Hi Vinay.
On Tue, Mar 17, 2020 at 12:25:42PM +0530, Vinay Simha B N wrote:
> sam,
>
> i need some inputs on the below error. I had created this file
> Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml
> by using vim editor. Do we have any tool to create yaml file?
I use vim myself, but is careful to follow the right syntax.
>
> i do not get the error when running 'make dt_binding_check' in my
> build environment
> Documentation/devicetree/bindings/display/bridge/toshiba-tc358775.yaml
>
> is there any tool available similar to scripts/checkpatch.pl -f
> <file> , for yaml files?
Please read Documentation/devicetree/writing-schema.
Here you can find general info + instruction how to install the tools
required for "make dt_binding_check".
I could reproduce the error reported by Rob.
I gave your binding file a shot - there were a lot of smaller issues:
- do not use tabs in yaml files
- be consistent in indent
- vendor prefixed properties needed some extra care
- example was full of bugs
- "..."
- no need for status = "okay";
- properties spelled wrong
For the example I adjusted it to use indent of 4 spaces, which IMO
is more readable than the two spaces used in the other parts of the
file.
I have attached the updated binding file - please review and fix.
This is just a quick shot, I did not do a proper review.
Please rename the file, other files in same dir are named "toshiba,xxx",
so replace '-' with ','.
And try to introduce bugs in the example - and check that the tooling
catches the bug.
hint:
make DT=.../foo.yaml dt_binding_check
is a qucik way to check only your binding.
And for new bindings the preferred license is: (GPL-2.0-only OR BSD-2-Clause)
Sam
# SPDX-License-Identifier: GPL-2.0
%YAML 1.2
---
$id: http://devicetree.org/schemas/display/bridge/toshiba-tc358775.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Toshiba TC358775 DSI to LVDS bridge bindings
maintainers:
- Vinay Simha BN <simhavcs@xxxxxxxxx>
description: |
This binding supports DSI to LVDS bridge TC358775
properties:
compatible:
const: toshiba,tc358775
reg:
maxItems: 1
description: i2c address of the bridge, 0x0f
toshiba,dsi-lanes:
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32
- minimum: 1
maximum: 4
default: 1
description: bla bla
toshiba,dual-link:
$ref: /schemas/types.yaml#definitions/flag
description: bla bla
vdd-supply:
maxItems: 1
description: 1.2V LVDS Power Supply
vddio-supply:
maxItems: 1
description: 1.8V IO Power Supply
stby-gpios:
maxItems: 1
description: Standby pin, Low active
reset-gpios:
maxItems: 1
description: Hardware reset, Low active
ports:
type: object
properties:
port@0:
type: object
description: |
DSI Input. The remote endpoint phandle should be a
reference to a valid mipi_dsi_host device node.
port@1:
type: object
description: |
Video port for LVDS output (panel or connector).
required:
- port@0
- port@1
required:
- compatible
- reg
- tc,dsi-lanes
- vdd-supply
- vddio-supply
- stby-gpios
- reset-gpios
- ports
examples:
- |+
#include <dt-bindings/gpio/gpio.h>
i2c@78b8000 {
#address-cells = <1>;
#size-cells = <0>;
/* On High speed expansion */
label = "HS-I2C2";
status = "okay";
tc_bridge: bridge@f {
compatible = "toshiba,tc358775";
reg = <0x0f>;
tc,dsi-lanes = <4>;
tc,dual-link = <0>;
vdd-supply = <&pm8916_l2>;
vddio-supply = <&pm8916_l6>;
stby-gpios = <&msmgpio 99 GPIO_ACTIVE_LOW>;
reset-gpios = <&msmgpio 72 GPIO_ACTIVE_LOW>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
d2l_in: endpoint {
remote-endpoint = <&dsi0_out>;
};
};
port@1 {
reg = <1>;
d2l_out: endpoint {
remote-endpoint = <&panel_in>;
};
};
};
};
};
panel: auo,b101xtn01 {
status = "okay";
compatible = "auo,b101xtn01", "panel-lvds";
power-supply = <&pm8916_l14>;
width-mm = <223>;
height-mm = <125>;
data-mapping = "jeida-24";
panel-timing {
/* 1366x768 @60Hz */
clock-frequency = <72000000>;
hactive = <1366>;
vactive = <768>;
hsync-len = <70>;
hfront-porch = <20>;
hback-porch = <0>;
vsync-len = <42>;
vfront-porch = <14>;
vback-porch = <0>;
};
port {
panel_in: endpoint {
remote-endpoint = <&d2l_out>;
};
};
};
mdss {
dsi@1a98000 {
ports {
port@1 {
dsi0_out: endpoint {
remote-endpoint = <&d2l_in>;
data-lanes = <0 1 2 3>;
};
};
};
};
};
...
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
