Hi Ville,
> Am 02.03.2020 um 21:34 schrieb Ville Syrjala <ville.syrjala@xxxxxxxxxxxxxxx>:
>
> From: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
>
> The currently listed dotclock disagrees with the currently
> listed vrefresh rate. Change the dotclock to match the vrefresh.
>
> Someone tell me which (if either) of the dotclock or vreresh is
> correct?
Data sheet of COM37H3M99DTC says:
MIN TYP MAX
CLK frequency fCLK 18 19.8 27 MHz
VSYNC Frequency fVSYNC 54 60 66 Hz
VSYNC cycle time tv 646 650 700 H
HSYNC frequency fHSYNC -- 39.0 50.0 Khz
HSYNC cycle time th 504 508 630 CLK
But data sheet of COM37H3M05DTC says
MIN TYP MAX
CLK frequency fCLK -- 22.4 26.3 MHz (in VGA mode - there is also an QVGA mode)
VSYNC Frequency fVSYNC 54 60 66 Hz
VSYNC cycle time tv -- 650 -- H
HSYNC frequency fHSYNC -- 39.3 -- Khz
HSYNC cycle time th -- 570 -- CLK
So there are two different subvariants of the same panel.
If I remember correctly, the 05 is older (April 2010)
and the 99DTC newer (Dec 2011).
So 22 MHz isn't outside of either spec but may be higher
than needed for the 99DTC. I.e. the panel is probably
running at higher frame rate than 60 fps.
Hm. I think we should define some compromise. I.e.
.clock = 22230
.vrefresh = 60
.vtotal = 650
.htotal = 570
Probably we originally tried to do this with the parameter
set but got something wrong.
If you agree with this approach, I can try to figure out
the other parameters so that they should fit both panel
variants. I can only test with COM37H3M99DTC since I
do no longer have a device with COM37H3M05DTC.
In general it seems that the structure drm_display_mode
is overdetermined.
Either .clock could be calculated from .vrefresh (and
the other .vtotal and .htotal) or vice versa like I
did for the proposal above.
I haven't looked into the driver code, but would it be
possible to specify .clock = 0 (or leave it out) to
calculate it bottom up? This would avoid such inconsistencies.
On the other hand it is not easily visible any more
from the code if the clock is in range of the data
sheet limits.
BR and thanks,
Nikolaus
>
> Cc: H. Nikolaus Schaller <hns@xxxxxxxxxxxxx>
> Cc: Sam Ravnborg <sam@xxxxxxxxxxxx>
> Signed-off-by: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
> ---
> drivers/gpu/drm/panel/panel-simple.c | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
> index ca72b73408e9..f9b4f84bffb3 100644
> --- a/drivers/gpu/drm/panel/panel-simple.c
> +++ b/drivers/gpu/drm/panel/panel-simple.c
> @@ -2617,7 +2617,7 @@ static const struct panel_desc ontat_yx700wv03 = {
> };
>
> static const struct drm_display_mode ortustech_com37h3m_mode = {
> - .clock = 22153,
> + .clock = 19842,
> .hdisplay = 480,
> .hsync_start = 480 + 8,
> .hsync_end = 480 + 8 + 10,
> --
> 2.24.1
>
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
