On 2020-01-09 10:20 a.m., Mario Kleiner wrote:
> If the current eDP link settings, as read from hw, provide a higher
> bandwidth than the verified_link_cap ones (= reported_link_cap), then
> override verified_link_cap with current settings.
>
> These initial current eDP link settings have been set up by
> firmware during boot, so they should work on the eDP panel.
> Therefore use them if the firmware thinks they are good and
> they provide higher link bandwidth, e.g., to enable higher
> resolutions / color depths.
>
This only works when taking over from UEFI, so on boot or resume from
hibernate. This wouldn't work on a normal suspend/resume.
Can you check if setting link->dc->config.optimize_edp_link_rate (see
first if statement in detect_edp_sink_caps) fixes this? I imagine we
need to read the reported settings from DP_SUPPORTED_LINK_RATES and fail
to do so.
Thanks,
Harry
> This fixes a problem found on the MacBookPro 2017 Retina panel:
>
> The panel reports 10 bpc color depth in its EDID, and the
> firmware chooses link settings at boot which support enough
> bandwidth for 10 bpc (324000 kbit/sec aka LINK_RATE_RBR2),
> but the DP_MAX_LINK_RATE dpcd register only reports 2.7 Gbps
> as possible, so verified_link_cap is only good for 2.7 Gbps
> and 8 bpc, not providing the full color depth of the panel.
>
> Signed-off-by: Mario Kleiner <mario.kleiner.de@xxxxxxxxx>
> Cc: Alex Deucher <alexander.deucher@xxxxxxx>
> ---
> drivers/gpu/drm/amd/display/dc/core/dc_link.c | 21 +++++++++++++++++++
> 1 file changed, 21 insertions(+)
>
> diff --git a/drivers/gpu/drm/amd/display/dc/core/dc_link.c b/drivers/gpu/drm/amd/display/dc/core/dc_link.c
> index 5ea4a1675259..f3acdb8fead5 100644
> --- a/drivers/gpu/drm/amd/display/dc/core/dc_link.c
> +++ b/drivers/gpu/drm/amd/display/dc/core/dc_link.c
> @@ -819,6 +819,27 @@ static bool dc_link_detect_helper(struct dc_link *link,
> case SIGNAL_TYPE_EDP: {
> detect_edp_sink_caps(link);
> read_current_link_settings_on_detect(link);
> +
> + /* If cur_link_settings provides higher bandwidth than
> + * verified_link_cap, then use cur_link_settings as new
> + * verified_link_cap, as it obviously works according to
> + * firmware boot setup.
> + *
> + * This has been observed on the Apple MacBookPro 2017
> + * Retina panel, which boots with a link setting higher
> + * than what dpcd[DP_MAX_LINK_RATE] claims as possible.
> + * Overriding allows to run the panel at 10 bpc / 30 bit.
> + */
> + if (dc_link_bandwidth_kbps(link, &link->cur_link_settings) >
> + dc_link_bandwidth_kbps(link, &link->verified_link_cap)) {
> + DC_LOG_DETECTION_DP_CAPS(
> + "eDP current link setting bw %d kbps > verified_link_cap %d kbps. Override.",
> + dc_link_bandwidth_kbps(link, &link->cur_link_settings),
> + dc_link_bandwidth_kbps(link, &link->verified_link_cap));
> +
> + link->verified_link_cap = link->cur_link_settings;
> + }
> +
> sink_caps.transaction_type = DDC_TRANSACTION_TYPE_I2C_OVER_AUX;
> sink_caps.signal = SIGNAL_TYPE_EDP;
> break;
>
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/dri-devel
