Hi, Jitao:
On Tue, 2020-02-25 at 14:46 +0800, Jitao Shi wrote:
> Add decriptions about supported chips, including MT2701 & MT8173 &
> mt8183
descriptions
>
> 1. Add more chips support. ex. MT2701 & MT8173 & MT8183
> 2. Add property "pinctrl-names" to swap pin mode between gpio and dpi mode. Set
> pin mode to gpio oupput-low to avoid leakage current when dpi disable.
> 3. Add property "pclk-sample" to config the dpi sample on falling (0),
> rising (1), both falling and rising (2).
The title is just about supported chips, so I prefer you move other
modification to another patch. Of course, you could use a more rough
title to include all what you do so you need not to break this patch.
>
> Signed-off-by: Jitao Shi <jitao.shi@xxxxxxxxxxxx>
> ---
> .../bindings/display/mediatek/mediatek,dpi.txt | 10 ++++++++++
> 1 file changed, 10 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> index b6a7e7397b8b..0dee4f7a227e 100644
> --- a/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dpi.txt
> @@ -7,6 +7,7 @@ output bus.
>
> Required properties:
> - compatible: "mediatek,<chip>-dpi"
> + the supported chips are mt2701 , mt8173 and mt8183.
> - reg: Physical base address and length of the controller's registers
> - interrupts: The interrupt signal from the function block.
> - clocks: device clocks
> @@ -16,6 +17,11 @@ Required properties:
> Documentation/devicetree/bindings/graph.txt. This port should be connected
> to the input port of an attached HDMI or LVDS encoder chip.
>
> +Optional properties:
> +- pinctrl-names: Contain "gpiomode" and "dpimode".
> +- pclk-sample: 0: sample in falling edge, 1: sample in rising edge, 2: sample
> + in both falling and rising edge.
pinctrl-names & pclk-sample are defined in another document, please list
the reference document, [1] is the sample. For pclk-sample, I think you
should modify [2] to add 'sampling in both failing and rising edge'.
[1] Documentation/devicetree/bindings/display/bridge/ti,tfp410.txt
[2] Documentation/devicetree/bindings/media/video-interfaces.txt
> +
> Example:
>
> dpi0: dpi@1401d000 {
> @@ -26,6 +32,10 @@ dpi0: dpi@1401d000 {
> <&mmsys CLK_MM_DPI_ENGINE>,
> <&apmixedsys CLK_APMIXED_TVDPLL>;
> clock-names = "pixel", "engine", "pll";
> + pclk-sample = 0;
I think you should move pclk-sample into the port node according to [2].
Regards,
CK
> + pinctrl-names = "gpiomode", "dpimode";
> + pinctrl-0 = <&dpi_pin_gpio>;
> + pinctrl-1 = <&dpi_pin_func>;
>
> port {
> dpi0_out: endpoint {
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
