Hi Sam,
Thanks for your comments, i will rework this panel driver after l3gd20 patch submission.
Sam Ravnborg <sam@xxxxxxxxxxxx> 于2020年5月8日周五 下午5:02写道：
Hi Dillon.
Patch submissions starts to look fine.
On Fri, May 08, 2020 at 12:13:14PM +0800, dillon.minfei@xxxxxxxxx wrote:
> From: dillon min <dillon.minfei@xxxxxxxxx>
>
> This is a driver for 320x240 TFT panels, accepting a rgb input
> streams that get adapted and scaled to the panel.
This driver is, I suppose, prepared to be a driver for ILI9341 based
panles, and as such not for a fixed resolution.
I expect (hope) we in the future will see more panels added.
As i checked ili9341 datasheets, this panel just support 240x320 resolution only. if i'm wrong , please correct me. thanks
This panel can support 9 different kinds of interface , "3/4-line Serial Interface" have been supported by tiny/ili9341.c. i was verified it
but the performance on stm32f4 is very low.
currently, i just have stm32f429-disco in hands, with 18-bit parallel rgb bus connected on this board. reference to panel-ilitek-ili9322 and panel-ilitek-ili9881 driver, i have some plan to rewrite this driver.
1 add your below comments in.
2 use dc-gpio, reset-gpio, rgb-interface-bits from dts to config panel interface.
3 drop regmap, porting drm_mipi_dbi's mipi_dbi_command to config panel paramter. like tiny/ili9341.c
4 support rgb-16, rgb-18 interface.
5 use optional regulator or power gpio to control panel's power, as panel power is always on for my board, so i can't test this part. could i add the code which can't be tested?
6 support rotation in panel config (currently , i rotate the screen by kernel cmdline paramter)
if you have any other common panel configuration should be add , please inform me.
thanks.
Some things to fix, see comments in the follwoing.
Sam
>
> Signed-off-by: dillon min <dillon.minfei@xxxxxxxxx>
> ---
> drivers/gpu/drm/panel/Kconfig | 8 +
> drivers/gpu/drm/panel/Makefile | 1 +
> drivers/gpu/drm/panel/panel-ilitek-ili9341.c | 561 +++++++++++++++++++++++++++
> 3 files changed, 570 insertions(+)
> create mode 100644 drivers/gpu/drm/panel/panel-ilitek-ili9341.c
>
> diff --git a/drivers/gpu/drm/panel/Kconfig b/drivers/gpu/drm/panel/Kconfig
> index a1723c1..e42692c 100644
> --- a/drivers/gpu/drm/panel/Kconfig
> +++ b/drivers/gpu/drm/panel/Kconfig
> @@ -95,6 +95,14 @@ config DRM_PANEL_ILITEK_IL9322
> Say Y here if you want to enable support for Ilitek IL9322
> QVGA (320x240) RGB, YUV and ITU-T BT.656 panels.
>
> +config DRM_PANEL_ILITEK_IL9341
ILI9341 - so the config name matches the name of the driver IC.
> + tristate "Ilitek ILI9341 240x320 QVGA panels"
> + depends on OF && SPI
> + select REGMAP
> + help
> + Say Y here if you want to enable support for Ilitek IL9341
> + QVGA (240x320) RGB panels.
See comment to the changelog, the driver is more generic - I assume.
So the wording here can be improved to express this.
Add support RGB 16bits and RGB 18bits bus only ?
> +
> config DRM_PANEL_ILITEK_ILI9881C
> tristate "Ilitek ILI9881C-based panels"
> depends on OF
> diff --git a/drivers/gpu/drm/panel/Makefile b/drivers/gpu/drm/panel/Makefile
> index 96a883c..d123543 100644
> --- a/drivers/gpu/drm/panel/Makefile
> +++ b/drivers/gpu/drm/panel/Makefile
> @@ -8,6 +8,7 @@ obj-$(CONFIG_DRM_PANEL_ELIDA_KD35T133) += panel-elida-kd35t133.o
> obj-$(CONFIG_DRM_PANEL_FEIXIN_K101_IM2BA02) += panel-feixin-k101-im2ba02.o
> obj-$(CONFIG_DRM_PANEL_FEIYANG_FY07024DI26A30D) += panel-feiyang-fy07024di26a30d.o
> obj-$(CONFIG_DRM_PANEL_ILITEK_IL9322) += panel-ilitek-ili9322.o
> +obj-$(CONFIG_DRM_PANEL_ILITEK_IL9341) += panel-ilitek-ili9341.o
> obj-$(CONFIG_DRM_PANEL_ILITEK_ILI9881C) += panel-ilitek-ili9881c.o
> obj-$(CONFIG_DRM_PANEL_INNOLUX_P079ZCA) += panel-innolux-p079zca.o
> obj-$(CONFIG_DRM_PANEL_JDI_LT070ME05000) += panel-jdi-lt070me05000.o
> diff --git a/drivers/gpu/drm/panel/panel-ilitek-ili9341.c b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c
> new file mode 100644
> index 0000000..ec22d80
> --- /dev/null
> +++ b/drivers/gpu/drm/panel/panel-ilitek-ili9341.c
> @@ -0,0 +1,561 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Ilitek ILI9341 TFT LCD drm_panel driver.
> + *
> + * This panel can be configured to support:
> + * - 16-bit parallel RGB interface
The interface to ILI9341 is SPI, and the interface between the ILI9341
and the panel is more of an itnernal thing. Or did I get this worng?
SPI is for register configuration. RGB parallel for data transfer
> + *
> + * Copyright (C) 2020 Dillon Min <dillon.minfei@xxxxxxxxx>
> + * Derived from drivers/drm/gpu/panel/panel-ilitek-ili9322.c
> + */
> +
> +#include <linux/bitops.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/regmap.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/spi/spi.h>
> +
> +#include <video/mipi_display.h>
> +#include <video/of_videomode.h>
> +#include <video/videomode.h>
> +
> +#include <drm/drm_modes.h>
> +#include <drm/drm_panel.h>
> +#include <drm/drm_print.h>
> +
> +#define DEFAULT_SPI_SPEED 10000000
> +
Please use same case for hex numbers in the driver.
My personal preferences is lower-case.
in next patch, spi speed will be configured by dts, not hardcode here.
below register address will change to lower-case hex numbers.
> +#define ILI9341_SLEEP_OUT 0x11 /* Sleep out register */
> +#define ILI9341_GAMMA 0x26 /* Gamma register */
> +#define ILI9341_DISPLAY_OFF 0x28 /* Display off register */
> +#define ILI9341_DISPLAY_ON 0x29 /* Display on register */
> +#define ILI9341_COLUMN_ADDR 0x2A /* Colomn address register */
> +#define ILI9341_PAGE_ADDR 0x2B /* Page address register */
> +#define ILI9341_GRAM 0x2C /* GRAM register */
> +#define ILI9341_MAC 0x36 /* Memory Access Control register*/
> +#define ILI9341_PIXEL_FORMAT 0x3A /* Pixel Format register */
> +#define ILI9341_WDB 0x51 /* Write Brightness Display
> + * register
> + */
> +#define ILI9341_WCD 0x53 /* Write Control Display
> + * register
> + */
> +#define ILI9341_RGB_INTERFACE 0xB0 /* RGB Interface Signal Control */
> +#define ILI9341_FRC 0xB1 /* Frame Rate Control register */
> +#define ILI9341_BPC 0xB5 /* Blanking Porch Control
> + * register
> + */
> +#define ILI9341_DFC 0xB6 /* Display Function Control
> + * register
> + */
> +#define ILI9341_POWER1 0xC0 /* Power Control 1 register */
> +#define ILI9341_POWER2 0xC1 /* Power Control 2 register */
> +#define ILI9341_VCOM1 0xC5 /* VCOM Control 1 register */
> +#define ILI9341_VCOM2 0xC7 /* VCOM Control 2 register */
> +#define ILI9341_POWERA 0xCB /* Power control A register */
> +#define ILI9341_POWERB 0xCF /* Power control B register */
> +#define ILI9341_PGAMMA 0xE0 /* Positive Gamma Correction
> + * register
> + */
> +#define ILI9341_NGAMMA 0xE1 /* Negative Gamma Correction
> + * register
> + */
> +#define ILI9341_DTCA 0xE8 /* Driver timing control A */
> +#define ILI9341_DTCB 0xEA /* Driver timing control B */
> +#define ILI9341_POWER_SEQ 0xED /* Power on sequence register */
> +#define ILI9341_3GAMMA_EN 0xF2 /* 3 Gamma enable register */
> +#define ILI9341_INTERFACE 0xF6 /* Interface control register */
> +#define ILI9341_PRC 0xF7 /* Pump ratio control register */
> +
All the following should be const.
ok
Can any of the below be replaces by DEFINED constants?
> +static u8 ili9341_cmd0[] = {0xc3, 0x08, 0x50};
> +static u8 ili9341_powerb[] = {0x00, 0xc1, 0x30};
> +static u8 ili9341_power_seq[] = {0x64, 0x03, 0x12, 0x81};
> +static u8 ili9341_dtca[] = {0x85, 0x00, 0x78};
> +static u8 ili9341_powera[] = {0x39, 0x2c, 0x00, 0x34, 0x02};
> +static u8 ili9341_prc[] = {0x20};
> +static u8 ili9341_dtcb[] = {0x00, 0x00};
> +static u8 ili9341_frc[] = {0x00, 0x1b};
> +static u8 ili9341_dfc1[] = {0x0a, 0xa2};
> +static u8 ili9341_power1[] = {0x10};
> +static u8 ili9341_power2[] = {0x10};
> +static u8 ili9341_vcom1[] = {0x45, 0x15};
> +static u8 ili9341_vcom2[] = {0x90};
> +static u8 ili9341_mac[] = {0xc8};
> +static u8 ili9341_gamma_en[] = {0x00};
> +static u8 ili9341_rgb_intr[] = {0xc2};
> +static u8 ili9341_dfc2[] = {0x0a, 0xa7, 0x27, 0x04};
> +static u8 ili9341_column_addr[] = {0x00, 0x00, 0x00, 0xef};
> +static u8 ili9341_page_addr[] = {0x00, 0x00, 0x01, 0x3f};
> +static u8 ili9341_intr[] = {0x01, 0x00, 0x06};
> +static u8 ili9341_gamma[] = {0x01};
> +static u8 ili9341_pgamma[] = {0x0f, 0x29, 0x24, 0x0c, 0x0e, 0x09, 0x4e, 0x78,
> + 0x3c, 0x09, 0x13, 0x05, 0x17, 0x11, 0x00};
> +static u8 ili9341_ngamma[] = {0x00, 0x16, 0x1b, 0x04, 0x11, 0x07, 0x31, 0x33,
> + 0x42, 0x05, 0x0c, 0x0a, 0x28, 0x2f, 0x0f};
> +
> +/**
> + * enum ili9341_input - the format of the incoming signal to the panel
> + *
> + * The panel can be connected to various input streams and four of them can
> + * be selected by electronic straps on the display. However it is possible
> + * to select another mode or override the electronic default with this
> + * setting.
> + */
> +enum ili9341_input {
> + ILI9341_INPUT_PRGB_THROUGH = 0x0,
> + ILI9341_INPUT_PRGB_ALIGNED = 0x1,
> + ILI9341_INPUT_UNKNOWN = 0xf,
> +};
> +
> +/**
> + * struct ili9341_config - the system specific ILI9341 configuration
> + * @width_mm: physical panel width [mm]
> + * @height_mm: physical panel height [mm]
> + * @input: the input/entry type used in this system, if this is set to
> + * ILI9341_INPUT_UNKNOWN the driver will try to figure it out by probing
> + * the hardware
> + * @dclk_active_high: data/pixel clock active high, data will be clocked
> + * in on the rising edge of the DCLK (this is usually the case).
> + * @de_active_high: DE (data entry) is active high
> + * @hsync_active_high: HSYNC is active high
> + * @vsync_active_high: VSYNC is active high
> + */
> +struct ili9341_config {
> + u32 width_mm;
> + u32 height_mm;
> + enum ili9341_input input;
> + bool dclk_active_high;
> + bool de_active_high;
> + bool hsync_active_high;
> + bool vsync_active_high;
> +};
> +
> +struct ili9341 {
> + struct device *dev;
> + const struct ili9341_config *conf;
> + struct drm_panel panel;
> + struct regmap *regmap;
> + struct gpio_desc *reset_gpio;
> + struct gpio_desc *dc_gpio;
> + enum ili9341_input input;
> + struct videomode vm;
videomode is not used. So drop this field and drop the include files
that are no logner needed.
ok
> +};
> +
> +static inline struct ili9341 *panel_to_ili9341(struct drm_panel *panel)
> +{
> + return container_of(panel, struct ili9341, panel);
> +}
> +
> +int ili9341_spi_transfer(struct spi_device *spi, u32 speed_hz,
> + u8 bpw, const void *buf, size_t len)
> +{
> + size_t max_chunk = spi_max_transfer_size(spi);
> + struct spi_transfer tr = {
const?
ok
> + .bits_per_word = bpw,
> + .speed_hz = speed_hz,
> + .len = len,
> + };
> + struct spi_message m;
> + size_t chunk;
> + int ret;
> +
> + spi_message_init_with_transfers(&m, &tr, 1);
> +
> + while (len) {
> + chunk = min(len, max_chunk);
> +
> + tr.tx_buf = buf;
> + tr.len = chunk;
> + buf += chunk;
> + len -= chunk;
> +
> + ret = spi_sync(spi, &m);
> + if (ret)
> + return ret;
> + }
> + return 0;
> +}
> +static int ili9341_regmap_spi_write(void *context, const void *data,
> + size_t count)
> +{
> + struct device *dev = context;
> + struct spi_device *spi = to_spi_device(dev);
> + struct ili9341 *ili = spi_get_drvdata(spi);
> + int ret = 0;
> +
> + gpiod_set_value_cansleep(ili->dc_gpio, 0);
> +
> + ret = ili9341_spi_transfer(spi, DEFAULT_SPI_SPEED, 8, data+0, 1);
> + if (ret || count == 1 ||
> + ((u8 *)data)[0] == ILI9341_GRAM ||
> + ((u8 *)data)[0] == ILI9341_DISPLAY_ON ||
> + ((u8 *)data)[0] == ILI9341_SLEEP_OUT ||
> + ((u8 *)data)[0] == ILI9341_DISPLAY_OFF)
> + return ret;
> +
> + gpiod_set_value_cansleep(ili->dc_gpio, 1);
> +
> + return ili9341_spi_transfer(spi, DEFAULT_SPI_SPEED, 8, data+1, count-1);
> +}
> +
> +static int ili9341_regmap_spi_read(void *context, const void *reg,
> + size_t reg_size, void *val, size_t val_size)
> +{
> + return 0;
> +}
Is this function really needed? If not delete it.
regmap will be drop in next patch.
> +
> +static struct regmap_bus ili9341_regmap_bus = {
> + .write = ili9341_regmap_spi_write,
> + .read = ili9341_regmap_spi_read,
> + .reg_format_endian_default = REGMAP_ENDIAN_BIG,
> + .val_format_endian_default = REGMAP_ENDIAN_BIG,
> +};
> +
> +static bool ili9341_volatile_reg(struct device *dev, unsigned int reg)
> +{
> + return false;
> +}
Is this function really nedded? If not delete it.
> +
> +static bool ili9341_writeable_reg(struct device *dev, unsigned int reg)
> +{
> + /* Just register 0 is read-only */
> + if (reg == 0x00)
> + return false;
> + return true;
> +}
> +
> +static const struct regmap_config ili9341_regmap_config = {
> + .reg_bits = 8,
> + .val_bits = 8,
> + .max_register = 0xff,
> + .cache_type = REGCACHE_RBTREE,
> + .volatile_reg = ili9341_volatile_reg,
> + .writeable_reg = ili9341_writeable_reg,
> +};
> +
No error checks - consider something like:
static int bulk_write(struct ili9341 *ili, u8 reg, const u8[] data, int len)
{
int err = ili->err;
if (!err) {
err = regmap_bulk_write(ili->regmap, reg, data, len);
if (err) {
dev_err(...);
ili->err = err;
}
}
return err;
}
Then you can use this in the following, and make this more readable.
ok, thanks for detail guide.
> +static int ili9341_init(struct drm_panel *panel, struct ili9341 *ili)
> +{
> + regmap_bulk_write(ili->regmap, 0xca,
> + ili9341_cmd0, sizeof(ili9341_cmd0));
> + regmap_bulk_write(ili->regmap, ILI9341_POWERB,
> + ili9341_powerb, sizeof(ili9341_powerb));
> + regmap_bulk_write(ili->regmap, ILI9341_POWER_SEQ,
> + ili9341_power_seq, sizeof(ili9341_power_seq));
> + regmap_bulk_write(ili->regmap, ILI9341_DTCA,
> + ili9341_dtca, sizeof(ili9341_dtca));
> + regmap_bulk_write(ili->regmap, ILI9341_POWERA,
> + ili9341_powera, sizeof(ili9341_powera));
> + regmap_write(ili->regmap, ILI9341_PRC, ili9341_prc[0]);
> + regmap_bulk_write(ili->regmap, ILI9341_DTCB,
> + ili9341_dtcb, sizeof(ili9341_dtcb));
> + regmap_bulk_write(ili->regmap, ILI9341_FRC,
> + ili9341_frc, sizeof(ili9341_frc));
> + regmap_bulk_write(ili->regmap, ILI9341_DFC,
> + ili9341_dfc1, sizeof(ili9341_dfc1));
> + regmap_write(ili->regmap, ILI9341_POWER1, ili9341_power1[0]);
> + regmap_write(ili->regmap, ILI9341_POWER2, ili9341_power2[0]);
> + regmap_bulk_write(ili->regmap, ILI9341_VCOM1,
> + ili9341_vcom1, sizeof(ili9341_vcom1));
> + regmap_write(ili->regmap, ILI9341_VCOM2, ili9341_vcom2[0]);
> + regmap_write(ili->regmap, ILI9341_MAC, ili9341_mac[0]);
> + regmap_write(ili->regmap, ILI9341_3GAMMA_EN, ili9341_gamma_en[0]);
> + regmap_write(ili->regmap, ILI9341_RGB_INTERFACE, ili9341_rgb_intr[0]);
> + regmap_bulk_write(ili->regmap, ILI9341_DFC,
> + ili9341_dfc2, sizeof(ili9341_dfc2));
> +
> + /* colomn address set */
> + regmap_bulk_write(ili->regmap, ILI9341_COLUMN_ADDR,
> + ili9341_column_addr, sizeof(ili9341_column_addr));
> +
> + /* Page Address Set */
> + regmap_bulk_write(ili->regmap, ILI9341_PAGE_ADDR,
> + ili9341_page_addr, sizeof(ili9341_page_addr));
> + regmap_bulk_write(ili->regmap, ILI9341_INTERFACE,
> + ili9341_intr, sizeof(ili9341_intr));
> + regmap_write(ili->regmap, ILI9341_GRAM, 0);
> + msleep(200);
> +
> + regmap_write(ili->regmap, ILI9341_GAMMA, ili9341_gamma[0]);
> + regmap_bulk_write(ili->regmap, ILI9341_PGAMMA,
> + ili9341_pgamma, sizeof(ili9341_pgamma));
> + regmap_bulk_write(ili->regmap, ILI9341_NGAMMA,
> + ili9341_ngamma, sizeof(ili9341_ngamma));
> + regmap_write(ili->regmap, ILI9341_SLEEP_OUT, 0);
> + msleep(200);
> +
> + regmap_write(ili->regmap, ILI9341_DISPLAY_ON, 0);
> +
> + /* GRAM start writing */
> + regmap_write(ili->regmap, ILI9341_GRAM, 0);
> +
> + dev_info(ili->dev, "initialized display\n");
> +
> + return 0;
> +}
> +
> +/*
> + * This power-on sequence if from the datasheet, page 57.
> + */
> +static int ili9341_power_on(struct ili9341 *ili)
> +{
> + /* Assert RESET */
> + gpiod_set_value(ili->reset_gpio, 1);
> +
> + msleep(20);
> +
> + /* De-assert RESET */
> + gpiod_set_value(ili->reset_gpio, 0);
> +
> + msleep(10);
> +
> + return 0;
> +}
> +
> +static int ili9341_power_off(struct ili9341 *ili)
> +{
Assert reset?
will add reset-pin control here.
> + return 0;
> +}
> +
> +static int ili9341_disable(struct drm_panel *panel)
> +{
> + struct ili9341 *ili = panel_to_ili9341(panel);
> + int ret;
> +
> + ret = regmap_write(ili->regmap, ILI9341_DISPLAY_OFF, 0);
> + if (ret) {
> + dev_err(ili->dev, "unable to go to standby mode\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int ili9341_unprepare(struct drm_panel *panel)
> +{
> + struct ili9341 *ili = panel_to_ili9341(panel);
> +
> + return ili9341_power_off(ili);
> +}
> +
> +static int ili9341_prepare(struct drm_panel *panel)
> +{
> + struct ili9341 *ili = panel_to_ili9341(panel);
> + int ret;
> +
> + ret = ili9341_power_on(ili);
> + if (ret < 0)
> + return ret;
> +
> + ret = ili9341_init(panel, ili);
> + if (ret < 0)
> + ili9341_unprepare(panel);
> +
> + return ret;
> +}
> +
> +static int ili9341_enable(struct drm_panel *panel)
> +{
> + struct ili9341 *ili = panel_to_ili9341(panel);
> + int ret;
> +
> + ret = regmap_write(ili->regmap, ILI9341_DISPLAY_ON, 0);
> + if (ret) {
> + dev_err(ili->dev, "unable to enable panel\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +/* This is the only mode listed for parallel RGB in the datasheet */
> +static const struct drm_display_mode prgb_320x240_mode = {
> + .clock = 6100,
> + .hdisplay = 240,
> + .hsync_start = 240 + 10,
> + .hsync_end = 240 + 10 + 10,
> + .htotal = 280,
> + .vdisplay = 320,
> + .vsync_start = 320 + 4,
> + .vsync_end = 320 + 4 + 2,
> + .vtotal = 328,
> + .vrefresh = 60,
> + .flags = 0,
> +};
> +
> +static int ili9341_get_modes(struct drm_panel *panel,
> + struct drm_connector *connector)
> +{
> + struct ili9341 *ili = panel_to_ili9341(panel);
> + struct drm_device *drm = connector->dev;
> + struct drm_display_mode *mode;
> + struct drm_display_info *info;
> +
> + info = &connector->display_info;
> + info->width_mm = ili->conf->width_mm;
> + info->height_mm = ili->conf->height_mm;
> + if (ili->conf->dclk_active_high)
> + info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE;
> + else
> + info->bus_flags |= DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE;
> +
> + if (ili->conf->de_active_high)
> + info->bus_flags |= DRM_BUS_FLAG_DE_HIGH;
> + else
> + info->bus_flags |= DRM_BUS_FLAG_DE_LOW;
> +
> + switch (ili->input) {
> + case ILI9341_INPUT_PRGB_THROUGH:
> + case ILI9341_INPUT_PRGB_ALIGNED:
> + mode = drm_mode_duplicate(drm, &prgb_320x240_mode);
> + break;
> + default:
> + mode = NULL;
> + break;
> + }
> + if (!mode) {
> + DRM_ERROR("bad mode or failed to add mode\n");
> + return -EINVAL;
> + }
> + drm_mode_set_name(mode);
> + /*
> + * This is the preferred mode because most people are going
> + * to want to use the display with VGA type graphics.
> + */
> + mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED;
> +
> + /* Set up the polarity */
> + if (ili->conf->hsync_active_high)
> + mode->flags |= DRM_MODE_FLAG_PHSYNC;
> + else
> + mode->flags |= DRM_MODE_FLAG_NHSYNC;
> + if (ili->conf->vsync_active_high)
> + mode->flags |= DRM_MODE_FLAG_PVSYNC;
> + else
> + mode->flags |= DRM_MODE_FLAG_NVSYNC;
> +
> + mode->width_mm = ili->conf->width_mm;
> + mode->height_mm = ili->conf->height_mm;
> + drm_mode_probed_add(connector, mode);
> +
> + return 1; /* Number of modes */
> +}
> +
> +static const struct drm_panel_funcs ili9341_drm_funcs = {
> + .disable = ili9341_disable,
> + .unprepare = ili9341_unprepare,
> + .prepare = ili9341_prepare,
> + .enable = ili9341_enable,
> + .get_modes = ili9341_get_modes,
> +};
> +
> +static int ili9341_probe(struct spi_device *spi)
> +{
> + struct device *dev = &spi->dev;
> + struct ili9341 *ili;
> + const struct regmap_config *regmap_config;
> + int ret;
> +
> + ili = devm_kzalloc(dev, sizeof(struct ili9341), GFP_KERNEL);
> + if (!ili)
> + return -ENOMEM;
> +
> + spi_set_drvdata(spi, ili);
> +
> + ili->dev = dev;
> + /*
> + * Every new incarnation of this display must have a unique
> + * data entry for the system in this driver.
> + */
> + ili->conf = of_device_get_match_data(dev);
> + if (!ili->conf) {
> + dev_err(dev, "missing device configuration\n");
> + return -ENODEV;
> + }
> +
> + ili->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
> + if (IS_ERR(ili->reset_gpio)) {
> + dev_err(dev, "failed to get RESET GPIO\n");
> + return PTR_ERR(ili->reset_gpio);
> + }
> +
> + ili->dc_gpio = devm_gpiod_get_optional(dev, "dc", GPIOD_OUT_LOW);
> + if (IS_ERR(ili->dc_gpio)) {
> + dev_err(dev, "failed to get DC GPIO\n");
> + return PTR_ERR(ili->dc_gpio);
> + }
> +
> + spi->bits_per_word = 8;
> + ret = spi_setup(spi);
> + if (ret < 0) {
> + dev_err(dev, "spi setup failed.\n");
> + return ret;
> + }
> +
> + regmap_config = &ili9341_regmap_config;
> +
> + ili->regmap = devm_regmap_init(dev, &ili9341_regmap_bus, dev,
> + regmap_config);
> + if (IS_ERR(ili->regmap)) {
> + dev_err(dev, "failed to allocate register map\n");
> + return PTR_ERR(ili->regmap);
> + }
> +
> + ili->input = ili->conf->input;
> +
> + drm_panel_init(&ili->panel, dev, &ili9341_drm_funcs,
> + DRM_MODE_CONNECTOR_DPI);
> +
> + return drm_panel_add(&ili->panel);
> +}
> +
> +static int ili9341_remove(struct spi_device *spi)
> +{
> + struct ili9341 *ili = spi_get_drvdata(spi);
> +
> + ili9341_power_off(ili);
> + drm_panel_remove(&ili->panel);
> +
> + return 0;
> +}
> +
> +/*
> + * The Stm32f429-disco board has a panel ili9341 connected to ltdc controller
> + */
> +static const struct ili9341_config ili9341_data = {
This should be named "disco" something as this is m32f429-disco
specific.
ok
> + .width_mm = 65,
> + .height_mm = 50,
> + .input = ILI9341_INPUT_PRGB_THROUGH,
> + .dclk_active_high = true,
> + .de_active_high = false,
> + .hsync_active_high = false,
> + .vsync_active_high = false,
> +};
> +
> +static const struct of_device_id ili9341_of_match[] = {
> + {
> + .compatible = "stm32f429,ltdc-panel",
> + .data = ""> > + },
> + {
> + .compatible = "ilitek,ili9341",
> + .data = ""> This part is wrong, as ilitek,ili9341 is just the generic part.
Only the first entry is relevant.
ok
> + },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, ili9341_of_match);
> +
> +static struct spi_driver ili9341_driver = {
> + .probe = ili9341_probe,
> + .remove = ili9341_remove,
> + .driver = {
> + .name = "panel-ilitek-ili9341",
> + .of_match_table = ili9341_of_match,
> + },
> +};
> +module_spi_driver(ili9341_driver);
> +
> +MODULE_AUTHOR("Dillon Min <dillon.minfei@xxxxxxxxx>");
> +MODULE_DESCRIPTION("ILI9341 LCD panel driver");
> +MODULE_LICENSE("GPL v2");
> --
> 2.7.4
_______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
