Using BIT() is preferred over manual shifts as it's more readable, handles the 1 << 31 case properly, and avoids other mistakes as shown by the DEBUG0_HSYNC and DEBUG0_VSYNC bits (that are currently unused). Use it. Signed-off-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx> Reviewed-by: Stefan Agner <stefan@xxxxxxxx> --- drivers/gpu/drm/mxsfb/mxsfb_regs.h | 56 +++++++++++++++--------------- 1 file changed, 28 insertions(+), 28 deletions(-) diff --git a/drivers/gpu/drm/mxsfb/mxsfb_regs.h b/drivers/gpu/drm/mxsfb/mxsfb_regs.h index 932d7ea08fd5..713d8f830135 100644 --- a/drivers/gpu/drm/mxsfb/mxsfb_regs.h +++ b/drivers/gpu/drm/mxsfb/mxsfb_regs.h @@ -28,51 +28,51 @@ #define LCDC_V4_DEBUG0 0x1d0 #define LCDC_V3_DEBUG0 0x1f0 -#define CTRL_SFTRST (1 << 31) -#define CTRL_CLKGATE (1 << 30) -#define CTRL_BYPASS_COUNT (1 << 19) -#define CTRL_VSYNC_MODE (1 << 18) -#define CTRL_DOTCLK_MODE (1 << 17) -#define CTRL_DATA_SELECT (1 << 16) +#define CTRL_SFTRST BIT(31) +#define CTRL_CLKGATE BIT(30) +#define CTRL_BYPASS_COUNT BIT(19) +#define CTRL_VSYNC_MODE BIT(18) +#define CTRL_DOTCLK_MODE BIT(17) +#define CTRL_DATA_SELECT BIT(16) #define CTRL_SET_BUS_WIDTH(x) (((x) & 0x3) << 10) #define CTRL_GET_BUS_WIDTH(x) (((x) >> 10) & 0x3) #define CTRL_BUS_WIDTH_MASK (0x3 << 10) #define CTRL_SET_WORD_LENGTH(x) (((x) & 0x3) << 8) #define CTRL_GET_WORD_LENGTH(x) (((x) >> 8) & 0x3) -#define CTRL_MASTER (1 << 5) -#define CTRL_DF16 (1 << 3) -#define CTRL_DF18 (1 << 2) -#define CTRL_DF24 (1 << 1) -#define CTRL_RUN (1 << 0) +#define CTRL_MASTER BIT(5) +#define CTRL_DF16 BIT(3) +#define CTRL_DF18 BIT(2) +#define CTRL_DF24 BIT(1) +#define CTRL_RUN BIT(0) -#define CTRL1_FIFO_CLEAR (1 << 21) +#define CTRL1_FIFO_CLEAR BIT(21) #define CTRL1_SET_BYTE_PACKAGING(x) (((x) & 0xf) << 16) #define CTRL1_GET_BYTE_PACKAGING(x) (((x) >> 16) & 0xf) -#define CTRL1_CUR_FRAME_DONE_IRQ_EN (1 << 13) -#define CTRL1_CUR_FRAME_DONE_IRQ (1 << 9) +#define CTRL1_CUR_FRAME_DONE_IRQ_EN BIT(13) +#define CTRL1_CUR_FRAME_DONE_IRQ BIT(9) #define TRANSFER_COUNT_SET_VCOUNT(x) (((x) & 0xffff) << 16) #define TRANSFER_COUNT_GET_VCOUNT(x) (((x) >> 16) & 0xffff) #define TRANSFER_COUNT_SET_HCOUNT(x) ((x) & 0xffff) #define TRANSFER_COUNT_GET_HCOUNT(x) ((x) & 0xffff) -#define VDCTRL0_ENABLE_PRESENT (1 << 28) -#define VDCTRL0_VSYNC_ACT_HIGH (1 << 27) -#define VDCTRL0_HSYNC_ACT_HIGH (1 << 26) -#define VDCTRL0_DOTCLK_ACT_FALLING (1 << 25) -#define VDCTRL0_ENABLE_ACT_HIGH (1 << 24) -#define VDCTRL0_VSYNC_PERIOD_UNIT (1 << 21) -#define VDCTRL0_VSYNC_PULSE_WIDTH_UNIT (1 << 20) -#define VDCTRL0_HALF_LINE (1 << 19) -#define VDCTRL0_HALF_LINE_MODE (1 << 18) +#define VDCTRL0_ENABLE_PRESENT BIT(28) +#define VDCTRL0_VSYNC_ACT_HIGH BIT(27) +#define VDCTRL0_HSYNC_ACT_HIGH BIT(26) +#define VDCTRL0_DOTCLK_ACT_FALLING BIT(25) +#define VDCTRL0_ENABLE_ACT_HIGH BIT(24) +#define VDCTRL0_VSYNC_PERIOD_UNIT BIT(21) +#define VDCTRL0_VSYNC_PULSE_WIDTH_UNIT BIT(20) +#define VDCTRL0_HALF_LINE BIT(19) +#define VDCTRL0_HALF_LINE_MODE BIT(18) #define VDCTRL0_SET_VSYNC_PULSE_WIDTH(x) ((x) & 0x3ffff) #define VDCTRL0_GET_VSYNC_PULSE_WIDTH(x) ((x) & 0x3ffff) #define VDCTRL2_SET_HSYNC_PERIOD(x) ((x) & 0x3ffff) #define VDCTRL2_GET_HSYNC_PERIOD(x) ((x) & 0x3ffff) -#define VDCTRL3_MUX_SYNC_SIGNALS (1 << 29) -#define VDCTRL3_VSYNC_ONLY (1 << 28) +#define VDCTRL3_MUX_SYNC_SIGNALS BIT(29) +#define VDCTRL3_VSYNC_ONLY BIT(28) #define SET_HOR_WAIT_CNT(x) (((x) & 0xfff) << 16) #define GET_HOR_WAIT_CNT(x) (((x) >> 16) & 0xfff) #define SET_VERT_WAIT_CNT(x) ((x) & 0xffff) @@ -80,11 +80,11 @@ #define VDCTRL4_SET_DOTCLK_DLY(x) (((x) & 0x7) << 29) /* v4 only */ #define VDCTRL4_GET_DOTCLK_DLY(x) (((x) >> 29) & 0x7) /* v4 only */ -#define VDCTRL4_SYNC_SIGNALS_ON (1 << 18) +#define VDCTRL4_SYNC_SIGNALS_ON BIT(18) #define SET_DOTCLK_H_VALID_DATA_CNT(x) ((x) & 0x3ffff) -#define DEBUG0_HSYNC (1 < 26) -#define DEBUG0_VSYNC (1 < 25) +#define DEBUG0_HSYNC BIT(26) +#define DEBUG0_VSYNC BIT(25) #define MXSFB_MIN_XRES 120 #define MXSFB_MIN_YRES 120 -- Regards, Laurent Pinchart _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
