On Tue, Mar 31, 2020 at 1:14 PM Sam Ravnborg <sam@xxxxxxxxxxxx> wrote: > > Hi Rob. > > On Tue, Mar 31, 2020 at 11:20:13AM -0600, Rob Herring wrote: > > On Sun, Mar 29, 2020 at 1:04 PM Sam Ravnborg <sam@xxxxxxxxxxxx> wrote: > > > > > > Hi Rob. > > > > > > > > + > > > > > + mode-gpios: > > > > > + description: | > > > > > + GPIO ordered MO, LR, and UD as specified in LS037V7DW01.pdf > > > > > > > > 3 or... > > > > > > > > > + change configuration between QVGA and VGA mode and the > > > > > + scan direction. As these pins can be also configured > > > > > + with external pulls, all the GPIOs are considered > > > > > + optional with holes in the array. > > > > > > > > minItems: 3 > > > > maxItems: 5 > > > > > > This binding can specify up to three GPIOs like this: > > > > So it should be: > > > > minItems: 1 > > maxItems: 3 > > > > > > > + mode-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH /* gpio154, lcd MO */ > > > > > + &gpio1 2 GPIO_ACTIVE_HIGH /* gpio2, lcd LR */ > > > > > + &gpio1 3 GPIO_ACTIVE_HIGH>; /* gpio3, lcd UD */ > > > > > > They are in the linux kernel driver accessed like this: > > > > > > devm_gpiod_get_index(&pdev->dev, "mode", 2, GPIOD_OUT_LOW); > > > > > > The following is OK in the DT file: > > > > > > mode-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>; > > > > > > mode-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH > > > &gpio1 2 GPIO_ACTIVE_HIGH>; > > > > > > mode-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH > > > &gpio1 2 GPIO_ACTIVE_HIGH > > > &gpio1 3 GPIO_ACTIVE_HIGH>; > > > > With the above, the 2nd 2 should fail... > > > > > But the following is not OK: > > > mode-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>, <&gpio1 2 GPIO_ACTIVE_HIGH>; > > > > And this should pass. We want phandle+arg type properties to be > > bracketed like this. > > OK, so if I get you right you say that we should accept the: > <phandle+arg>, <phandle+arg> ... syntax. > > And then ignore that current DT files uses: > <phandle+arg phandle+arg> > > > A binding like this: > mode-gpios: > minItems: 1 > maxItems: 3 > description: | > GPIO ordered MO, LR, and UD as specified in LS037V7DW01.pdf > This panel can have zero to three GPIOs to configure to > > > Do not error out when the example looks like this: > > mode-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH /* gpio154, lcd MO */ > &gpio1 2 GPIO_ACTIVE_HIGH /* gpio2, lcd LR */ > &gpio1 3 GPIO_ACTIVE_HIGH>; /* gpio3, lcd UD */ That's because we can't distinguish between this and 1 entry as the schema doesn't have visibility of what #gpio-cells value is. dtc does check that the cell sizes are correct. We'll need to somehow combine that and the schema to check this form correctly. > > So if I get you right this is a bug in the tooling. Limitation I guess. I thought you where saying the bracketed form was not working. Rob _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
