Re: Linux 3.2: After resume screen only turned on after switching terminals

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Am Freitag, den 06.07.2012, 17:34 +0200 schrieb Paul Menzel:
> Am Donnerstag, den 05.07.2012, 08:58 -0400 schrieb Alex Deucher:
> > On Wed, Jul 4, 2012 at 10:11 AM, Paul Menzel wrote:
> > > Am Mittwoch, den 04.07.2012, 09:55 -0400 schrieb Alex Deucher:
> > >> On Wed, Jul 4, 2012 at 9:41 AM, Paul Menzel wrote:
> > >> > Am Samstag, den 30.06.2012, 21:00 +0200 schrieb Paul Menzel:
> > >> >> Am Dienstag, den 26.06.2012, 07:42 +0200 schrieb Michel Dänzer:
> > >> >> > On Mon, 2012-06-25 at 21:14 +0200, Paul Menzel wrote:
> > >> >> > >
> > >> >> > > resuming from suspend to RAM the monitor was indicating by a blinking
> > >> >> > > LED that it did not receive any signal. This is the first time this
> > >> >> > > happened. Resuming from suspend to RAM had worked without problems
> > >> >> > > before (and probably will work again the next tries).
> > >> >> > >
> > >> >> > > Logging in from SSH worked fine though. Switching terminal to tty1
> > >> >> > > nothing changed but going back to tty7, where X was supposed to run),
> > >> >> > > and the monitor detected a signal and showed the screensaver.
> > >> >> > >
> > >> >> > > Switching to tty1 still does not work though, that means the monitor
> > >> >> > > indicates that it gets no signal.
> > >> >> >
> > >> >> > What about tty2-6 or any others?
> > >> >>
> > >> >> It just happened again. tty2–6 also do not show anything.
> > >> >>
> > >> >> > What does fbset -i say when the problem occurs?
> > >> >>
> > >> >> I logged in over SSH not having switched the ttys yet. This is the
> > >> >> result.
> > >> >>
> > >> >>         $ fbset -i
> > >> >>
> > >> >>         mode "1280x1024"
> > >> >>             geometry 1280 1024 1280 1024 32
> > >> >>             timings 0 0 0 0 0 0 0
> > >> >>             accel true
> > >> >>             rgba 8/16,8/8,8/0,0/0
> > >> >>         endmode
> > >> >>
> > >> >>         Frame buffer device information:
> > >> >>             Name        : radeondrmfb
> > >> >>             Address     : 0xd0142000
> > >> >>             Size        : 5242880
> > >> >>             Type        : PACKED PIXELS
> > >> >>             Visual      : TRUECOLOR
> > >> >>             XPanStep    : 1
> > >> >>             YPanStep    : 1
> > >> >>             YWrapStep   : 0
> > >> >>             LineLength  : 5120
> > >> >>             Accelerator : No
> > >> >>
> > >> >> This does not differ though after having switched between ttys and
> > >> >> getting a working X server again. The other ttys do not just show black.
> > >> >> When switching from tty7 with the X server running to a console(?) tty
> > >> >> then I shortly (half second) see some kind of test image, which contains
> > >> >> four horizontal colored stripes red, green, blue and white(?).
> > >> >>
> > >> >> I could not find anything in the output of `dmesg`, but
> > >> >> `/var/log/syslog` contains several of the following lines.
> > >> >>
> > >> >>         Jun 29 19:44:57 debian-host acpid: client 8677[0:0] has disconnected
> > >> >>         Jun 29 19:45:08 debian-host acpid: client connected from 8677[0:0]
> > >> >>         Jun 29 19:45:08 debian-host acpid: 1 client rule loaded
> > >> >
> > >> > Does someone have an idea what the problem might be and how to fix it?
> > >>
> > >> Is this a regression?  If so can you bisect?
> > >
> > > I do not think so. But the problem is I just got that board, have only
> > > used it with Linux 3.2.x (from Debian Sid/unstable) and this issue is
> > > not reproducible, that means, it happens in less then 5(?) percent of
> > > the suspend and resume cycles.
> > >
> > > Any idea what these acpid messages could mean?
> 
> It just happened again. This time with the monitor not getting any
> signal. Switching to other virtual terminals does not work.
> 
> What debug levels should I increase?

I attach the output of `dmesg`.


Thanks,

Paul
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.2.0-3-686-pae (Debian 3.2.21-3) (debian-kernel@xxxxxxxxxxxxxxxx) (gcc version 4.6.3 (Debian 4.6.3-8) ) #1 SMP Thu Jun 28 08:56:46 UTC 2012
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e6000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 00000000cfeb0000 (usable)
[    0.000000]  BIOS-e820: 00000000cfeb0000 - 00000000cfec0000 (ACPI data)
[    0.000000]  BIOS-e820: 00000000cfec0000 - 00000000cfef0000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000cfef0000 - 00000000cff00000 (reserved)
[    0.000000]  BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[    0.000000]  BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] DMI present.
[    0.000000] DMI: To Be Filled By O.E.M. To Be Filled By O.E.M./A780FullHD, BIOS P1.00 08/01/2008
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] last_pfn = 0x120000 max_arch_pfn = 0x1000000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-EFFFF uncachable
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 0000000000 mask FF80000000 write-back
[    0.000000]   1 base 0080000000 mask FFC0000000 write-back
[    0.000000]   2 base 00C0000000 mask FFF0000000 write-back
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] TOM2: 0000000130000000 aka 4864M
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] e820 update range: 00000000d0000000 - 0000000100000000 (usable) ==> (reserved)
[    0.000000] found SMP MP-table at [c00ff780] ff780
[    0.000000] initial memory mapped : 0 - 01a00000
[    0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[    0.000000] init_memory_mapping: 0000000000000000-00000000379fe000
[    0.000000]  0000000000 - 0000200000 page 4k
[    0.000000]  0000200000 - 0037800000 page 2M
[    0.000000]  0037800000 - 00379fe000 page 4k
[    0.000000] kernel direct mapping tables up to 379fe000 @ 19fa000-1a00000
[    0.000000] RAMDISK: 368be000 - 37457000
[    0.000000] ACPI: RSDP 000fa160 00014 (v00 ACPIAM)
[    0.000000] ACPI: RSDT cfeb0000 00038 (v01 080108 RSDT2148 20080801 MSFT 00000097)
[    0.000000] ACPI: FACP cfeb0200 00084 (v02 A M I  OEMFACP  12000601 MSFT 00000097)
[    0.000000] ACPI: DSDT cfeb0440 07737 (v01  AS146 AS146012 00000012 INTL 20051117)
[    0.000000] ACPI: FACS cfec0000 00040
[    0.000000] ACPI: APIC cfeb0390 0006C (v01 080108 APIC2148 20080801 MSFT 00000097)
[    0.000000] ACPI: MCFG cfeb0400 0003C (v01 080108 OEMMCFG  20080801 MSFT 00000097)
[    0.000000] ACPI: OEMB cfec0040 00071 (v01 080108 OEMB2148 20080801 MSFT 00000097)
[    0.000000] ACPI: SSDT cfeb7b80 0028A (v01 A M I  POWERNOW 00000001 AMD  00000001)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 3718MB HIGHMEM available.
[    0.000000] 889MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 379fe000
[    0.000000]   low ram: 0 - 379fe000
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x000379fe
[    0.000000]   HighMem  0x000379fe -> 0x00120000
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[3] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x000cfeb0
[    0.000000]     0: 0x00100000 -> 0x00120000
[    0.000000] On node 0 totalpages: 982591
[    0.000000] free_area_init_node: node 0, pgdat c140d640, node_mem_map f44be200
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3951 pages, LIFO batch:0
[    0.000000]   Normal zone: 1748 pages used for memmap
[    0.000000]   Normal zone: 221994 pages, LIFO batch:31
[    0.000000]   HighMem zone: 7437 pages used for memmap
[    0.000000]   HighMem zone: 747429 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] Detected use of extended apic ids on hypertransport bus
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[    0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e6000
[    0.000000] PM: Registered nosave memory: 00000000000e6000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at cff00000 (gap: cff00000:30000000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] setup_percpu: NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:4 nr_node_ids:1
[    0.000000] PERCPU: Embedded 14 pages/cpu @f79b3000 s33280 r0 d24064 u57344
[    0.000000] pcpu-alloc: s33280 r0 d24064 u57344 alloc=14*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 973374
[    0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-3.2.0-3-686-pae root=/dev/mapper/speicher-root ro quiet
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Initializing CPU#0
[    0.000000] Initializing HighMem for node 0 (000379fe:00120000)
[    0.000000] Memory: 3875320k/4718592k available (2836k kernel code, 55044k reserved, 1343k data, 412k init, 3019464k highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xffd36000 - 0xfffff000   (2852 kB)
[    0.000000]     pkmap   : 0xffa00000 - 0xffc00000   (2048 kB)
[    0.000000]     vmalloc : 0xf81fe000 - 0xff9fe000   ( 120 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf79fe000   ( 889 MB)
[    0.000000]       .init : 0xc1415000 - 0xc147c000   ( 412 kB)
[    0.000000]       .data : 0xc12c50ec - 0xc1414f00   (1343 kB)
[    0.000000]       .text : 0xc1000000 - 0xc12c50ec   (2836 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] Hierarchical RCU implementation.
[    0.000000] 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.000000] NR_IRQS:2304 nr_irqs:712 16
[    0.000000] CPU 0 irqstacks, hard=f4006000 soft=f4008000
[    0.000000] spurious 8259A interrupt: IRQ7.
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] Fast TSC calibration using PIT
[    0.000000] Detected 2494.485 MHz processor.
[    0.000000] Marking TSC unstable due to TSCs unsynchronized
[    0.004006] Calibrating delay loop (skipped), value calculated using timer frequency.. 4988.97 BogoMIPS (lpj=9977940)
[    0.004011] pid_max: default: 32768 minimum: 301
[    0.004066] Security Framework initialized
[    0.004074] AppArmor: AppArmor disabled by boot time parameter
[    0.004096] Mount-cache hash table entries: 512
[    0.004257] Initializing cgroup subsys cpuacct
[    0.004263] Initializing cgroup subsys memory
[    0.004274] Initializing cgroup subsys devices
[    0.004277] Initializing cgroup subsys freezer
[    0.004280] Initializing cgroup subsys net_cls
[    0.004283] Initializing cgroup subsys blkio
[    0.004291] Initializing cgroup subsys perf_event
[    0.004325] CPU: Physical Processor ID: 0
[    0.004327] CPU: Processor Core ID: 0
[    0.004330] mce: CPU supports 5 MCE banks
[    0.004342] using AMD E400 aware idle routine
[    0.008079] ACPI: Core revision 20110623
[    0.011129] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.011506] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.051199] CPU0: AMD Athlon(tm) Dual Core Processor 4850e stepping 02
[    0.052002] Performance Events: AMD PMU driver.
[    0.052002] ... version:                0
[    0.052002] ... bit width:              48
[    0.052002] ... generic registers:      4
[    0.052002] ... value mask:             0000ffffffffffff
[    0.052002] ... max period:             00007fffffffffff
[    0.052002] ... fixed-purpose events:   0
[    0.052002] ... event mask:             000000000000000f
[    0.052002] NMI watchdog enabled, takes one hw-pmu counter.
[    0.052002] CPU 1 irqstacks, hard=f4094000 soft=f4096000
[    0.052002] Booting Node   0, Processors  #1
[    0.052002] smpboot cpu 1: start_ip = 9b000
[    0.008000] Initializing CPU#1
[    0.136100] NMI watchdog enabled, takes one hw-pmu counter.
[    0.136122] Brought up 2 CPUs
[    0.136125] Total of 2 processors activated (9978.46 BogoMIPS).
[    0.136786] devtmpfs: initialized
[    0.136786] PM: Registering ACPI NVS region at cfec0000 (196608 bytes)
[    0.136786] print_constraints: dummy: 
[    0.136786] NET: Registered protocol family 16
[    0.136786] node 0 link 0: io port [1000, ffffff]
[    0.136786] TOM: 00000000d0000000 aka 3328M
[    0.136786] node 0 link 0: mmio [a0000, bffff]
[    0.136786] node 0 link 0: mmio [d0000000, efffffff]
[    0.136786] node 0 link 0: mmio [f0000000, fddfffff]
[    0.136786] node 0 link 0: mmio [fde00000, fdefffff]
[    0.136786] node 0 link 0: mmio [fdf00000, ffefffff]
[    0.136786] TOM2: 0000000130000000 aka 4864M
[    0.136786] bus: [00, 07] on node 0 link 0
[    0.136786] bus: 00 index 0 [io  0x0000-0xffff]
[    0.136786] bus: 00 index 1 [mem 0x000a0000-0x000bffff]
[    0.136786] bus: 00 index 2 [mem 0xd0000000-0xffffffff]
[    0.136786] bus: 00 index 3 [mem 0x130000000-0xfcffffffff]
[    0.136786] ACPI: bus type pci registered
[    0.136786] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.136786] PCI: not using MMCONFIG
[    0.137208] PCI : PCI BIOS aera is rw and x. Use pci=nobios if you want it NX.
[    0.137284] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
[    0.137286] PCI: Using configuration type 1 for base access
[    0.137872] bio: create slab <bio-0> at 0
[    0.137872] ACPI: Added _OSI(Module Device)
[    0.137872] ACPI: Added _OSI(Processor Device)
[    0.137872] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.137872] ACPI: Added _OSI(Processor Aggregator Device)
[    0.137872] ACPI: EC: Look up EC in DSDT
[    0.140986] ACPI: Executed 4 blocks of module-level executable AML code
[    0.156263] ACPI: Interpreter enabled
[    0.156272] ACPI: (supports S0 S1 S3 S4 S5)
[    0.156295] ACPI: Using IOAPIC for interrupt routing
[    0.156317] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.157004] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[    0.157006] PCI: Using MMCONFIG for extended config space
[    0.161332] ACPI: No dock devices found.
[    0.161335] HEST: Table not found.
[    0.161340] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.161522] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.161703] pci_root PNP0A03:00: host bridge window [io  0x0000-0x0cf7]
[    0.161706] pci_root PNP0A03:00: host bridge window [io  0x0d00-0xffff]
[    0.161709] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
[    0.161712] pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff]
[    0.161714] pci_root PNP0A03:00: host bridge window [mem 0xcff00000-0xdfffffff]
[    0.161717] pci_root PNP0A03:00: host bridge window [mem 0xf0000000-0xfebfffff]
[    0.161723] pci_root PNP0A03:00: ignoring host bridge window [mem 0x000d0000-0x000dffff] (conflicts with Adapter ROM [mem 0x000cf000-0x000d0bff])
[    0.161742] pci 0000:00:00.0: [1022:9600] type 0 class 0x000600
[    0.161805] pci 0000:00:01.0: [1849:9602] type 1 class 0x000604
[    0.161856] pci 0000:00:09.0: [1022:9608] type 1 class 0x000604
[    0.161897] pci 0000:00:09.0: PME# supported from D0 D3hot D3cold
[    0.161901] pci 0000:00:09.0: PME# disabled
[    0.161918] pci 0000:00:0a.0: [1022:9609] type 1 class 0x000604
[    0.161957] pci 0000:00:0a.0: PME# supported from D0 D3hot D3cold
[    0.161960] pci 0000:00:0a.0: PME# disabled
[    0.161990] pci 0000:00:11.0: [1002:4391] type 0 class 0x000106
[    0.162011] pci 0000:00:11.0: reg 10: [io  0xb000-0xb007]
[    0.162022] pci 0000:00:11.0: reg 14: [io  0xa000-0xa003]
[    0.162033] pci 0000:00:11.0: reg 18: [io  0x9000-0x9007]
[    0.162043] pci 0000:00:11.0: reg 1c: [io  0x8000-0x8003]
[    0.162054] pci 0000:00:11.0: reg 20: [io  0x7000-0x700f]
[    0.162065] pci 0000:00:11.0: reg 24: [mem 0xfddff800-0xfddffbff]
[    0.162128] pci 0000:00:12.0: [1002:4397] type 0 class 0x000c03
[    0.162143] pci 0000:00:12.0: reg 10: [mem 0xfddfe000-0xfddfefff]
[    0.162215] pci 0000:00:12.1: [1002:4398] type 0 class 0x000c03
[    0.162230] pci 0000:00:12.1: reg 10: [mem 0xfddfd000-0xfddfdfff]
[    0.162308] pci 0000:00:12.2: [1002:4396] type 0 class 0x000c03
[    0.162329] pci 0000:00:12.2: reg 10: [mem 0xfddff000-0xfddff0ff]
[    0.162419] pci 0000:00:12.2: supports D1 D2
[    0.162421] pci 0000:00:12.2: PME# supported from D0 D1 D2 D3hot
[    0.162426] pci 0000:00:12.2: PME# disabled
[    0.162452] pci 0000:00:13.0: [1002:4397] type 0 class 0x000c03
[    0.162467] pci 0000:00:13.0: reg 10: [mem 0xfddfc000-0xfddfcfff]
[    0.162539] pci 0000:00:13.1: [1002:4398] type 0 class 0x000c03
[    0.162553] pci 0000:00:13.1: reg 10: [mem 0xfddf7000-0xfddf7fff]
[    0.162632] pci 0000:00:13.2: [1002:4396] type 0 class 0x000c03
[    0.162653] pci 0000:00:13.2: reg 10: [mem 0xfddf6800-0xfddf68ff]
[    0.162742] pci 0000:00:13.2: supports D1 D2
[    0.162744] pci 0000:00:13.2: PME# supported from D0 D1 D2 D3hot
[    0.162748] pci 0000:00:13.2: PME# disabled
[    0.162775] pci 0000:00:14.0: [1002:4385] type 0 class 0x000c05
[    0.162886] pci 0000:00:14.1: [1002:439c] type 0 class 0x000101
[    0.162904] pci 0000:00:14.1: reg 10: [io  0x0000-0x0007]
[    0.162914] pci 0000:00:14.1: reg 14: [io  0x0000-0x0003]
[    0.162925] pci 0000:00:14.1: reg 18: [io  0x0000-0x0007]
[    0.162935] pci 0000:00:14.1: reg 1c: [io  0x0000-0x0003]
[    0.162946] pci 0000:00:14.1: reg 20: [io  0xff00-0xff0f]
[    0.163010] pci 0000:00:14.2: [1002:4383] type 0 class 0x000403
[    0.163034] pci 0000:00:14.2: reg 10: [mem 0xfddf0000-0xfddf3fff 64bit]
[    0.163106] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
[    0.163110] pci 0000:00:14.2: PME# disabled
[    0.163126] pci 0000:00:14.3: [1002:439d] type 0 class 0x000601
[    0.163210] pci 0000:00:14.4: [1002:4384] type 1 class 0x000604
[    0.163260] pci 0000:00:14.5: [1002:4399] type 0 class 0x000c03
[    0.163275] pci 0000:00:14.5: reg 10: [mem 0xfddf5000-0xfddf5fff]
[    0.163349] pci 0000:00:18.0: [1022:1100] type 0 class 0x000600
[    0.163369] pci 0000:00:18.1: [1022:1101] type 0 class 0x000600
[    0.163384] pci 0000:00:18.2: [1022:1102] type 0 class 0x000600
[    0.163400] pci 0000:00:18.3: [1022:1103] type 0 class 0x000600
[    0.163452] pci 0000:01:05.0: [1002:9610] type 0 class 0x000300
[    0.163462] pci 0000:01:05.0: reg 10: [mem 0xd0000000-0xdfffffff pref]
[    0.163467] pci 0000:01:05.0: reg 14: [io  0xc000-0xc0ff]
[    0.163472] pci 0000:01:05.0: reg 18: [mem 0xfdff0000-0xfdffffff]
[    0.163484] pci 0000:01:05.0: reg 24: [mem 0xfde00000-0xfdefffff]
[    0.163503] pci 0000:01:05.0: supports D1 D2
[    0.163544] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.163548] pci 0000:00:01.0:   bridge window [io  0xc000-0xcfff]
[    0.163551] pci 0000:00:01.0:   bridge window [mem 0xfde00000-0xfdffffff]
[    0.163556] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.163584] pci 0000:00:09.0: PCI bridge to [bus 02-03]
[    0.163588] pci 0000:00:09.0:   bridge window [io  0xd000-0xdfff]
[    0.163592] pci 0000:00:09.0:   bridge window [mem 0xfe000000-0xfeafffff]
[    0.163596] pci 0000:00:09.0:   bridge window [mem 0xfa000000-0xfcefffff 64bit pref]
[    0.163638] pci 0000:04:00.0: [10ec:8168] type 0 class 0x000200
[    0.163652] pci 0000:04:00.0: reg 10: [io  0xe800-0xe8ff]
[    0.163675] pci 0000:04:00.0: reg 18: [mem 0xfcfff000-0xfcffffff 64bit pref]
[    0.163690] pci 0000:04:00.0: reg 20: [mem 0xfcfe0000-0xfcfeffff 64bit pref]
[    0.163700] pci 0000:04:00.0: reg 30: [mem 0xfebf0000-0xfebfffff pref]
[    0.163750] pci 0000:04:00.0: supports D1 D2
[    0.163752] pci 0000:04:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.163757] pci 0000:04:00.0: PME# disabled
[    0.168025] pci 0000:00:0a.0: PCI bridge to [bus 04-04]
[    0.168029] pci 0000:00:0a.0:   bridge window [io  0xe000-0xefff]
[    0.168032] pci 0000:00:0a.0:   bridge window [mem 0xfeb00000-0xfebfffff]
[    0.168037] pci 0000:00:0a.0:   bridge window [mem 0xfcf00000-0xfcffffff 64bit pref]
[    0.168100] pci 0000:00:14.4: PCI bridge to [bus 05-05] (subtractive decode)
[    0.168110] pci 0000:00:14.4:   bridge window [io  0x0000-0x0cf7] (subtractive decode)
[    0.168113] pci 0000:00:14.4:   bridge window [io  0x0d00-0xffff] (subtractive decode)
[    0.168116] pci 0000:00:14.4:   bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[    0.168119] pci 0000:00:14.4:   bridge window [mem 0xcff00000-0xdfffffff] (subtractive decode)
[    0.168122] pci 0000:00:14.4:   bridge window [mem 0xf0000000-0xfebfffff] (subtractive decode)
[    0.168136] pci_bus 0000:00: on NUMA node 0
[    0.168139] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.168354] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[    0.168398] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCEA._PRT]
[    0.168440] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PC._PRT]
[    0.168505] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE9._PRT]
[    0.168636]  pci0000:00: Requesting ACPI _OSC control (0x1d)
[    0.168921]  pci0000:00: ACPI _OSC control (0x18) granted
[    0.173568] ACPI: PCI Interrupt Link [LNKA] (IRQs 4 *7 10 11 12 14 15)
[    0.173609] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 7 *10 11 12 14 15)
[    0.173647] ACPI: PCI Interrupt Link [LNKC] (IRQs 4 7 10 *11 12 14 15)
[    0.173685] ACPI: PCI Interrupt Link [LNKD] (IRQs 4 7 *10 11 12 14 15)
[    0.173722] ACPI: PCI Interrupt Link [LNKE] (IRQs 4 7 10 11 12 14 15) *0, disabled.
[    0.173760] ACPI: PCI Interrupt Link [LNKF] (IRQs 4 7 10 11 12 14 15) *0, disabled.
[    0.173798] ACPI: PCI Interrupt Link [LNKG] (IRQs *4 10 11 12 14 15)
[    0.173835] ACPI: PCI Interrupt Link [LNKH] (IRQs 4 7 10 11 12 14 15) *0, disabled.
[    0.173945] vgaarb: device added: PCI:0000:01:05.0,decodes=io+mem,owns=io+mem,locks=none
[    0.173945] vgaarb: loaded
[    0.173945] vgaarb: bridge control possible 0000:01:05.0
[    0.173945] PCI: Using ACPI for IRQ routing
[    0.173945] PCI: pci_cache_line_size set to 64 bytes
[    0.173945] reserve RAM buffer: 000000000009fc00 - 000000000009ffff 
[    0.173945] reserve RAM buffer: 00000000cfeb0000 - 00000000cfffffff 
[    0.174033] pnp: PnP ACPI init
[    0.174055] ACPI: bus type pnp registered
[    0.176166] pnp 00:00: [bus 00-ff]
[    0.176169] pnp 00:00: [io  0x0cf8-0x0cff]
[    0.176172] pnp 00:00: [io  0x0000-0x0cf7 window]
[    0.176174] pnp 00:00: [io  0x0d00-0xffff window]
[    0.176177] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    0.176179] pnp 00:00: [mem 0x000d0000-0x000dffff window]
[    0.176182] pnp 00:00: [mem 0xcff00000-0xdfffffff window]
[    0.176184] pnp 00:00: [mem 0xf0000000-0xfebfffff window]
[    0.176255] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
[    0.176340] pnp 00:01: [mem 0x00000000-0xffffffffffffffff disabled]
[    0.176343] pnp 00:01: [mem 0x00000000-0xffffffffffffffff disabled]
[    0.176407] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.176449] pnp 00:02: [dma 4]
[    0.176451] pnp 00:02: [io  0x0000-0x000f]
[    0.176453] pnp 00:02: [io  0x0081-0x0083]
[    0.176456] pnp 00:02: [io  0x0087]
[    0.176458] pnp 00:02: [io  0x0089-0x008b]
[    0.176460] pnp 00:02: [io  0x008f]
[    0.176462] pnp 00:02: [io  0x00c0-0x00df]
[    0.176494] pnp 00:02: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.176503] pnp 00:03: [io  0x0070-0x0071]
[    0.176518] pnp 00:03: [irq 8]
[    0.176547] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.176555] pnp 00:04: [io  0x0061]
[    0.176585] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.176594] pnp 00:05: [io  0x00f0-0x00ff]
[    0.176599] pnp 00:05: [irq 13]
[    0.176630] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.176858] pnp 00:06: [mem 0xfed00000-0xfed003ff]
[    0.176889] pnp 00:06: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.176930] pnp 00:07: [mem 0xfec00000-0xfec00fff]
[    0.176933] pnp 00:07: [mem 0xfee00000-0xfee00fff]
[    0.176984] system 00:07: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.176987] system 00:07: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.176990] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.177089] pnp 00:08: [io  0x0010-0x001f]
[    0.177091] pnp 00:08: [io  0x0022-0x003f]
[    0.177094] pnp 00:08: [io  0x0062-0x0063]
[    0.177096] pnp 00:08: [io  0x0065-0x006f]
[    0.177099] pnp 00:08: [io  0x0072-0x007f]
[    0.177101] pnp 00:08: [io  0x0080]
[    0.177103] pnp 00:08: [io  0x0084-0x0086]
[    0.177105] pnp 00:08: [io  0x0088]
[    0.177107] pnp 00:08: [io  0x008c-0x008e]
[    0.177109] pnp 00:08: [io  0x0090-0x009f]
[    0.177112] pnp 00:08: [io  0x00a2-0x00bf]
[    0.177114] pnp 00:08: [io  0x00b1]
[    0.177116] pnp 00:08: [io  0x00e0-0x00ef]
[    0.177118] pnp 00:08: [io  0x04d0-0x04d1]
[    0.177121] pnp 00:08: [io  0x040b]
[    0.177122] pnp 00:08: [io  0x04d6]
[    0.177125] pnp 00:08: [io  0x0c00-0x0c01]
[    0.177127] pnp 00:08: [io  0x0c14]
[    0.177129] pnp 00:08: [io  0x0c50-0x0c51]
[    0.177131] pnp 00:08: [io  0x0c52]
[    0.177133] pnp 00:08: [io  0x0c6c]
[    0.177135] pnp 00:08: [io  0x0c6f]
[    0.177137] pnp 00:08: [io  0x0cd0-0x0cd1]
[    0.177139] pnp 00:08: [io  0x0cd2-0x0cd3]
[    0.177141] pnp 00:08: [io  0x0cd4-0x0cd5]
[    0.177144] pnp 00:08: [io  0x0cd6-0x0cd7]
[    0.177146] pnp 00:08: [io  0x0cd8-0x0cdf]
[    0.177148] pnp 00:08: [io  0x0800-0x089f]
[    0.177151] pnp 00:08: [io  0x0000-0xffffffffffffffff disabled]
[    0.177153] pnp 00:08: [io  0x0b00-0x0b0f]
[    0.177155] pnp 00:08: [io  0x0b20-0x0b3f]
[    0.177158] pnp 00:08: [io  0x0900-0x090f]
[    0.177160] pnp 00:08: [io  0x0910-0x091f]
[    0.177162] pnp 00:08: [io  0xfe00-0xfefe]
[    0.177165] pnp 00:08: [mem 0xffb80000-0xffbfffff]
[    0.177167] pnp 00:08: [mem 0xfec10000-0xfec1001f]
[    0.177250] system 00:08: [io  0x04d0-0x04d1] has been reserved
[    0.177253] system 00:08: [io  0x040b] has been reserved
[    0.177256] system 00:08: [io  0x04d6] has been reserved
[    0.177259] system 00:08: [io  0x0c00-0x0c01] has been reserved
[    0.177263] system 00:08: [io  0x0c14] has been reserved
[    0.177266] system 00:08: [io  0x0c50-0x0c51] has been reserved
[    0.177269] system 00:08: [io  0x0c52] has been reserved
[    0.177272] system 00:08: [io  0x0c6c] has been reserved
[    0.177275] system 00:08: [io  0x0c6f] has been reserved
[    0.177278] system 00:08: [io  0x0cd0-0x0cd1] has been reserved
[    0.177281] system 00:08: [io  0x0cd2-0x0cd3] has been reserved
[    0.177284] system 00:08: [io  0x0cd4-0x0cd5] has been reserved
[    0.177287] system 00:08: [io  0x0cd6-0x0cd7] has been reserved
[    0.177290] system 00:08: [io  0x0cd8-0x0cdf] has been reserved
[    0.177293] system 00:08: [io  0x0800-0x089f] has been reserved
[    0.177296] system 00:08: [io  0x0b00-0x0b0f] has been reserved
[    0.177299] system 00:08: [io  0x0b20-0x0b3f] has been reserved
[    0.177302] system 00:08: [io  0x0900-0x090f] has been reserved
[    0.177304] system 00:08: [io  0x0910-0x091f] has been reserved
[    0.177308] system 00:08: [io  0xfe00-0xfefe] has been reserved
[    0.177311] system 00:08: [mem 0xffb80000-0xffbfffff] has been reserved
[    0.177314] system 00:08: [mem 0xfec10000-0xfec1001f] has been reserved
[    0.177317] system 00:08: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.177501] pnp 00:09: [io  0x0000-0xffffffffffffffff disabled]
[    0.177504] pnp 00:09: [io  0x0000-0xffffffffffffffff disabled]
[    0.177506] pnp 00:09: [io  0x0290-0x029f]
[    0.177556] system 00:09: [io  0x0290-0x029f] has been reserved
[    0.177559] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.177589] pnp 00:0a: [mem 0xe0000000-0xefffffff]
[    0.177635] system 00:0a: [mem 0xe0000000-0xefffffff] has been reserved
[    0.177639] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.177767] pnp 00:0b: [mem 0x00000000-0x0009ffff]
[    0.177770] pnp 00:0b: [mem 0x000c0000-0x000cffff]
[    0.177773] pnp 00:0b: [mem 0x000e0000-0x000fffff]
[    0.177776] pnp 00:0b: [mem 0x00100000-0xcfefffff]
[    0.177778] pnp 00:0b: [mem 0xfec00000-0xffffffff]
[    0.177829] system 00:0b: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.177832] system 00:0b: [mem 0x000c0000-0x000cffff] could not be reserved
[    0.177835] system 00:0b: [mem 0x000e0000-0x000fffff] could not be reserved
[    0.177838] system 00:0b: [mem 0x00100000-0xcfefffff] could not be reserved
[    0.177841] system 00:0b: [mem 0xfec00000-0xffffffff] could not be reserved
[    0.177844] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.177940] pnp: PnP ACPI: found 12 devices
[    0.177942] ACPI: ACPI bus type pnp unregistered
[    0.177946] PnPBIOS: Disabled by ACPI PNP
[    0.214784] Switching to clocksource acpi_pm
[    0.214810] PCI: max bus depth: 1 pci_try_num: 2
[    0.214834] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.214837] pci 0000:00:01.0:   bridge window [io  0xc000-0xcfff]
[    0.214841] pci 0000:00:01.0:   bridge window [mem 0xfde00000-0xfdffffff]
[    0.214844] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.214849] pci 0000:00:09.0: PCI bridge to [bus 02-03]
[    0.214852] pci 0000:00:09.0:   bridge window [io  0xd000-0xdfff]
[    0.214856] pci 0000:00:09.0:   bridge window [mem 0xfe000000-0xfeafffff]
[    0.214860] pci 0000:00:09.0:   bridge window [mem 0xfa000000-0xfcefffff 64bit pref]
[    0.214864] pci 0000:00:0a.0: PCI bridge to [bus 04-04]
[    0.214867] pci 0000:00:0a.0:   bridge window [io  0xe000-0xefff]
[    0.214871] pci 0000:00:0a.0:   bridge window [mem 0xfeb00000-0xfebfffff]
[    0.214874] pci 0000:00:0a.0:   bridge window [mem 0xfcf00000-0xfcffffff 64bit pref]
[    0.214878] pci 0000:00:14.4: PCI bridge to [bus 05-05]
[    0.214909] pci 0000:00:09.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    0.214913] pci 0000:00:09.0: setting latency timer to 64
[    0.214920] pci 0000:00:0a.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    0.214924] pci 0000:00:0a.0: setting latency timer to 64
[    0.214931] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.214934] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.214936] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.214939] pci_bus 0000:00: resource 7 [mem 0xcff00000-0xdfffffff]
[    0.214942] pci_bus 0000:00: resource 8 [mem 0xf0000000-0xfebfffff]
[    0.214945] pci_bus 0000:01: resource 0 [io  0xc000-0xcfff]
[    0.214947] pci_bus 0000:01: resource 1 [mem 0xfde00000-0xfdffffff]
[    0.214950] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
[    0.214953] pci_bus 0000:02: resource 0 [io  0xd000-0xdfff]
[    0.214955] pci_bus 0000:02: resource 1 [mem 0xfe000000-0xfeafffff]
[    0.214958] pci_bus 0000:02: resource 2 [mem 0xfa000000-0xfcefffff 64bit pref]
[    0.214961] pci_bus 0000:04: resource 0 [io  0xe000-0xefff]
[    0.214963] pci_bus 0000:04: resource 1 [mem 0xfeb00000-0xfebfffff]
[    0.214966] pci_bus 0000:04: resource 2 [mem 0xfcf00000-0xfcffffff 64bit pref]
[    0.214969] pci_bus 0000:05: resource 4 [io  0x0000-0x0cf7]
[    0.214971] pci_bus 0000:05: resource 5 [io  0x0d00-0xffff]
[    0.214973] pci_bus 0000:05: resource 6 [mem 0x000a0000-0x000bffff]
[    0.214976] pci_bus 0000:05: resource 7 [mem 0xcff00000-0xdfffffff]
[    0.214978] pci_bus 0000:05: resource 8 [mem 0xf0000000-0xfebfffff]
[    0.215061] NET: Registered protocol family 2
[    0.215149] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.215502] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.215502] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.215502] TCP: Hash tables configured (established 131072 bind 65536)
[    0.215502] TCP reno registered
[    0.215502] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.215502] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.215502] NET: Registered protocol family 1
[    0.215502] pci 0000:00:01.0: MSI quirk detected; subordinate MSI disabled
[    0.215502] pci 0000:00:12.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.316030] pci 0000:00:12.0: PCI INT A disabled
[    0.316039] pci 0000:00:12.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.396026] pci 0000:00:12.1: PCI INT A disabled
[    0.396036] pci 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    0.396051] pci 0000:00:12.2: PCI INT B disabled
[    0.396059] pci 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    0.476026] pci 0000:00:13.0: PCI INT A disabled
[    0.476034] pci 0000:00:13.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    0.548024] pci 0000:00:13.1: PCI INT A disabled
[    0.548037] pci 0000:00:13.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    0.548053] pci 0000:00:13.2: PCI INT B disabled
[    0.548074] pci 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    0.620027] pci 0000:00:14.5: PCI INT C disabled
[    0.620039] pci 0000:01:05.0: Boot video device
[    0.620045] PCI: CLS 64 bytes, default 64
[    0.620116] Unpacking initramfs...
[    0.930065] Freeing initrd memory: 11876k freed
[    0.940976] audit: initializing netlink socket (disabled)
[    0.941000] type=2000 audit(1341577644.940:1): initialized
[    0.966342] highmem bounce pool size: 64 pages
[    0.966347] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    0.988747] VFS: Disk quotas dquot_6.5.2
[    0.988786] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.988863] msgmni has been set to 1694
[    0.989136] alg: No test for stdrng (krng)
[    0.989176] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.989180] io scheduler noop registered
[    0.989182] io scheduler deadline registered
[    0.989199] io scheduler cfq registered (default)
[    0.989304] pcieport 0000:00:09.0: setting latency timer to 64
[    0.989339] pcieport 0000:00:09.0: irq 40 for MSI/MSI-X
[    0.989393] pcieport 0000:00:0a.0: setting latency timer to 64
[    0.989419] pcieport 0000:00:0a.0: irq 41 for MSI/MSI-X
[    0.989495] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.989524] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.989527] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.989702] acpiphp: Slot [1] registered
[    0.989832] ERST: Table is not found!
[    0.989834] GHES: HEST is not enabled!
[    0.989847] isapnp: Scanning for PnP cards...
[    1.343668] isapnp: No Plug & Play device found
[    1.343762] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.352338] hpet_acpi_add: no address or irqs in _CRS
[    1.352351] Linux agpgart interface v0.103
[    1.352739] i8042: PNP: No PS/2 controller found. Probing ports directly.
[    1.355418] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.355426] serio: i8042 AUX port at 0x60,0x64 irq 12
[    1.355529] mousedev: PS/2 mouse device common for all mice
[    1.355590] rtc_cmos 00:03: RTC can wake from S4
[    1.355727] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    1.355756] rtc0: alarms up to one month, y3k, 114 bytes nvram
[    1.355771] cpuidle: using governor ladder
[    1.355773] cpuidle: using governor menu
[    1.356020] TCP cubic registered
[    1.356073] NET: Registered protocol family 10
[    1.356617] Mobile IPv6
[    1.356619] NET: Registered protocol family 17
[    1.356623] Registering the dns_resolver key type
[    1.356648] Using IPI No-Shortcut mode
[    1.356805] PM: Hibernation image not present or could not be loaded.
[    1.356817] registered taskstats version 1
[    1.367981] rtc_cmos 00:03: setting system clock to 2012-07-06 12:27:25 UTC (1341577645)
[    1.368037] Initializing network drop monitor service
[    1.368168] Freeing unused kernel memory: 412k freed
[    1.368455] Write protecting the kernel text: 2840k
[    1.368488] Write protecting the kernel read-only data: 1088k
[    1.368490] NX-protecting the kernel data: 3304k
[    1.434717] udevd[52]: starting version 175
[    1.480982] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    1.481008] r8169 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    1.481037] r8169 0000:04:00.0: setting latency timer to 64
[    1.481086] r8169 0000:04:00.0: irq 42 for MSI/MSI-X
[    1.481617] r8169 0000:04:00.0: eth0: RTL8168c/8111c at 0xf820a000, 00:19:66:8b:09:1a, XID 1c4000c0 IRQ 42
[    1.481621] r8169 0000:04:00.0: eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko]
[    1.508236] usbcore: registered new interface driver usbfs
[    1.508265] usbcore: registered new interface driver hub
[    1.508469] SCSI subsystem initialized
[    1.517659] usbcore: registered new device driver usb
[    1.518232] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.518269] ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    1.518294] ehci_hcd 0000:00:12.2: EHCI Host Controller
[    1.518326] ehci_hcd 0000:00:12.2: new USB bus registered, assigned bus number 1
[    1.518338] ehci_hcd 0000:00:12.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    1.518370] QUIRK: Enable AMD PLL fix
[    1.518373] ehci_hcd 0000:00:12.2: applying AMD SB600/SB700 USB freeze workaround
[    1.518387] ehci_hcd 0000:00:12.2: debug port 1
[    1.518418] ehci_hcd 0000:00:12.2: irq 17, io mem 0xfddff000
[    1.528417] ehci_hcd 0000:00:12.2: USB 2.0 started, EHCI 1.00
[    1.528480] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.528483] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.528486] usb usb1: Product: EHCI Host Controller
[    1.528488] usb usb1: Manufacturer: Linux 3.2.0-3-686-pae ehci_hcd
[    1.528490] usb usb1: SerialNumber: 0000:00:12.2
[    1.528636] hub 1-0:1.0: USB hub found
[    1.528641] hub 1-0:1.0: 6 ports detected
[    1.528753] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    1.528788] ehci_hcd 0000:00:13.2: EHCI Host Controller
[    1.528802] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
[    1.528812] ehci_hcd 0000:00:13.2: applying AMD SB700/SB800/Hudson-2/3 EHCI dummy qh workaround
[    1.528839] ehci_hcd 0000:00:13.2: applying AMD SB600/SB700 USB freeze workaround
[    1.528854] ehci_hcd 0000:00:13.2: debug port 1
[    1.528891] ehci_hcd 0000:00:13.2: irq 19, io mem 0xfddf6800
[    1.532930] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.533721] libata version 3.00 loaded.
[    1.540104] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00
[    1.540155] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.540158] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.540161] usb usb2: Product: EHCI Host Controller
[    1.540163] usb usb2: Manufacturer: Linux 3.2.0-3-686-pae ehci_hcd
[    1.540165] usb usb2: SerialNumber: 0000:00:13.2
[    1.541072] hub 2-0:1.0: USB hub found
[    1.541079] hub 2-0:1.0: 6 ports detected
[    1.541389] ohci_hcd 0000:00:12.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.541417] ohci_hcd 0000:00:12.0: OHCI Host Controller
[    1.541431] ohci_hcd 0000:00:12.0: new USB bus registered, assigned bus number 3
[    1.541477] ohci_hcd 0000:00:12.0: irq 16, io mem 0xfddfe000
[    1.600058] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.600063] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.600065] usb usb3: Product: OHCI Host Controller
[    1.600067] usb usb3: Manufacturer: Linux 3.2.0-3-686-pae ohci_hcd
[    1.600069] usb usb3: SerialNumber: 0000:00:12.0
[    1.600231] hub 3-0:1.0: USB hub found
[    1.600240] hub 3-0:1.0: 3 ports detected
[    1.600336] ohci_hcd 0000:00:12.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.600361] ohci_hcd 0000:00:12.1: OHCI Host Controller
[    1.600371] ohci_hcd 0000:00:12.1: new USB bus registered, assigned bus number 4
[    1.600394] ohci_hcd 0000:00:12.1: irq 16, io mem 0xfddfd000
[    1.660035] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[    1.660038] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.660040] usb usb4: Product: OHCI Host Controller
[    1.660042] usb usb4: Manufacturer: Linux 3.2.0-3-686-pae ohci_hcd
[    1.660044] usb usb4: SerialNumber: 0000:00:12.1
[    1.660175] hub 4-0:1.0: USB hub found
[    1.660182] hub 4-0:1.0: 3 ports detected
[    1.660504] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    1.660519] ohci_hcd 0000:00:13.0: OHCI Host Controller
[    1.660526] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 5
[    1.660556] ohci_hcd 0000:00:13.0: irq 18, io mem 0xfddfc000
[    1.720032] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[    1.720035] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.720038] usb usb5: Product: OHCI Host Controller
[    1.720040] usb usb5: Manufacturer: Linux 3.2.0-3-686-pae ohci_hcd
[    1.720042] usb usb5: SerialNumber: 0000:00:13.0
[    1.720182] hub 5-0:1.0: USB hub found
[    1.720189] hub 5-0:1.0: 3 ports detected
[    1.720863] ahci 0000:00:11.0: version 3.0
[    1.720894] ahci 0000:00:11.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[    1.721096] ahci 0000:00:11.0: AHCI 0001.0100 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
[    1.721099] ahci 0000:00:11.0: flags: 64bit ncq sntf ilck pm led clo pmp pio slum part ccc 
[    1.722730] scsi0 : ahci
[    1.722871] scsi1 : ahci
[    1.722950] scsi2 : ahci
[    1.723028] scsi3 : ahci
[    1.723127] scsi4 : ahci
[    1.723207] scsi5 : ahci
[    1.723274] ata1: SATA max UDMA/133 abar m1024@0xfddff800 port 0xfddff900 irq 22
[    1.723278] ata2: SATA max UDMA/133 abar m1024@0xfddff800 port 0xfddff980 irq 22
[    1.723282] ata3: SATA max UDMA/133 abar m1024@0xfddff800 port 0xfddffa00 irq 22
[    1.723286] ata4: SATA max UDMA/133 abar m1024@0xfddff800 port 0xfddffa80 irq 22
[    1.723290] ata5: SATA max UDMA/133 abar m1024@0xfddff800 port 0xfddffb00 irq 22
[    1.723294] ata6: SATA max UDMA/133 abar m1024@0xfddff800 port 0xfddffb80 irq 22
[    1.723385] pata_atiixp 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    1.723445] pata_atiixp 0000:00:14.1: setting latency timer to 64
[    1.723801] scsi6 : pata_atiixp
[    1.723894] scsi7 : pata_atiixp
[    1.724570] ata7: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xff00 irq 14
[    1.724573] ata8: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xff08 irq 15
[    1.724630] ohci_hcd 0000:00:13.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    1.724656] ohci_hcd 0000:00:13.1: OHCI Host Controller
[    1.724677] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 6
[    1.724704] ohci_hcd 0000:00:13.1: irq 18, io mem 0xfddf7000
[    1.784046] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[    1.784049] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.784051] usb usb6: Product: OHCI Host Controller
[    1.784053] usb usb6: Manufacturer: Linux 3.2.0-3-686-pae ohci_hcd
[    1.784055] usb usb6: SerialNumber: 0000:00:13.1
[    1.784246] hub 6-0:1.0: USB hub found
[    1.784253] hub 6-0:1.0: 3 ports detected
[    1.784330] ohci_hcd 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    1.784342] ohci_hcd 0000:00:14.5: OHCI Host Controller
[    1.784350] ohci_hcd 0000:00:14.5: new USB bus registered, assigned bus number 7
[    1.784369] ohci_hcd 0000:00:14.5: irq 18, io mem 0xfddf5000
[    1.844049] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
[    1.844053] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.844055] usb usb7: Product: OHCI Host Controller
[    1.844057] usb usb7: Manufacturer: Linux 3.2.0-3-686-pae ohci_hcd
[    1.844059] usb usb7: SerialNumber: 0000:00:14.5
[    1.844205] hub 7-0:1.0: USB hub found
[    1.844211] hub 7-0:1.0: 2 ports detected
[    1.896577] ata8.00: ATAPI: TOSHIBA DVD-ROM SD-M1712, 1004, max UDMA/33
[    1.896584] ata8.01: ATAPI: HL-DT-ST DVDRAM GSA-4167B, DL12, max UDMA/33
[    1.912510] ata8.00: configured for UDMA/33
[    1.928425] ata8.01: configured for UDMA/33
[    2.040050] ata5: SATA link down (SStatus 0 SControl 300)
[    2.040085] ata4: SATA link down (SStatus 0 SControl 300)
[    2.040163] ata3: SATA link down (SStatus 0 SControl 300)
[    2.044033] ata6: SATA link down (SStatus 0 SControl 300)
[    2.104024] usb 3-3: new low-speed USB device number 2 using ohci_hcd
[    2.212031] ata2: softreset failed (device not ready)
[    2.212070] ata2: applying PMP SRST workaround and retrying
[    2.212088] ata1: softreset failed (device not ready)
[    2.212128] ata1: applying PMP SRST workaround and retrying
[    2.269089] usb 3-3: New USB device found, idVendor=1241, idProduct=1122
[    2.269092] usb 3-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.384056] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.384082] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.384420] ata1.00: ATA-9: M4-CT256M4SSD2, 0309, max UDMA/100
[    2.384423] ata1.00: 500118192 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    2.384797] ata1.00: configured for UDMA/100
[    2.384989] scsi 0:0:0:0: Direct-Access     ATA      M4-CT256M4SSD2   0309 PQ: 0 ANSI: 5
[    2.390523] ata2.00: ATA-8: WDC WD20EARS-60MVWB0, 51.0AB51, max UDMA/100
[    2.390526] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
[    2.396483] ata2.00: configured for UDMA/100
[    2.396590] scsi 1:0:0:0: Direct-Access     ATA      WDC WD20EARS-60M 51.0 PQ: 0 ANSI: 5
[    2.417734] scsi 7:0:0:0: CD-ROM            TOSHIBA  DVD-ROM SD-M1712 1004 PQ: 0 ANSI: 5
[    2.421553] scsi 7:0:1:0: CD-ROM            HL-DT-ST DVDRAM GSA-4167B DL12 PQ: 0 ANSI: 5
[    2.435144] sd 0:0:0:0: [sda] 500118192 512-byte logical blocks: (256 GB/238 GiB)
[    2.435207] sd 0:0:0:0: [sda] Write Protect is off
[    2.435210] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.435228] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.435960] sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[    2.435963] sd 1:0:0:0: [sdb] 4096-byte physical blocks
[    2.436035] sd 1:0:0:0: [sdb] Write Protect is off
[    2.436038] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    2.436055] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.437380]  sda: sda1 sda2 sda3
[    2.437729] sd 0:0:0:0: [sda] Attached SCSI disk
[    2.439959] sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray
[    2.439965] cdrom: Uniform CD-ROM driver Revision: 3.20
[    2.440173] sr 7:0:0:0: Attached scsi CD-ROM sr0
[    2.441474] input: HID 1241:1122 as /devices/pci0000:00/0000:00:12.0/usb3/3-3/3-3:1.0/input/input0
[    2.441608] generic-usb 0003:1241:1122.0001: input,hidraw0: USB HID v1.00 Mouse [HID 1241:1122] on usb-0000:00:12.0-3/input0
[    2.441631] usbcore: registered new interface driver usbhid
[    2.441633] usbhid: USB HID core driver
[    2.448302] sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    2.448638] sr 7:0:1:0: Attached scsi CD-ROM sr1
[    2.451218]  sdb: sdb1 sdb2
[    2.451559] sd 1:0:0:0: [sdb] Attached SCSI disk
[    2.532044] usb 4-1: new low-speed USB device number 2 using ohci_hcd
[    2.705091] usb 4-1: New USB device found, idVendor=046d, idProduct=c30f
[    2.705096] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.705099] usb 4-1: Product: Logitech USB Keyboard
[    2.705101] usb 4-1: Manufacturer: Logitech
[    2.713455] input: Logitech Logitech USB Keyboard as /devices/pci0000:00/0000:00:12.1/usb4/4-1/4-1:1.0/input/input1
[    2.713625] generic-usb 0003:046D:C30F.0002: input,hidraw1: USB HID v1.10 Keyboard [Logitech Logitech USB Keyboard] on usb-0000:00:12.1-1/input0
[    2.725263] md: raid1 personality registered for level 1
[    2.726211] input: Logitech Logitech USB Keyboard as /devices/pci0000:00/0000:00:12.1/usb4/4-1/4-1:1.1/input/input2
[    2.726316] generic-usb 0003:046D:C30F.0003: input,hidraw2: USB HID v1.10 Device [Logitech Logitech USB Keyboard] on usb-0000:00:12.1-1/input1
[    2.804070] mdadm: sending ioctl 800c0910 to a partition!
[    2.804074] mdadm: sending ioctl 800c0910 to a partition!
[    2.804090] mdadm: sending ioctl 1261 to a partition!
[    2.804093] mdadm: sending ioctl 1261 to a partition!
[    2.804298] mdadm: sending ioctl 1261 to a partition!
[    2.804300] mdadm: sending ioctl 1261 to a partition!
[    2.804433] mdadm: sending ioctl 1261 to a partition!
[    2.804436] mdadm: sending ioctl 1261 to a partition!
[    2.804551] mdadm: sending ioctl 1261 to a partition!
[    2.804553] mdadm: sending ioctl 1261 to a partition!
[    2.808396] md: md0 stopped.
[    2.809273] md: bind<sdb1>
[    2.810926] bio: create slab <bio-1> at 1
[    2.811000] md/raid1:md0: active with 1 out of 2 mirrors
[    2.811032] md0: detected capacity change from 0 to 509804544
[    2.812792]  md0: unknown partition table
[    2.875651] md: md1 stopped.
[    2.877544] md: bind<sdb2>
[    2.879363] md/raid1:md1: active with 1 out of 2 mirrors
[    2.879396] md1: detected capacity change from 0 to 1999886286848
[    2.881536]  md1: unknown partition table
[    2.885507] device-mapper: uevent: version 1.0.3
[    2.885591] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@xxxxxxxxxx
[   53.094184] scsi_verify_blk_ioctl: 84 callbacks suppressed
[   53.094189] mdadm: sending ioctl 1261 to a partition!
[   53.094192] mdadm: sending ioctl 1261 to a partition!
[   53.871783] fstype: sending ioctl 540f to a partition!
[   53.981783] PM: Starting manual resume from disk
[   53.981788] PM: Hibernation image partition 253:2 present
[   53.981790] PM: Looking for hibernation image.
[   53.982072] PM: Image not found (code -22)
[   53.982076] PM: Hibernation image not present or could not be loaded.
[   53.991690] kjournald starting.  Commit interval 5 seconds
[   53.991722] EXT3-fs (dm-1): mounted filesystem with ordered data mode
[   55.238915] udevd[438]: starting version 175
[   55.639123] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input3
[   55.639132] ACPI: Power Button [PWRB]
[   55.639217] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[   55.639220] ACPI: Power Button [PWRF]
[   55.656114] wmi: Mapper loaded
[   55.690525] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[   55.708652] udevd[465]: renamed network interface eth0 to eth3
[   55.760234] powernow-k8: Found 1 AMD Athlon(tm) Dual Core Processor 4850e (2 cpu cores) (version 2.20.00)
[   55.760292] powernow-k8: fid 0x11 (2500 MHz), vid 0xe
[   55.760294] powernow-k8: fid 0x10 (2400 MHz), vid 0xf
[   55.760296] powernow-k8: fid 0xe (2200 MHz), vid 0x11
[   55.760298] powernow-k8: fid 0xc (2000 MHz), vid 0x13
[   55.760300] powernow-k8: fid 0xa (1800 MHz), vid 0x15
[   55.760302] powernow-k8: fid 0x2 (1000 MHz), vid 0x16
[   55.933332] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
[   56.013151] mdadm: sending ioctl 1261 to a partition!
[   56.013160] mdadm: sending ioctl 1261 to a partition!
[   56.013882] mdadm: sending ioctl 1261 to a partition!
[   56.013892] mdadm: sending ioctl 1261 to a partition!
[   56.159642] ACPI: resource piix4_smbus [io  0x0b00-0x0b07] conflicts with ACPI region SOR1 [io 0xb00-0xb0f]
[   56.159656] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[   56.199378] SP5100 TCO timer: SP5100 TCO WatchDog Timer Driver v0.01
[   56.199554] SP5100 TCO timer: mmio address 0xfec000f0 already in use
[   56.267682] [drm] Initialized drm 1.1.0 20060810
[   56.754799] [drm] radeon kernel modesetting enabled.
[   56.755027] radeon 0000:01:05.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[   56.755038] radeon 0000:01:05.0: setting latency timer to 64
[   56.755660] [drm] initializing kernel modesetting (RS780 0x1002:0x9610 0x1849:0x9610).
[   56.755716] [drm] register mmio base: 0xFDFF0000
[   56.755721] [drm] register mmio size: 65536
[   56.764521] ATOM BIOS: ASROCK
[   56.764575] radeon 0000:01:05.0: VRAM: 256M 0x00000000C0000000 - 0x00000000CFFFFFFF (256M used)
[   56.764582] radeon 0000:01:05.0: GTT: 512M 0x00000000A0000000 - 0x00000000BFFFFFFF
[   56.765286] [drm] Detected VRAM RAM=256M, BAR=256M
[   56.765296] [drm] RAM width 32bits DDR
[   56.765440] [TTM] Zone  kernel: Available graphics memory: 434072 kiB.
[   56.765445] [TTM] Zone highmem: Available graphics memory: 1943804 kiB.
[   56.765450] [TTM] Initializing pool allocator.
[   56.765512] [drm] radeon: 256M of VRAM memory ready
[   56.765517] [drm] radeon: 512M of GTT memory ready.
[   56.765554] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[   56.765559] [drm] Driver supports precise vblank timestamp query.
[   56.765588] [drm] radeon: irq initialized.
[   56.765600] [drm] GART: num cpu pages 131072, num gpu pages 131072
[   56.769872] [drm] Loading RS780 Microcode
[   56.889411] snd_hda_intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   56.935113] mdadm: sending ioctl 800c0910 to a partition!
[   56.935126] mdadm: sending ioctl 800c0910 to a partition!
[   56.935149] mdadm: sending ioctl 1261 to a partition!
[   57.010754] [drm] PCIE GART of 512M enabled (table at 0x00000000C0040000).
[   57.010876] radeon 0000:01:05.0: WB enabled
[   57.042357] [drm] ring test succeeded in 1 usecs
[   57.042717] [drm] radeon: ib pool ready.
[   57.042871] [drm] ib test succeeded in 0 usecs
[   57.044640] [drm] Radeon Display Connectors
[   57.044647] [drm] Connector 0:
[   57.044651] [drm]   VGA
[   57.044657] [drm]   DDC: 0x7e40 0x7e40 0x7e44 0x7e44 0x7e48 0x7e48 0x7e4c 0x7e4c
[   57.044662] [drm]   Encoders:
[   57.044665] [drm]     CRT1: INTERNAL_KLDSCP_DAC1
[   57.044669] [drm] Connector 1:
[   57.044673] [drm]   DVI-D
[   57.044676] [drm]   HPD3
[   57.044681] [drm]   DDC: 0x7e50 0x7e50 0x7e54 0x7e54 0x7e58 0x7e58 0x7e5c 0x7e5c
[   57.044686] [drm]   Encoders:
[   57.044689] [drm]     DFP3: INTERNAL_KLDSCP_LVTMA
[   57.044733] [drm] radeon: power management initialized
[   57.143530] [drm] fb mappable at 0xD0142000
[   57.143535] [drm] vram apper at 0xD0000000
[   57.143539] [drm] size 5242880
[   57.143542] [drm] fb depth is 24
[   57.143546] [drm]    pitch is 5120
[   57.143705] fbcon: radeondrmfb (fb0) is primary device
[   57.187078] Console: switching to colour frame buffer device 160x64
[   57.206048] fb0: radeondrmfb frame buffer device
[   57.206053] drm: registered panic notifier
[   57.206066] [drm] Initialized radeon 2.12.0 20080528 for 0000:01:05.0 on minor 0
[   57.917436] EXT3-fs (dm-1): using internal journal
[   59.044677] fuse init (API version 7.17)
[   59.136442] loop: module loaded
[   59.197768] w83627ehf: Found W83627EHG chip at 0x290
[   59.327620] kvm: Nested Virtualization enabled
[   59.510210] scsi_verify_blk_ioctl: 33 callbacks suppressed
[   59.510218] mdadm: sending ioctl 800c0910 to a partition!
[   59.510230] mdadm: sending ioctl 1261 to a partition!
[   59.520181] mdadm: sending ioctl 1261 to a partition!
[   59.520600] mdadm: sending ioctl 1261 to a partition!
[   59.534846] mdadm: sending ioctl 1261 to a partition!
[   59.535722] mdadm: sending ioctl 1261 to a partition!
[   59.535954] mdadm: sending ioctl 1261 to a partition!
[   59.604981] mdadm: sending ioctl 800c0910 to a partition!
[   59.604996] mdadm: sending ioctl 1261 to a partition!
[   59.614923] mdadm: sending ioctl 1261 to a partition!
[   61.332587] Adding 4194300k swap on /dev/mapper/speicher-swap.  Priority:-1 extents:1 across:4194300k 
[   63.606743] kjournald starting.  Commit interval 5 seconds
[   63.638864] EXT3-fs (md0): using internal journal
[   63.638877] EXT3-fs (md0): mounted filesystem with ordered data mode
[   63.745682] kjournald starting.  Commit interval 5 seconds
[   63.809331] EXT3-fs (dm-6): using internal journal
[   63.809346] EXT3-fs (dm-6): mounted filesystem with ordered data mode
[   64.096407] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[   64.096942] SGI XFS Quota Management subsystem
[   64.140449] XFS (dm-7): Mounting Filesystem
[   64.380160] XFS (dm-7): Ending clean mount
[   64.402685] XFS (dm-8): Mounting Filesystem
[   64.764518] XFS (dm-8): Ending clean mount
[   64.828428] REISERFS (device dm-5): found reiserfs format "3.6" with standard journal
[   64.828450] REISERFS (device dm-5): using ordered data mode
[   64.828456] reiserfs: using flush barriers
[   64.838182] REISERFS (device dm-5): journal params: device dm-5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[   64.839637] REISERFS (device dm-5): checking transaction log (dm-5)
[   64.952634] REISERFS (device dm-5): Using r5 hash to sort names
[   65.004403] kjournald starting.  Commit interval 5 seconds
[   65.004877] EXT3-fs (dm-3): using internal journal
[   65.004889] EXT3-fs (dm-3): mounted filesystem with ordered data mode
[   65.037068] kjournald starting.  Commit interval 5 seconds
[   65.037530] EXT3-fs (dm-4): using internal journal
[   65.037541] EXT3-fs (dm-4): mounted filesystem with ordered data mode
[   89.531034] postgres (2085): /proc/2085/oom_adj is deprecated, please use /proc/2085/oom_score_adj instead.
[  102.454521] r8169 0000:04:00.0: eth3: link down
[  102.454543] r8169 0000:04:00.0: eth3: link down
[  102.455049] ADDRCONF(NETDEV_UP): eth3: link is not ready
[  104.131381] r8169 0000:04:00.0: eth3: link up
[  104.131770] ADDRCONF(NETDEV_CHANGE): eth3: link becomes ready
[  106.298595] ip_tables: (C) 2000-2006 Netfilter Core Team
[  106.390084] ip6_tables: (C) 2000-2006 Netfilter Core Team
[  114.928034] eth3: no IPv6 routers present
[  184.448047] usb 2-4: new high-speed USB device number 2 using ehci_hcd
[  184.581655] usb 2-4: New USB device found, idVendor=0204, idProduct=6025
[  184.581660] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  184.581663] usb 2-4: Product: Flash Disk
[  184.581665] usb 2-4: SerialNumber: 00CCCBB99999
[  184.679403] usbcore: registered new interface driver uas
[  184.684826] Initializing USB Mass Storage driver...
[  184.684987] scsi8 : usb-storage 2-4:1.0
[  184.685119] usbcore: registered new interface driver usb-storage
[  184.685122] USB Mass Storage support registered.
[  185.684840] scsi 8:0:0:0: Direct-Access              Flash Disk       5.00 PQ: 0 ANSI: 2
[  185.689940] sd 8:0:0:0: [sdc] 2065920 512-byte logical blocks: (1.05 GB/1008 MiB)
[  185.690406] sd 8:0:0:0: [sdc] Write Protect is off
[  185.690414] sd 8:0:0:0: [sdc] Mode Sense: 0b 00 00 08
[  185.690906] sd 8:0:0:0: [sdc] No Caching mode page present
[  185.690914] sd 8:0:0:0: [sdc] Assuming drive cache: write through
[  185.698155] sd 8:0:0:0: [sdc] No Caching mode page present
[  185.698168] sd 8:0:0:0: [sdc] Assuming drive cache: write through
[  185.699346]  sdc: sdc1
[  185.702034] sd 8:0:0:0: [sdc] No Caching mode page present
[  185.702043] sd 8:0:0:0: [sdc] Assuming drive cache: write through
[  185.702051] sd 8:0:0:0: [sdc] Attached SCSI removable disk
[  189.878078] colord-sane[4227]: segfault at be ip b55efdf6 sp b716904c error 4 in libdbus-1.so.3.7.2[b55dc000+49000]
[  368.733131] FAT-fs (sdc1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[  387.435662] sdc: detected capacity change from 1057751040 to 0
[  939.286200] usb 2-4: USB disconnect, device number 2
[  941.660054] usb 2-4: new high-speed USB device number 3 using ehci_hcd
[  941.793609] usb 2-4: New USB device found, idVendor=0204, idProduct=6025
[  941.793615] usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  941.793618] usb 2-4: Product: Flash Disk
[  941.793620] usb 2-4: SerialNumber: 00CCCBB99999
[  941.793964] scsi9 : usb-storage 2-4:1.0
[  942.792647] scsi 9:0:0:0: Direct-Access              Flash Disk       5.00 PQ: 0 ANSI: 2
[  942.795866] sd 9:0:0:0: [sdc] 2065920 512-byte logical blocks: (1.05 GB/1008 MiB)
[  942.796364] sd 9:0:0:0: [sdc] Write Protect is off
[  942.796367] sd 9:0:0:0: [sdc] Mode Sense: 0b 00 00 08
[  942.796863] sd 9:0:0:0: [sdc] No Caching mode page present
[  942.796868] sd 9:0:0:0: [sdc] Assuming drive cache: write through
[  942.803115] sd 9:0:0:0: [sdc] No Caching mode page present
[  942.803123] sd 9:0:0:0: [sdc] Assuming drive cache: write through
[  942.804265]  sdc: sdc1
[  942.814238] sd 9:0:0:0: [sdc] No Caching mode page present
[  942.814246] sd 9:0:0:0: [sdc] Assuming drive cache: write through
[  942.814250] sd 9:0:0:0: [sdc] Attached SCSI removable disk
[  943.068239] FAT-fs (sdc1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 7531.500964] ata2: exception Emask 0x40 SAct 0x0 SErr 0x800 action 0x7
[ 7531.500978] ata2: SError: { HostInt }
[ 7531.500990] ata2: hard resetting link
[ 7531.992053] ata2: softreset failed (device not ready)
[ 7531.992067] ata2: applying PMP SRST workaround and retrying
[ 7532.164073] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 7532.176364] ata2.00: configured for UDMA/100
[ 7532.192095] ata2: EH complete
[ 7534.142898] PM: Syncing filesystems ... done.
[ 7534.429111] PM: Preparing system for mem sleep
[ 7534.464468] Freezing user space processes ... (elapsed 0.01 seconds) done.
[ 7534.480064] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[ 7534.496029] PM: Entering mem sleep
[ 7534.496067] Suspending console(s) (use no_console_suspend to debug)
[ 7534.496535] sd 1:0:0:0: [sdb] Synchronizing SCSI cache
[ 7534.496626] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 7534.496914] sd 1:0:0:0: [sdb] Stopping disk
[ 7534.497441] r8169 0000:04:00.0: eth3: link down
[ 7534.509575] sd 0:0:0:0: [sda] Stopping disk
[ 7534.513113] pata_atiixp 0000:00:14.1: PCI INT A disabled
[ 7534.513198] ohci_hcd 0000:00:12.1: PCI INT A disabled
[ 7534.513207] ohci_hcd 0000:00:12.0: PCI INT A disabled
[ 7534.528032] ehci_hcd 0000:00:13.2: PCI INT B disabled
[ 7534.564063] ehci_hcd 0000:00:12.2: PCI INT B disabled
[ 7534.576094] ohci_hcd 0000:00:14.5: PCI INT C disabled
[ 7534.576114] ohci_hcd 0000:00:13.1: PCI INT A disabled
[ 7534.576131] ohci_hcd 0000:00:13.0: PCI INT A disabled
[ 7534.663494] radeon 0000:01:05.0: PCI INT A disabled
[ 7534.820083] snd_hda_intel 0000:00:14.2: PCI INT A disabled
[ 7535.172360] ahci 0000:00:11.0: PCI INT A disabled
[ 7535.188056] PM: suspend of devices complete after 691.758 msecs
[ 7535.188282] r8169 0000:04:00.0: PME# enabled
[ 7535.188293] pcieport 0000:00:0a.0: wake-up capability enabled by ACPI
[ 7535.204138] ohci_hcd 0000:00:14.5: wake-up capability enabled by ACPI
[ 7535.204238] ehci_hcd 0000:00:13.2: PME# enabled
[ 7535.204242] ehci_hcd 0000:00:13.2: wake-up capability enabled by ACPI
[ 7535.220056] ohci_hcd 0000:00:13.1: wake-up capability enabled by ACPI
[ 7535.220083] ohci_hcd 0000:00:13.0: wake-up capability enabled by ACPI
[ 7535.220115] ehci_hcd 0000:00:12.2: PME# enabled
[ 7535.220119] ehci_hcd 0000:00:12.2: wake-up capability enabled by ACPI
[ 7535.236041] ohci_hcd 0000:00:12.1: wake-up capability enabled by ACPI
[ 7535.236068] ohci_hcd 0000:00:12.0: wake-up capability enabled by ACPI
[ 7535.236127] PM: late suspend of devices complete after 48.066 msecs
[ 7535.236259] ACPI: Preparing to enter system sleep state S3
[ 7535.636274] PM: Saving platform NVS memory
[ 7535.636962] Disabling non-boot CPUs ...
[ 7535.740019] CPU 1 is now offline
[ 7535.740640] ACPI: Low-level resume complete
[ 7535.740640] PM: Restoring platform NVS memory
[ 7535.740640] Enabling non-boot CPUs ...
[ 7535.740640] Booting Node 0 Processor 1 APIC 0x1
[ 7535.740640] smpboot cpu 1: start_ip = 9b000
[ 7535.638290] Initializing CPU#1
[ 7535.638290] Calibrating delay loop (skipped) already calibrated this CPU
[ 7535.752434] NMI watchdog enabled, takes one hw-pmu counter.
[ 7535.752665] CPU1 is up
[ 7535.753287] ACPI: Waking up from system sleep state S3
[ 7535.753773] pcieport 0000:00:09.0: restoring config space at offset 0x1 (was 0x100107, writing 0x100507)
[ 7535.753804] pcieport 0000:00:0a.0: restoring config space at offset 0x1 (was 0x100107, writing 0x100507)
[ 7535.753829] ahci 0000:00:11.0: restoring config space at offset 0xf (was 0x100, writing 0x104)
[ 7535.753885] ohci_hcd 0000:00:12.0: wake-up capability disabled by ACPI
[ 7535.753913] ohci_hcd 0000:00:12.1: wake-up capability disabled by ACPI
[ 7535.768034] ehci_hcd 0000:00:12.2: BAR 0: set to [mem 0xfddff000-0xfddff0ff] (PCI address [0xfddff000-0xfddff0ff])
[ 7535.768063] ehci_hcd 0000:00:12.2: restoring config space at offset 0x1 (was 0x2b00000, writing 0x2b00112)
[ 7535.768078] ehci_hcd 0000:00:12.2: wake-up capability disabled by ACPI
[ 7535.768083] ehci_hcd 0000:00:12.2: PME# disabled
[ 7535.768110] ohci_hcd 0000:00:13.0: wake-up capability disabled by ACPI
[ 7535.768138] ohci_hcd 0000:00:13.1: wake-up capability disabled by ACPI
[ 7535.784029] ehci_hcd 0000:00:13.2: BAR 0: set to [mem 0xfddf6800-0xfddf68ff] (PCI address [0xfddf6800-0xfddf68ff])
[ 7535.784058] ehci_hcd 0000:00:13.2: restoring config space at offset 0x1 (was 0x2b00000, writing 0x2b00113)
[ 7535.784072] ehci_hcd 0000:00:13.2: wake-up capability disabled by ACPI
[ 7535.784077] ehci_hcd 0000:00:13.2: PME# disabled
[ 7535.784130] pata_atiixp 0000:00:14.1: restoring config space at offset 0x3 (was 0x0, writing 0x4000)
[ 7535.784168] snd_hda_intel 0000:00:14.2: restoring config space at offset 0x1 (was 0x4100006, writing 0x4100002)
[ 7535.784249] ohci_hcd 0000:00:14.5: wake-up capability disabled by ACPI
[ 7535.784275] radeon 0000:01:05.0: restoring config space at offset 0xf (was 0x1ff, writing 0x10b)
[ 7535.784286] radeon 0000:01:05.0: restoring config space at offset 0x3 (was 0x800000, writing 0x800010)
[ 7535.784290] radeon 0000:01:05.0: restoring config space at offset 0x1 (was 0x40100107, writing 0x100107)
[ 7535.784316] r8169 0000:04:00.0: restoring config space at offset 0xc (was 0x0, writing 0xfebf0000)
[ 7535.784324] r8169 0000:04:00.0: restoring config space at offset 0x8 (was 0xc, writing 0xfcfe000c)
[ 7535.784330] r8169 0000:04:00.0: restoring config space at offset 0x6 (was 0xc, writing 0xfcfff00c)
[ 7535.784339] r8169 0000:04:00.0: restoring config space at offset 0x1 (was 0x100107, writing 0x100507)
[ 7535.784507] PM: early resume of devices complete after 30.812 msecs
[ 7535.784602] ahci 0000:00:11.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 7535.784692] ohci_hcd 0000:00:12.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 7535.784750] ohci_hcd 0000:00:12.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 7535.784876] ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 7535.784895] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 7535.784906] ohci_hcd 0000:00:13.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 7535.784921] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 7535.784934] pata_atiixp 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 7535.784950] snd_hda_intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 7535.784960] ohci_hcd 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 7535.784986] radeon 0000:01:05.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 7535.784990] radeon 0000:01:05.0: setting latency timer to 64
[ 7535.789265] pcieport 0000:00:0a.0: wake-up capability disabled by ACPI
[ 7535.789271] r8169 0000:04:00.0: PME# disabled
[ 7535.793201] sd 0:0:0:0: [sda] Starting disk
[ 7535.793252] sd 1:0:0:0: [sdb] Starting disk
[ 7535.808227] r8169 0000:04:00.0: eth3: link down
[ 7535.814221] [drm] PCIE GART of 512M enabled (table at 0x00000000C0040000).
[ 7535.814691] radeon 0000:01:05.0: WB enabled
[ 7535.845617] [drm] ring test succeeded in 1 usecs
[ 7535.845630] [drm] ib test succeeded in 0 usecs
[ 7535.948503] ata8.01: ACPI cmd ef/03:0c:00:00:00:b0 (SET FEATURES) filtered out
[ 7535.948507] ata8.01: ACPI cmd ef/03:42:00:00:00:b0 (SET FEATURES) filtered out
[ 7535.948511] ata8.01: ACPI cmd f5/00:00:00:00:00:b0 (SECURITY FREEZE LOCK) filtered out
[ 7535.956505] ata8.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
[ 7535.956509] ata8.00: ACPI cmd ef/03:42:00:00:00:a0 (SET FEATURES) filtered out
[ 7535.956513] ata8.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 7535.964440] ata8.00: configured for UDMA/33
[ 7535.980439] ata8.01: configured for UDMA/33
[ 7535.996035] usb 2-4: reset high-speed USB device number 3 using ehci_hcd
[ 7536.104050] ata5: SATA link down (SStatus 0 SControl 300)
[ 7536.104083] ata4: SATA link down (SStatus 0 SControl 300)
[ 7536.104114] ata3: SATA link down (SStatus 0 SControl 300)
[ 7536.104150] ata6: SATA link down (SStatus 0 SControl 300)
[ 7536.360029] ata1: softreset failed (device not ready)
[ 7536.360032] ata1: applying PMP SRST workaround and retrying
[ 7536.532044] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 7536.532744] ata1.00: configured for UDMA/100
[ 7537.836664] r8169 0000:04:00.0: eth3: link up
[ 7545.796022] ata2: softreset failed (device not ready)
[ 7548.864018] ata2: softreset failed (device not ready)
[ 7548.864021] ata2: applying PMP SRST workaround and retrying
[ 7549.036029] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 7549.048129] ata2.00: configured for UDMA/100
[ 7549.093163] PM: resume of devices complete after 13308.621 msecs
[ 7549.093677] PM: Finishing wakeup.
[ 7549.093678] Restarting tasks ... done.
[ 8383.363803] PM: Syncing filesystems ... done.
[ 8383.866421] PM: Preparing system for mem sleep
[ 8383.924385] Freezing user space processes ... (elapsed 0.01 seconds) done.
[ 8383.940071] Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
[ 8383.956037] PM: Entering mem sleep
[ 8383.956072] Suspending console(s) (use no_console_suspend to debug)
[ 8383.956504] sd 1:0:0:0: [sdb] Synchronizing SCSI cache
[ 8383.956589] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 8383.956874] sd 1:0:0:0: [sdb] Stopping disk
[ 8383.957394] r8169 0000:04:00.0: eth3: link down
[ 8383.958901] sd 0:0:0:0: [sda] Stopping disk
[ 8383.960090] snd_hda_intel 0000:00:14.2: PCI INT A disabled
[ 8383.960404] pata_atiixp 0000:00:14.1: PCI INT A disabled
[ 8383.972147] ohci_hcd 0000:00:12.0: PCI INT A disabled
[ 8383.972157] ohci_hcd 0000:00:12.1: PCI INT A disabled
[ 8383.988039] ehci_hcd 0000:00:13.2: PCI INT B disabled
[ 8384.024031] ehci_hcd 0000:00:12.2: PCI INT B disabled
[ 8384.036048] ohci_hcd 0000:00:14.5: PCI INT C disabled
[ 8384.036075] ohci_hcd 0000:00:13.0: PCI INT A disabled
[ 8384.036100] ohci_hcd 0000:00:13.1: PCI INT A disabled
[ 8384.097648] radeon 0000:01:05.0: PCI INT A disabled
[ 8384.612845] ahci 0000:00:11.0: PCI INT A disabled
[ 8384.628062] PM: suspend of devices complete after 671.772 msecs
[ 8384.628283] r8169 0000:04:00.0: PME# enabled
[ 8384.628295] pcieport 0000:00:0a.0: wake-up capability enabled by ACPI
[ 8384.644148] ohci_hcd 0000:00:14.5: wake-up capability enabled by ACPI
[ 8384.644248] ehci_hcd 0000:00:13.2: PME# enabled
[ 8384.644252] ehci_hcd 0000:00:13.2: wake-up capability enabled by ACPI
[ 8384.660053] ohci_hcd 0000:00:13.1: wake-up capability enabled by ACPI
[ 8384.660080] ohci_hcd 0000:00:13.0: wake-up capability enabled by ACPI
[ 8384.660112] ehci_hcd 0000:00:12.2: PME# enabled
[ 8384.660116] ehci_hcd 0000:00:12.2: wake-up capability enabled by ACPI
[ 8384.676053] ohci_hcd 0000:00:12.1: wake-up capability enabled by ACPI
[ 8384.676079] ohci_hcd 0000:00:12.0: wake-up capability enabled by ACPI
[ 8384.676176] PM: late suspend of devices complete after 48.108 msecs
[ 8384.676302] ACPI: Preparing to enter system sleep state S3
[ 8385.076280] PM: Saving platform NVS memory
[ 8385.076702] Disabling non-boot CPUs ...
[ 8385.180016] CPU 1 is now offline
[ 8385.180583] ACPI: Low-level resume complete
[ 8385.180583] PM: Restoring platform NVS memory
[ 8385.180583] Enabling non-boot CPUs ...
[ 8385.180583] Booting Node 0 Processor 1 APIC 0x1
[ 8385.180583] smpboot cpu 1: start_ip = 9b000
[ 8385.078061] Initializing CPU#1
[ 8385.078061] Calibrating delay loop (skipped) already calibrated this CPU
[ 8385.192346] NMI watchdog enabled, takes one hw-pmu counter.
[ 8385.192578] CPU1 is up
[ 8385.193185] ACPI: Waking up from system sleep state S3
[ 8385.193673] pcieport 0000:00:09.0: restoring config space at offset 0x1 (was 0x100107, writing 0x100507)
[ 8385.193704] pcieport 0000:00:0a.0: restoring config space at offset 0x1 (was 0x100107, writing 0x100507)
[ 8385.193729] ahci 0000:00:11.0: restoring config space at offset 0xf (was 0x100, writing 0x104)
[ 8385.193786] ohci_hcd 0000:00:12.0: wake-up capability disabled by ACPI
[ 8385.193814] ohci_hcd 0000:00:12.1: wake-up capability disabled by ACPI
[ 8385.208052] ehci_hcd 0000:00:12.2: BAR 0: set to [mem 0xfddff000-0xfddff0ff] (PCI address [0xfddff000-0xfddff0ff])
[ 8385.208081] ehci_hcd 0000:00:12.2: restoring config space at offset 0x1 (was 0x2b00000, writing 0x2b00112)
[ 8385.208097] ehci_hcd 0000:00:12.2: wake-up capability disabled by ACPI
[ 8385.208102] ehci_hcd 0000:00:12.2: PME# disabled
[ 8385.208129] ohci_hcd 0000:00:13.0: wake-up capability disabled by ACPI
[ 8385.208156] ohci_hcd 0000:00:13.1: wake-up capability disabled by ACPI
[ 8385.224032] ehci_hcd 0000:00:13.2: BAR 0: set to [mem 0xfddf6800-0xfddf68ff] (PCI address [0xfddf6800-0xfddf68ff])
[ 8385.224061] ehci_hcd 0000:00:13.2: restoring config space at offset 0x1 (was 0x2b00000, writing 0x2b00113)
[ 8385.224076] ehci_hcd 0000:00:13.2: wake-up capability disabled by ACPI
[ 8385.224080] ehci_hcd 0000:00:13.2: PME# disabled
[ 8385.224134] pata_atiixp 0000:00:14.1: restoring config space at offset 0x3 (was 0x0, writing 0x4000)
[ 8385.224172] snd_hda_intel 0000:00:14.2: restoring config space at offset 0x1 (was 0x4100006, writing 0x4100002)
[ 8385.224252] ohci_hcd 0000:00:14.5: wake-up capability disabled by ACPI
[ 8385.224278] radeon 0000:01:05.0: restoring config space at offset 0xf (was 0x1ff, writing 0x10b)
[ 8385.224289] radeon 0000:01:05.0: restoring config space at offset 0x3 (was 0x800000, writing 0x800010)
[ 8385.224316] r8169 0000:04:00.0: restoring config space at offset 0xc (was 0x0, writing 0xfebf0000)
[ 8385.224324] r8169 0000:04:00.0: restoring config space at offset 0x8 (was 0xc, writing 0xfcfe000c)
[ 8385.224330] r8169 0000:04:00.0: restoring config space at offset 0x6 (was 0xc, writing 0xfcfff00c)
[ 8385.224339] r8169 0000:04:00.0: restoring config space at offset 0x1 (was 0x100107, writing 0x100507)
[ 8385.224505] PM: early resume of devices complete after 30.911 msecs
[ 8385.224600] ahci 0000:00:11.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 8385.224643] ohci_hcd 0000:00:12.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 8385.224697] ohci_hcd 0000:00:12.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 8385.224747] ehci_hcd 0000:00:12.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 8385.224844] ohci_hcd 0000:00:13.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 8385.224866] ohci_hcd 0000:00:13.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 8385.224890] ehci_hcd 0000:00:13.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 8385.224902] pata_atiixp 0000:00:14.1: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 8385.224914] snd_hda_intel 0000:00:14.2: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 8385.224930] ohci_hcd 0000:00:14.5: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 8385.224954] pcieport 0000:00:0a.0: wake-up capability disabled by ACPI
[ 8385.224960] radeon 0000:01:05.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 8385.224962] r8169 0000:04:00.0: PME# disabled
[ 8385.224966] radeon 0000:01:05.0: setting latency timer to 64
[ 8385.232940] sd 0:0:0:0: [sda] Starting disk
[ 8385.232996] sd 1:0:0:0: [sdb] Starting disk
[ 8385.244157] r8169 0000:04:00.0: eth3: link down
[ 8385.254313] [drm] PCIE GART of 512M enabled (table at 0x00000000C0040000).
[ 8385.254807] radeon 0000:01:05.0: WB enabled
[ 8385.285739] [drm] ring test succeeded in 1 usecs
[ 8385.285752] [drm] ib test succeeded in 0 usecs
[ 8385.392501] ata8.01: ACPI cmd ef/03:0c:00:00:00:b0 (SET FEATURES) filtered out
[ 8385.392505] ata8.01: ACPI cmd ef/03:42:00:00:00:b0 (SET FEATURES) filtered out
[ 8385.392509] ata8.01: ACPI cmd f5/00:00:00:00:00:b0 (SECURITY FREEZE LOCK) filtered out
[ 8385.400504] ata8.00: ACPI cmd ef/03:0c:00:00:00:a0 (SET FEATURES) filtered out
[ 8385.400508] ata8.00: ACPI cmd ef/03:42:00:00:00:a0 (SET FEATURES) filtered out
[ 8385.400511] ata8.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
[ 8385.408441] ata8.00: configured for UDMA/33
[ 8385.424456] ata8.01: configured for UDMA/33
[ 8385.436064] usb 2-4: reset high-speed USB device number 3 using ehci_hcd
[ 8385.544057] ata4: SATA link down (SStatus 0 SControl 300)
[ 8385.544089] ata6: SATA link down (SStatus 0 SControl 300)
[ 8385.544119] ata5: SATA link down (SStatus 0 SControl 300)
[ 8385.544156] ata3: SATA link down (SStatus 0 SControl 300)
[ 8385.800034] ata1: softreset failed (device not ready)
[ 8385.800038] ata1: applying PMP SRST workaround and retrying
[ 8385.972037] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 8385.972736] ata1.00: configured for UDMA/100
[ 8387.335281] r8169 0000:04:00.0: eth3: link up
[ 8395.236021] ata2: softreset failed (device not ready)
[ 8398.584018] ata2: softreset failed (device not ready)
[ 8398.584022] ata2: applying PMP SRST workaround and retrying
[ 8398.756029] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 8398.768233] ata2.00: configured for UDMA/100
[ 8398.811217] PM: resume of devices complete after 13586.678 msecs
[ 8398.811697] PM: Finishing wakeup.
[ 8398.811699] Restarting tasks ... done.

Attachment: signature.asc
Description: This is a digitally signed message part

_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/dri-devel

[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux