@xxxxxxxxxx> > > > --- > > > Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml | 109 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++- > > > 1 file changed, 109 insertions(+) > > > create mode 100644 Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml > > > > > > diff --git a/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml b/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml > > > new file mode 100644 > > > index 000000000000..6091fe3d315b > > > --- /dev/null > > > +++ b/Documentation/devicetree/bindings/display/brcm,bcm2711-hdmi.yaml > > > @@ -0,0 +1,109 @@ > > > +# SPDX-License-Identifier: GPL-2.0 > > > > Dual license... > > > > > +%YAML 1.2 > > > +--- > > > +$id: http://devicetree.org/schemas/display/brcm,bcm2711-hdmi.yaml# > > > +$schema: http://devicetree.org/meta-schemas/core.yaml# > > > + > > > +title: Broadcom BCM2711 HDMI Controller Device Tree Bindings > > > + > > > +maintainers: > > > + - Eric Anholt <eric@xxxxxxxxxx> > > > + > > > +properties: > > > + compatible: > > > + enum: > > > + - brcm,bcm2711-hdmi0 > > > + - brcm,bcm2711-hdmi1 > > > > What's the difference between the 2 blocks? > > The register layout and the lane mapping in the PHY change a bit. > > > > + > > > + reg: > > > + items: > > > + - description: HDMI controller register range > > > + - description: DVP register range > > > + - description: HDMI PHY register range > > > + - description: Rate Manager register range > > > + - description: Packet RAM register range > > > + - description: Metadata RAM register range > > > + - description: CSC register range > > > + - description: CEC register range > > > + - description: HD register range > > > + > > > + reg-names: > > > + items: > > > + - const: hdmi > > > + - const: dvp > > > + - const: phy > > > + - const: rm > > > + - const: packet > > > + - const: metadata > > > + - const: csc > > > + - const: cec > > > + - const: hd > > > + > > > + clocks: > > > + description: The HDMI state machine clock > > > + > > > + clock-names: > > > + const: hdmi > > > + > > > + ddc: > > > + allOf: > > > + - $ref: /schemas/types.yaml#/definitions/phandle > > > + description: > > > > + Phandle of the I2C controller used for DDC EDID probing > > > > Goes in the connector. > > > > And isn't the standard name ddc-i2c-bus? > > > > > + > > > + hpd-gpios: > > > + description: > > > > + The GPIO pin for the HDMI hotplug detect (if it doesn't appear > > > + as an interrupt/status bit in the HDMI controller itself) > > > > Goes in the connector. > > If this was an entirely new binding, I would agree, but this is not > really the case here. > > We discussed it already for the v2, and this binding is essentially the > same one than the bcm2835 HDMI controller. > > I initially sent a patch adding conditionnals for the clocks and regs > differences too, and you asked to split the binding into a separate file > to simplify it a bit. Ah... Best to assume I don't remember what happened last week. ;) > Supporting both the old binding, and the new one based on the connector > is going to make the code significantly more complicated, and I'm not > really sure why we would here. I'm not really sure I agree on the complexity, but that can be a discussion for another day. Reviewed-by: Rob Herring <robh@xxxxxxxxxx> Rob _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
