Hi,
On Fri, Jan 10, 2020 at 04:11:40PM +0200, Stefan Mavrodiev wrote:
> Add HDMI audio support for the sun4i-hdmi encoder, used on
> the older Allwinner chips - A10, A20, A31.
>
> Most of the code is based on the BSP implementation. In it
> dditional formats are supported (S20_3LE and S24_LE), however
> there where some problems with them and only S16_LE is left.
>
> Signed-off-by: Stefan Mavrodiev <stefan@xxxxxxxxxx>
> ---
> drivers/gpu/drm/sun4i/Kconfig | 1 +
> drivers/gpu/drm/sun4i/Makefile | 1 +
> drivers/gpu/drm/sun4i/sun4i_hdmi.h | 30 ++
> drivers/gpu/drm/sun4i/sun4i_hdmi_audio.c | 375 +++++++++++++++++++++++
> drivers/gpu/drm/sun4i/sun4i_hdmi_enc.c | 4 +
> 5 files changed, 411 insertions(+)
> create mode 100644 drivers/gpu/drm/sun4i/sun4i_hdmi_audio.c
>
> diff --git a/drivers/gpu/drm/sun4i/Kconfig b/drivers/gpu/drm/sun4i/Kconfig
> index 37e90e42943f..192b732b10cd 100644
> --- a/drivers/gpu/drm/sun4i/Kconfig
> +++ b/drivers/gpu/drm/sun4i/Kconfig
> @@ -19,6 +19,7 @@ if DRM_SUN4I
> config DRM_SUN4I_HDMI
> tristate "Allwinner A10 HDMI Controller Support"
> default DRM_SUN4I
> + select SND_PCM_ELD
> help
> Choose this option if you have an Allwinner SoC with an HDMI
> controller.
> diff --git a/drivers/gpu/drm/sun4i/Makefile b/drivers/gpu/drm/sun4i/Makefile
> index 0d04f2447b01..e2d82b451c36 100644
> --- a/drivers/gpu/drm/sun4i/Makefile
> +++ b/drivers/gpu/drm/sun4i/Makefile
> @@ -5,6 +5,7 @@ sun4i-frontend-y += sun4i_frontend.o
> sun4i-drm-y += sun4i_drv.o
> sun4i-drm-y += sun4i_framebuffer.o
>
> +sun4i-drm-hdmi-y += sun4i_hdmi_audio.o
> sun4i-drm-hdmi-y += sun4i_hdmi_ddc_clk.o
> sun4i-drm-hdmi-y += sun4i_hdmi_enc.o
> sun4i-drm-hdmi-y += sun4i_hdmi_i2c.o
> diff --git a/drivers/gpu/drm/sun4i/sun4i_hdmi.h b/drivers/gpu/drm/sun4i/sun4i_hdmi.h
> index 7ad3f06c127e..456964e681b0 100644
> --- a/drivers/gpu/drm/sun4i/sun4i_hdmi.h
> +++ b/drivers/gpu/drm/sun4i/sun4i_hdmi.h
> @@ -42,7 +42,32 @@
> #define SUN4I_HDMI_VID_TIMING_POL_VSYNC BIT(1)
> #define SUN4I_HDMI_VID_TIMING_POL_HSYNC BIT(0)
>
> +#define SUN4I_HDMI_AUDIO_CTRL_REG 0x040
> +#define SUN4I_HDMI_AUDIO_CTRL_ENABLE BIT(31)
> +#define SUN4I_HDMI_AUDIO_CTRL_RESET BIT(30)
> +
> +#define SUN4I_HDMI_AUDIO_FMT_REG 0x048
> +#define SUN4I_HDMI_AUDIO_FMT_SRC BIT(31)
> +#define SUN4I_HDMI_AUDIO_FMT_LAYOUT BIT(3)
> +#define SUN4I_HDMI_AUDIO_FMT_CH_CFG(n) (n - 1)
There's the issue multiple times in the headers, but you should wrap n
in parentheses to make sure we have no issue with precedence when
calling the macro.
> +int sun4i_hdmi_audio_create(struct sun4i_hdmi *hdmi)
> +{
> + struct snd_soc_card *card = &sun4i_hdmi_audio_card;
> + struct snd_soc_dai_link_component *comp;
> + struct snd_soc_dai_link *link;
> + int ret;
> +
> + ret = devm_snd_dmaengine_pcm_register(hdmi->dev,
> + &sun4i_hdmi_audio_pcm_config, 0);
> + if (ret) {
> + DRM_ERROR("Could not register PCM\n");
> + return ret;
> + }
> +
> + ret = devm_snd_soc_register_component(hdmi->dev,
> + &sun4i_hdmi_audio_component,
> + &sun4i_hdmi_audio_dai, 1);
> + if (ret) {
> + DRM_ERROR("Could not register DAI\n");
> + return ret;
> + }
> +
> + link = devm_kzalloc(hdmi->dev, sizeof(*link), GFP_KERNEL);
> + if (!link)
> + return -ENOMEM;
> +
> + comp = devm_kzalloc(hdmi->dev, sizeof(*comp) * 3, GFP_KERNEL);
> + if (!comp)
> + return -ENOMEM;
> +
> + link->cpus = &comp[0];
> + link->codecs = &comp[1];
> + link->platforms = &comp[2];
> +
> + link->num_cpus = 1;
> + link->num_codecs = 1;
> + link->num_platforms = 1;
> +
> + link->playback_only = 1;
> +
> + link->name = "SUN4I-HDMI";
> + link->stream_name = "SUN4I-HDMI PCM";
> +
> + link->codecs->name = dev_name(hdmi->dev);
> + link->codecs->dai_name = sun4i_hdmi_audio_dai.name;
> +
> + link->cpus->dai_name = dev_name(hdmi->dev);
> +
> + link->platforms->name = dev_name(hdmi->dev);
> +
> + link->dai_fmt = SND_SOC_DAIFMT_I2S;
> +
> + card->dai_link = link;
> + card->num_links = 1;
> + card->dev = hdmi->dev;
> +
> + snd_soc_card_set_drvdata(card, hdmi);
> + return devm_snd_soc_register_card(hdmi->dev, card);
Out of curiosity, did you try to remove the module with that patch
applied? IIRC, these functions will overwrite the device drvdata, and
we will try to access them in unbind / remove.
> +}
> diff --git a/drivers/gpu/drm/sun4i/sun4i_hdmi_enc.c b/drivers/gpu/drm/sun4i/sun4i_hdmi_enc.c
> index a7c4654445c7..79ecd89fb705 100644
> --- a/drivers/gpu/drm/sun4i/sun4i_hdmi_enc.c
> +++ b/drivers/gpu/drm/sun4i/sun4i_hdmi_enc.c
> @@ -114,6 +114,9 @@ static void sun4i_hdmi_enable(struct drm_encoder *encoder)
> val |= SUN4I_HDMI_VID_CTRL_HDMI_MODE;
>
> writel(val, hdmi->base + SUN4I_HDMI_VID_CTRL_REG);
> +
> + if (hdmi->hdmi_audio && sun4i_hdmi_audio_create(hdmi))
> + DRM_ERROR("Couldn't create the HDMI audio adapter\n");
So you create the audio card each time the display is enabled? I guess
this is to deal with the hotplug?
I'm not sure this is the right thing to do. If I remember well, the
ELD are here precisely to let userspace know that the display is
plugged (and audio-capable) or not.
Also, you don't remove that card in the disable, which mean that if
you end up in a situation where you would enable the display, disable
it and then enable it again, you have two audio cards now.
Thanks!
Maxime
Attachment:
signature.asc
Description: PGP signature
_______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.freedesktop.org/mailman/listinfo/dri-devel
