Re: [PATCH v3 032/105] drm/vc4: crtc: Enable and disable the PV in atomic_enable / disable

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

Am 02.06.20 um 21:31 schrieb Eric Anholt:
> On Tue, Jun 2, 2020 at 8:02 AM Dave Stevenson
> <dave.stevenson@xxxxxxxxxxxxxxx> wrote:
>> Hi Maxime and Eric
>>
>> On Tue, 2 Jun 2020 at 15:12, Maxime Ripard <maxime@xxxxxxxxxx> wrote:
>>> Hi Eric
>>>
>>> On Wed, May 27, 2020 at 09:54:44AM -0700, Eric Anholt wrote:
>>>> On Wed, May 27, 2020 at 8:50 AM Maxime Ripard <maxime@xxxxxxxxxx> wrote:
>>>>> The VIDEN bit in the pixelvalve currently being used to enable or disable
>>>>> the pixelvalve seems to not be enough in some situations, which whill end
>>>>> up with the pixelvalve stalling.
>>>>>
>>>>> In such a case, even re-enabling VIDEN doesn't bring it back and we need to
>>>>> clear the FIFO. This can only be done if the pixelvalve is disabled though.
>>>>>
>>>>> In order to overcome this, we can configure the pixelvalve during
>>>>> mode_set_no_fb, but only enable it in atomic_enable and flush the FIFO
>>>>> there, and in atomic_disable disable the pixelvalve again.
>>>> What displays has this been tested with?  Getting this sequencing
>>>> right is so painful, and things like DSI are tricky to get to light
>>>> up.
>>> That FIFO is between the HVS and the HDMI PVs, so this was obviously
>>> tested against that. Dave also tested the DSI output IIRC, so we should
>>> be covered here.
>> DSI wasn't working on the first patch set that Maxime sent - I haven't
>> tested this one as yet but will do so.
>> DPI was working early on to both an Adafruit 800x480 DPI panel, and
>> via a VGA666 as VGA.
>> HDMI is obviously working.
>> VEC is being ignored now. The clock structure is more restricted than
>> earlier chips, so to get the required clocks for the VEC without using
>> fractional divides it compromises the clock that other parts of the
>> system can run at (IIRC including the ARM). That's why the VEC has to
>> be explicitly enabled for the firmware to enable it as the only
>> output. It's annoying, but that's just a restriction of the chip.
> I'm more concerned with "make sure we don't regress pre-pi4 with this
> series" than "pi4 displays all work from the beginning"

unfortuntely i can confirm this. With this patch series (using Maxime's
git repo with multi_v7_defconfig) my Raspberry Pi 3 B hangs up while
starting X (screen stays black, heartbeat stops, no more output at the
debug UART). AFAIR v2 didn't had this issue.

Stefan

>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel



[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux