Hi
On 4/30/20 11:43 AM, dillon.minfei@xxxxxxxxx wrote:
From: dillon min <dillon.minfei@xxxxxxxxx>
Signed-off-by: dillon min <dillon.minfei@xxxxxxxxx>
Commit title should be ARM: dts: stm32: bla bla on stm32f429 and please
a commit message.
---
.../bindings/display/panel/ilitek,ili9341.txt | 42 +++++++++++
arch/arm/boot/dts/stm32f4-pinctrl.dtsi | 79 +++++++++++++++++++
arch/arm/boot/dts/stm32f429-disco.dts | 88 ++++++++++++++++++++++
arch/arm/boot/dts/stm32f429.dtsi | 12 +++
4 files changed, 221 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/ilitek,ili9341.txt
diff --git a/Documentation/devicetree/bindings/display/panel/ilitek,ili9341.txt b/Documentation/devicetree/bindings/display/panel/ilitek,ili9341.txt
This binding description should be in a separate patch and you have to
write in YAML format.
new file mode 100644
index 0000000..f5a4e55
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/ilitek,ili9341.txt
@@ -0,0 +1,42 @@
+Ilitek ILI9341 TFT panel driver with SPI control bus
+
+This is a driver for 240x320 TFT panels, accepting a rgb input
+streams that get adapted and scaled to the panel.
+
+Required properties:
+ - compatible: "stm32f429-disco,ltdc-panel", "ilitek,ili9341"
+ (full system-specific compatible is always required to look up configuration)
+ - reg: address of the panel on the SPI bus
+
+Optional properties:
+ - reset-gpios: a GPIO spec for the reset pin, see gpio/gpio.txt
+ - dc-gpios: a GPIO spec for the dc pin, see gpio/gpio.txt
+
+ The following optional properties only apply to RGB input mode:
+
+ - pixelclk-active: see display/panel/display-timing.txt
+ - de-active: see display/panel/display-timing.txt
+ - hsync-active: see display/panel/display-timing.txt
+ - vsync-active: see display/panel/display-timing.txt
+
+The panel must obey the rules for a SPI slave device as specified in
+spi/spi-bus.txt
+
+The device node can contain one 'port' child node with one child
+'endpoint' node, according to the bindings defined in
+media/video-interfaces.txt. This node should describe panel's video bus.
+
+Example:
+
+panel: display@0 {
+ compatible = "stm32f429-disco,ltdc-panel", "ilitek,ili9341";
+ reg = <0>;
+ spi-3wire;
+ spi-max-frequency = <10000000>;
+ dc-gpios = <&gpiod 13 0>;
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/stm32f4-pinctrl.dtsi b/arch/arm/boot/dts/stm32f4-pinctrl.dtsi
index 392fa14..45b68f4 100644
--- a/arch/arm/boot/dts/stm32f4-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32f4-pinctrl.dtsi
@@ -316,6 +316,85 @@
};
};
+ ltdc_pins_f429_disco: ltdc-1 {
+ pins {
+ pinmux = <STM32_PINMUX('C', 6, AF14)>,
+ /* LCD_HSYNC */
+ <STM32_PINMUX('A', 4, AF14)>,
+ /* LCD_VSYNC */
+ <STM32_PINMUX('G', 7, AF14)>,
+ /* LCD_CLK */
+ <STM32_PINMUX('C', 10, AF14)>,
+ /* LCD_R2 */
+ <STM32_PINMUX('B', 0, AF9)>,
+ /* LCD_R3 */
+ <STM32_PINMUX('A', 11, AF14)>,
+ /* LCD_R4 */
+ <STM32_PINMUX('A', 12, AF14)>,
+ /* LCD_R5 */
+ <STM32_PINMUX('B', 1, AF9)>,
+ /* LCD_R6*/
+ <STM32_PINMUX('G', 6, AF14)>,
+ /* LCD_R7 */
+ <STM32_PINMUX('A', 6, AF14)>,
+ /* LCD_G2 */
+ <STM32_PINMUX('G', 10, AF9)>,
+ /* LCD_G3 */
+ <STM32_PINMUX('B', 10, AF14)>,
+ /* LCD_G4 */
+ <STM32_PINMUX('D', 6, AF14)>,
+ /* LCD_B2 */
+ <STM32_PINMUX('G', 11, AF14)>,
+ /* LCD_B3*/
+ <STM32_PINMUX('B', 11, AF14)>,
+ /* LCD_G5 */
+ <STM32_PINMUX('C', 7, AF14)>,
+ /* LCD_G6 */
+ <STM32_PINMUX('D', 3, AF14)>,
+ /* LCD_G7 */
+ <STM32_PINMUX('G', 12, AF9)>,
+ /* LCD_B4 */
+ <STM32_PINMUX('A', 3, AF14)>,
+ /* LCD_B5 */
+ <STM32_PINMUX('B', 8, AF14)>,
+ /* LCD_B6 */
+ <STM32_PINMUX('B', 9, AF14)>,
+ /* LCD_B7 */
+ <STM32_PINMUX('F', 10, AF14)>;
+ /* LCD_DE */
+ slew-rate = <2>;
+ };
+ };
+
+ i2c3_pins: i2c3-0 {
+ pins {
+ pinmux = <STM32_PINMUX('C', 9, AF4)>,
+ /* I2C3_SDA */
+ <STM32_PINMUX('A', 8, AF4)>;
+ /* I2C3_SCL */
+ bias-disable;
+ drive-open-drain;
+ slew-rate = <3>;
+ };
+ };
+
+ spi5_pins: spi5-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('F', 7, AF5)>,
+ /* SPI5_CLK */
+ <STM32_PINMUX('F', 9, AF5)>;
+ /* SPI5_MOSI */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('F', 8, AF5)>;
+ /* SPI5_MISO */
+ bias-disable;
+ };
+ };
+
dcmi_pins: dcmi-0 {
pins {
pinmux = <STM32_PINMUX('A', 4, AF13)>, /* DCMI_HSYNC */
diff --git a/arch/arm/boot/dts/stm32f429-disco.dts b/arch/arm/boot/dts/stm32f429-disco.dts
index 30c0f67..55eed05 100644
--- a/arch/arm/boot/dts/stm32f429-disco.dts
+++ b/arch/arm/boot/dts/stm32f429-disco.dts
@@ -49,6 +49,8 @@
#include "stm32f429.dtsi"
#include "stm32f429-pinctrl.dtsi"
#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "STMicroelectronics STM32F429i-DISCO board";
@@ -98,6 +100,14 @@
regulator-name = "vcc5_host1";
regulator-always-on;
};
+
+ reg_3p3v: regulator-3p3v {
3p3 ?
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
};
&clk_hse {
@@ -127,3 +137,81 @@
pinctrl-names = "default";
status = "okay";
};
+
+<dc {
+ status = "okay";
+ pinctrl-0 = <<dc_pins_f429_disco>;
+ pinctrl-names = "default";
+
+ port {
+ ltdc_out_rgb: endpoint {
+ remote-endpoint = <&panel_in_rgb>;
+ };
+ };
+};
+
+&spi5 {
+ status = "okay";
+ pinctrl-0 = <&spi5_pins>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ cs-gpios = <&gpioc 1 GPIO_ACTIVE_LOW>,<&gpioc 2 GPIO_ACTIVE_LOW>;
+ dmas = <&dma2 3 2 0x400 0x0>,
+ <&dma2 4 2 0x400 0x0>;
+ dma-names = "rx", "tx";
+ l3gd20: l3gd20@0 {
+ compatible = "st,l3gd20-gyro";
+ spi-max-frequency = <10000000>;
+ st,drdy-int-pin = <2>;
+ interrupt-parent = <&gpioa>;
+ interrupts = <1 IRQ_TYPE_EDGE_RISING>,
+ <2 IRQ_TYPE_EDGE_RISING>;
+ reg = <0>;
+ vddio = <®_3p3v>;
+ vdd = <®_3p3v>;
+ status = "okay";
+ };
+ display: display@1{
+ /* Connect panel-ilitek-9341 to ltdc */
+ compatible = "stm32f429-disco,ltdc-panel", "ilitek,ili9341";
+ reg = <1>;
+ spi-3wire;
+ spi-max-frequency = <10000000>;
+ dc-gpios = <&gpiod 13 0>;
+ port {
+ panel_in_rgb: endpoint {
+ remote-endpoint = <<dc_out_rgb>;
+ };
+ };
+ };
+};
+
+&i2c3 {
Nodes are have to be ordered
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3_pins>;
+ status = "okay";
+
+ touch: stmpe811@41 {
+ compatible = "st,stmpe811";
+ reg = <0x41>;
+ interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-parent = <&gpioa>;
+ vio = <®_3p3v>;
+ vcc = <®_3p3v>;
+ status = "okay";
+
+ stmpe_touchscreen {
+ compatible = "st,stmpe-ts";
+ st,sample-time = <4>;
+ st,mod-12b = <1>;
+ st,ref-sel = <0>;
+ st,adc-freq = <1>;
+ st,ave-ctrl = <1>;
+ st,touch-det-delay = <2>;
+ st,settling = <2>;
+ st,fraction-z = <7>;
+ st,i-drive = <1>;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/stm32f429.dtsi b/arch/arm/boot/dts/stm32f429.dtsi
index d777069..257b843 100644
--- a/arch/arm/boot/dts/stm32f429.dtsi
+++ b/arch/arm/boot/dts/stm32f429.dtsi
@@ -402,6 +402,18 @@
Split Soc updates in a separate patch
status = "disabled";
};
+ i2c3: i2c@40005c00 {
+ compatible = "st,stm32f4-i2c";
+ reg = <0x40005c00 0x400>;
+ interrupts = <72>,
+ <73>;
+ resets = <&rcc STM32F4_APB1_RESET(I2C3)>;
+ clocks = <&rcc 0 STM32F4_APB1_CLOCK(I2C3)>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
dac: dac@40007400 {
compatible = "st,stm32f4-dac-core";
reg = <0x40007400 0x400>;
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
